-
VTT BMW Billet One-Way Crankcase Breather
VTT is proud to introduce the first and only plug-and-play crankcase breather kit designed for BMW applications utilizing the two-prong oil cap style.
Installation is simple—remove your factory oil cap, install the breather, and immediately:
- Reduce crankcase pressure
- Improve turbo oil drainage
- Free up horsepower
- Add a clean, performance-focused look to your engine bay
Versatile Performance
This breather can be:
- Used with the stock PCV system to relieve crankcase pressure
- Paired with aftermarket PCV setups for maximum pressure relief
Premium Construction
Machined from 6061-T6 billet aluminum and anodized black for durability and corrosion resistance, the VTT breather is built to perform.
Features include:
- (4) Stainless steel internal baffles for superior oil control
- PTFE one-way check ball
- High-quality breather filter
- Secure clamp system
Together, these components ensure crankcase pressure is properly vented while maintaining effective oil separation.
Fitment
This breather fits most (not all) BMW engines utilizing the two-prong oil cap, including but not limited to:
- N54, N55, S55
- S54, S85
- S63, S63TU, N63
- Most BMW diesel models
⚠️ Important Notes:
- Fitment may vary depending on valve cover design and surrounding components
- We do not recommend use on S63, S63TU, or S68 platforms (F90, G90 M5, etc.)
- Installation on non-recommended applications is at your own risk and renders the item non-returnable if used
-
VTT CNC Billet check valve that can be used for a variety of uses including a vacuum/boost check valve when removing the stock PCV system, and still wanting to run vacuum to the crankcase. Rated at over 100 psi, with a cracking psi of .25psi.
-
NGK 95706 Spark plug set required for running 100% e85, and high boost on many BMW applications, including N54, N55, S55, etc. Plugs can be bought as a set of 6. You can add pre-gapping for an additional charge
-
VTT "Spline Lock" Crank Hub System – N54 / N55 / S55
VTT is proud to offer the only complete crank hub solution for BMW N54, N55, and S55 engines that does not require drilling the crankshaft for pins.
Our innovative hub features proprietary Spline Lock Technology—a high-tolerance, precision-machined spline system that presses into the crank and positively locks the hub in place, eliminating the need for traditional pinning or welding.
After months of rigorous development and over 10 different prototype revisions, our final production version was put to the test. In our in-house trials, the hub outperformed expectations—breaking our testing rig before it ever slipped. Real-world validation has been conducted on the VTT N54 race car, which spins to 8,000 RPM and produces over 900 WHP.
Key Benefits:
-
No crank drilling required – stock-like installation
-
Minimal labor – fully reversible with no permanent modification
-
Tested to extreme conditions – race-proven at high RPM and power
-
Exclusively compatible with VTT’s Crank Bolt Capture (CBC) for maximum security
⚠️ Spline Lock hubs are recommended be used with the VTT Crank Bolt Capture system. They are not intended to run independently.
-
-
VTT Billet CNC Oil Caps
Upgrade your BMW engine bay with a touch of precision and durability. VTT Billet CNC Oil Caps replace the factory plastic cap with a high-quality, performance-focused alternative.
-
Premium Materials – Machined from 6061-T6 aircraft-grade aluminum with stainless steel locking tabs for a secure fit and long-lasting reliability.
-
Anodized Finishes – Available in red, black, blue, purple, gold, or clear anodizing to match your build’s style.
-
Perfect Fitment – Designed for all BMW engines with a two-prong locking tab oil cap design, including (but not limited to):
THIS CAP DOES NOT FIT, B58TU, S58, A90/91 SUPRA, THIS ONLY FITS 2 PRONG CAP STYLE
-
-
VTT BILLET BMW N54/55 Crank Seal Guard.
It is a well-known issue on the BMW N54/N55/S55 platforms that your serpentine belt can fail for various reasons, when this happens you have a high chance of the belt getting sucked behind the front damper, and then being pushed past the crank seal into your oil pan. From there it can get sucked into the oil pick up causing total engine failure, even if you do not lose the engine it is a COSTLY repair to remove the sub-frame and drop the oil pan to remove the belt. The best way to combat this is to watch for oil leaks and keep up on your maintenance. BUT Even with those preventative measures, pre-mature belt failure can occur. This crank seal guard installs over your front crank seal and will keep the belt from being sucked in if a belt failure does occur. This is a cheap way to ensure you do not end up having to replace your motor from oil starvation due to an ingested belt. -
VTT S55/N55 EWG Billet Aluminum Valve Cover
Performance. Durability. Style.
VTT is proud to introduce the S55/N55 EWG Billet Aluminum Valve Cover — engineered for enthusiasts who demand performance and reliability without compromising design. Whether you’re replacing an aging OEM plastic cover or running a single turbo conversion that requires better clearance and heat resistance, this cover delivers on every front.
Designed to eliminate the failure-prone factory PCV system, the VTT Billet Valve Cover gives you complete control over your crankcase ventilation setup. Each unit is fully baffled to reduce oil carryover and maintain clean, efficient crankcase operation. For best results, pair it with a quality catch can system.
Valve Cover Features
-
100% CNC-Machined from 6061-T6 Billet Aluminum – Exceptional strength, precision, and durability
-
Anodized Finish in Multiple Colors – Choose a clean, custom look for your engine bay
-
Lightweight Design – 9.7 lbs (compared to 7.9 lbs stock; only a 1.8 lb difference)
-
Fully Modular PCV Configuration – Configure your PCV system exactly how you want it
-
Fully Baffled Ports – Prevents oil escape and ensures consistent crankcase pressure
-
Ideal for Single Turbo Conversions – Provides improved clearance and superior heat resistance
-
Durable & Reliable Construction – A significant upgrade from the OEM plastic cover
-
-
Our studs are forged from cold-rolled 10.9-class steel and finished with a black oxide corrosion-resistant coating, ensuring years of dependable service in both street and motorsport environments.
We offer one optimized size: 85mm overall length, with the following breakdown:
-
75mm total thread length
-
10mm bull nose for smooth lug engagement
-
12mm short-thread section (hub side)
-
12mm unthreaded shank
-
48mm long-thread section (lug nut side)
These studs are coated using Black Oxide, which does protect, BUT even when using Black Oxide, the studs CAN develop surface rust if left to the elements. We suggest a slight coat of WD-40 when you clean your wheels to prevent this.
These studs are coated using Black Oxide, which does protect, BUT even when using Black Oxide, the studs CAN develop surface rust if left to the elements. We suggest a slight coat of WD-40 when you clean your wheels to prevent this.
-
-
Looking to convert your 5x112 M14x1.25 vehicle, such as A90/91 Toyota Supra, and 2020+ BMW G-series, to 5x114 to open up your wheel options? We got covered with our VTT wheel stud conversion kits. These kits are forged cold-rolled steel in 10.9 class, with Black Oxide corrosion-resistant coating for years of use, and convert your vehicle to M12x1.50 wheel studs, which allow you to fit 5x114 wheels with no other changes. No wobble bolts or redrilling here. Simply install the studs, put the wheel on, and the lug nuts will center the wheel. This kit is Black Studs with Black Lugnuts, and we offer it in 10 or 20 pieces if you want to only do the front/rear or both.
Our studs are forged from cold-rolled 10.9-class steel and finished with a black oxide corrosion-resistant coating, ensuring years of dependable service in both street and motorsport environments.
We offer one optimized size: 85mm overall length, with the following breakdown:
-
75mm total thread length
-
10mm bull nose for smooth lug engagement
-
12mm short-thread section (hub side)
-
12mm unthreaded shank
-
48mm long-thread section (lug nut side)
PLEASE NOTE – THESE STUDS WILL ONLY WORK IF YOUR WHEELS ARE DRILLED M14 THESE WILL NOT WORK FOR WHEELS DRILLED M12!
These studs are coated using Black Oxide, which does protect, BUT even when using Black Oxide, the studs CAN develop surface rust if left to the elements. We suggest a slight coat of WD-40 when you clean your wheels to prevent this.
DO NOT USE ANY HUB-CENTERING SLEEVES WITH THESE CONVERSION STUDS, THE LUGS WILL CENTER THE WHEELS. THE USE OF A CENTERING SLEEVE MAY LEAD TO STUDS BREAKING. FOR INSTALLATION YOU MUST SNUG EACH LUG UP SLOWLY, AND IN A STAR PATTERN TO GET THE WHEEL CENTERED ON THE LUGS, FAILURE TO DO SO CAN ALSO LEAD TO FAILURE.
-
-
VTT Billet Wheel Spacers
VTT is proud to offer billet wheel spacers for most VAG, BMW, and the A90/91 Toyota Supra platforms.
Each spacer is:
-
CNC-machined from 6061-T6 aluminum
-
Hard anodized black for a long, corrosion-free life
We offer multiple fitments and sizes to suit a wide range of applications.
THESE ARE SOLD INDIVIDUALLY, FOR ONE AXLE ORDER TWO FOR A COMPLETE SET ORDER FOUR.
ANYTHING OVER 5MM WILL REQUIRE LONGER BOLTS OR STUDS. YOU CAN CHOOSE TO ADD A VTT WHEEL STUD KIT FROM THE OPTIONS.
PLEASE DOUBLE CHECK YOUR BOLT PATTERN AND HUB BORE BEFORE YOU ORDER. INSTALLED SPACERS CANNOT BE RETURNED!
-
-
VTT is proud to offer Titanium wheel stud kits for the owner looking for the lowest possible unsprung weight while maintaining high strength, and good looks as all come with an amazing burnt finish. This kit is 60% lighter than factory steel studs and nuts with a total kit of 20 nuts, and studs being 3.1LBS. Sets of 10 are 1.55 lbs
-
VTT High-Performance Ignition Coils
BMW N5X • B58 / S58 / B48 • VAG Platforms
Vargas Turbo Technologies (VTT) is proud to offer high-performance ignition coil upgrades for BMW N5X platforms, B58/S58/B48 engines, and select VAG applications.
Development & Testing
Our ignition coil program began with extensive outreach to multiple OEM and aftermarket coil manufacturers. We commissioned individual prototype coils, then subjected them to rigorous, repeatable testing in the United States to ensure they matched or exceeded factory performance standards.
Only the highest-performing designs were selected and produced to VTT’s exact specifications and colorways. These are not rebranded or cosmetic coils—each set is performance-validated.
-
Do you work on BMW engines across multiple platforms? Tired of modifying universal engine stand plates just to make them fit? Frustrated by losing access to the flywheel side once the engine is mounted?
We were too—so we built the solution.
The VTT BMW Engine Stand Plate is a true bolt-on design that keeps the flywheel end fully accessible while providing a strong, stable mounting solution for your engine builds.
Machined from solid 6061-T6 billet aluminum and anodized in five colors for long-term durability and corrosion resistance, these plates are lightweight yet rated for over 1200 lbs.
Fitment: N54, N55, S55, B58, S58 (more coming soon)
Note: The stand tube is 60mm or 2.36” OD, which fits most engine stands, but not all—please measure before purchasing.
Key Features:
- Lightweight, high-strength billet 6061-T6 construction
- Durable anodized finish
- Direct bolt-on to intake-side motor mount location
- Full clearance for accessories and flywheel/flex plate access
- Built-in provisions for locator pin and rotation bar
-
Tired of your Dragy flying all over the car as you try to do runs? Tired of low sats or no sats warning due to improper location of the Dragy in the vehicle? Well say goodbye to those issues with our new Carbon Fiber and Plastic Dragy holders. These are made from either 100% Pre-Preg Carbon Fiber, or molded plastic for a perfect fit. The carbon fiber gives it just the right look to add to your performance vehicle! Each holder has dual Suction cups and will stick to any smooth surface. We suggest mounting them in the upper left or right corner of your windshield with a full view of the sky. Dragy holder features
- Stop your Dragy from flying off the dash, and having to search for it
- Position your Dragy in the optimal position for the best satellite coverage
- VTT Dragy holder exposes the entire top of the Dragy so nothing is blocking the receiver from the Satellite
- The charging port is not blocked and can be accessed with the cover on
- Choose from REAL Carbon Fiber or Molded Plastic
-
VTT is proud to offer our Billet Aluminum DCT Transmission Pan – the ultimate upgrade over the factory plastic pan.
CNC-machined from 6061-T6 aluminum and anodized in a variety of colors, this pan not only adds strength and durability but also nearly doubles fluid capacity for improved cooling and performance. With added serviceability features and premium components, this is the last DCT pan you’ll ever need.
Key Features
-
6061-T6 Billet Construction – Stronger and longer-lasting than the stock plastic pan.
-
Increased Fluid Capacity – 2000ML vs. the OEM 1150ML — an 80% increase.
-
Cooling Efficiency – Machined external fins to aid heat dissipation.
-
Built-In Protection – Integrated rare-earth magnet pulls metal debris from the fluid.
-
Premium Sealing – Reusable US-made Viton gasket for a leak-free seal.
-
Easy Servicing – Includes a -6 ORB drain plug for quick and clean fluid changes.
-
Anodized Finish – Available in multiple colors for long-lasting corrosion resistance and style.
-
-
Introducing the VTT OBD-LOCK – Enhanced Security & Improved Design!
We are excited to announce our OBD-LOCK! This latest version has been completely redesigned for improved strength, ease of installation, and enhanced protection. Key upgrades include:
No more OBD port penetration – eliminates any risk of damage
Revised thread style – prevents stripping for a secure fit
Stronger, more durable design – ensures maximum securityUltimate OBD Port Protection
The VTT OBD-LOCK is precision-machined from billet 6061-T6 aluminum and is engineered to completely lock out your OBD port, preventing unauthorized access.
Anti-Theft Protection – Prevents thieves from accessing the OBD port to duplicate keys or disable security systems
Dealer/Tech Lockout – Stops unauthorized tune changes or system modifications
Tamper-Proof Design – Cannot be removed without physically destroying the OBD port unless the correct tool is usedVTT OBD-LOCK – Version 2 NON-GM
Universal Fit for All Non-GM (General Motors) VehiclesThis device is compatible with all non-GM vehicles, including but not limited to:
-
All VAG group vehicles (VW, Audi, Bentley, etc.) — including recessed port VW/Audi models
-
Ford, Nissan, Honda, Toyota, Porsche, Dodge, Ram, Jeep, Kia, Subaru, and more
Not compatible with GM (General Motors) vehicles.
VTT OBD-LOCK – Version 2 GM
Universal Fit for GM (General Motors) Vehicles ONLYThis version is specifically designed for General Motors vehicles, including GM, Chevrolet, Cadillac, Holden, and other GM-branded models.
If your vehicle is anything other than a General Motors product, you will need the Non-GM version.
-
-
VTT Billet Velocity Stack (V-Stack)
3" • 4" • 5" Inlet Sizes
Running an open turbo and want to straighten airflow into the compressor for maximum efficiency? The VTT Billet Velocity Stack is exactly what you need.
Backed by fluid-dynamics principles, a proper bellmouth / velocity stack smooths incoming airflow, reduces turbulence, and improves air entry into the turbocharger—or intake on naturally aspirated applications. Unlike thin, stamped alternatives, our V-Stacks are precision-machined for strength, consistency, and performance.
Each unit is CNC-machined from 6061-T6 billet aluminum and anodized for durability and corrosion resistance. Available in 3", 4", and 5" inlet sizes, these stacks are designed to fit any intake tubing or turbocharger inlet of the corresponding diameter.
-
Looking to protect your single turbo investment, dont have a ton of room, and need a low profile filter that can flow what you need? VTT Has you covered with our Low Profile Single turbo Air Filters. These filters are custom-made for VTT. They are made with a heat-resistant silicone base, and a high-flowing cotton weave element with a pre-oiled design to catch contaminates but allow free flow. We currently offer them in Black, and 3 flange sizes. 3", 4" and 5" flange. With two filter heights. Tested at over 1200WHP with no loss of power observed. Filter Options - Offered in White, and Black with the following dimensions Short - 3.75" Tall, 7.5" OD Large end, 5" Small end 3", 4", or 5" Flange Tall - 4.5" Tall, 7.5" OD Large end, 5" Small end 3", 4", or 5" Flange
-
VTT S55 Silicone Charge Pipes – BMW M3 / M4
Looking to get the most efficient turbocharger operation out of your S55-powered BMW? The best way to do that is by eliminating all restriction in the inlet and charge tract—starting with the factory charge pipes.
The OEM pipes are poorly designed and severely flattened as they exit the turbos before the intercooler, creating unnecessary restriction. VTT S55 Silicone Charge Pipes eliminate this bottleneck by providing a true, full 2" ID from the turbochargers to the intercooler, allowing maximum airflow and improved turbo efficiency.
Unlike aluminum pipes, silicone also prevents heat soak, keeping intake temperatures more consistent under hard driving.
These pipes are constructed from 7-ply, wire-reinforced silicone, with an additional inner silicone layer, and have been pressure tested to over 150 PSI for extreme reliability.
Available Color Options
-
Black exterior / Blue interior
-
Blue exterior / Red interior
-
Red exterior / Black interior
Fits all S55-powered BMW M3 & M4 models
-
-
The VTT S55 crank bolt capture. slips over the head of the crank bolt fully encapsulating it, and locks it to the crank hub, meaning it cannot back out no matter what.
-
Everything needed to a successful install without having to make a trip to the dealer.
-
WHP Level supported (with proper fuel, upgrades, and tuning) Stock-800WHP VTT S55 GC Turbochargers. GC stands for "Game Changers" and that is exactly what these do! They bring a fully new casting Stainless Steel turbine manifold/housing, all new compressor housing with single piece high flow inlet, as well as our tried, and true V2 GC CHRA with a Mar-M246 GTX28 profile turbine wheel, and custom compressor wheel. These turbos have NO core charges, keep your stock turbos, sell them, hold them if you want to go back to stock, etc. The turbos will come with custom VTT silicone inlet hoses to mate up with all inlets on the market making them 100% plug, and play. There is no better, more powerful, or well thought out upgrade on the market at any price point!
-
Please note: Due to heavy increases in freight costs we have had to raise prices by $50 on 54-gallon drums, and $15 on pails.
VTT is proud to be the West Coast dealer for One Ethanol racing fuel.
We have two blends available in 5-gallon pails and 54-gallon drums. See below for descriptions of both fuels
Fuel is available for local pick up only unless you email, and make arrangements for freight shipping. Be aware fuel is considered hazmat and the freight charges are equal to or more than the fuel in all instances. Fuel CANNOT be shipped normal shipping methods such as UPS, FED EX, etc
-
Looking to maximize your F or G Series BMW for drag racing? Want to be able to dial in the perfect amount of compression or rebound on your launch? The VTT Double adjust drag shock kit is just want the doctor ordered!
-
NGK 94201 Spark Plug Set — compatible with all S58 / B58 / B48 applications, and also ideal for N54 / N55 platforms running the B58 coil upgrade.
We recommend these plugs for vehicles running 100% E85, high boost, or upgraded ignition setups. They are an excellent choice for high-performance BMW applications including N54, N55, and S55 (with B58 coils), and they also serve as a great maintenance replacement for any S58/B58/B48-powered vehicle — at a significantly better price than most options on the market.
Plugs are sold as a set of 6.
Pre-gapping is available for an additional charge -
This is for those running our brake kits that use our 11.75" or 13" Rotors that want to easily change between rotors for dedicated drag racing and street use. You can now buy Rotor/Hat Assemblies by themselves to switch between any of our 3 options
The price is for ONE ROTOR / OR ONE ROTOR/HAT ASSEMBLY
-
Racing can be rough on brake pads, if you have worn through a set of pads while using your VTT brake kit you can buy replacement pads here. Different options are available as shown below. Please take a look at your pads to see the hole orientation which will determine your pad type BP-10 pads for Dynalite calipers Single hole in the pads for the location pin - Mostly street and some racing we recommend for rear kits BP-20 pads for Dynalite calipers Single hole in the pads for the location pin - More aggressive street driving, and racing recommended for front or rear kits BP-10 pads for Dynapro calipers with twin holes in the pads for the location pins - Mostly street and some racing we recommend for rear kits BP-20 pads for Dynapro calipers with twin holes in the pads for the location pins - More aggressive street driving, and racing are recommended for front or rear kits Hawk PC (Performance Ceramic) Very Quiet, Very low dust, Hawk claims 32% increase in stopping power over stock pads. A good balance of street, and aggressive driving. Recommended for front or rear kits
MANY MORE AGGRESSIVE BRAKE PAD COMPOUNDS EXIST FROM VARIOUS MANUFACTURERS, AND YOU CAN TAILOR TO YOUR NEEDS. Y OU CAN FIND THESE BY USING THE CALIPERS STYLE NUMBERS BELOW.
6-PISTON DYNAPRO PAD STYLE 6712
4-PISTON DYNAPRO PAD STYLE 7812
-
Need to replace the gasket on your VTT Aluminum VC? Simply choose your model from the dropdowns to ensure you get the correct version.
-
VTT is proud to announce our F8X Series S55 engine catch can set up. This kit uses our already extremely popular modular catch can, and couples it with a custom CNC 6061 bracket, VTT CNC banjo fittings, VTT 5 ply silicone hose, and Push lock fittings. Installation is simple, takes about 30 minutes to 2 hours depending on your skill level, and requires removing one factory hose to install the VTT hoses. Giving an OEM fit and finish when installed. Our kit stands out from others on the market by using high-quality AN fittings, and VTT Banjo adapters. This is the ONLY catch can kit that is plug, and play with our CNC Billet Valve cover
-
Need a replacement filter for your VTT Billet Crankcase breather? You can order on here. We offer them in 3 heights, low 48mm, medium58mm, and tall 68mm. This is measured from base to top. The filter will include a new clamp. For reference: N54/55 mostly use the low A90 Supra use Medium Most Audi applications can fit a tall, but measure your filter before ordering.
-
VTT is proud to offer a Titanium hardware upgrade for all our Billet and Cast VC's. This will come with M6x30 Ti bolts N54 /N55/S55/B58 Gen 1/ B58 TU it will be an Umbrella head with a 16.3mm head. These bolts weigh half as much as comparable steel hardware and look amazing. Colors to choose from will be Burnt, Black, and Natural (silver)
-
Show off your VTT support and get a good laugh from people with our "We Like To Party" License plate bracket. Born from the infamous quote in Talladega nights
-
VTT Billet Oil Filter Housing Cap – BMW N5X / S55 / N20
VTT is proud to introduce our billet aluminum replacement for the factory plastic oil filter housing cap. Built for both performance and style, this upgrade eliminates the weak OEM plastic cap while also removing the need for a special tool during filter changes.
-
Premium Construction – CNC-machined from 6061-T6 aluminum with precision cooling fins to help reduce oil temps.
-
Factory Functionality – Retains all OEM provisions for the filter basket, including the lower pins essential for proper bypass valve function.
-
Easy Serviceability – Features a 19mm hex head for quick installation and removal with standard tools.
-
Complete Package – Includes a new sealing O-ring and small O-ring for the filter cage.
-
Color Options – Available in Red, Black, Blue, and Clear anodizing.
-
Cohesive Design – Matches perfectly with our N5X Billet Oil Cap and N5X Billet Power Steering Cap for a clean, uniform look under the hood.
-
Bundle Option – Get all three caps (Oil Cap, Oil Filter Housing Cap, and Power Steering Cap) for $175 – a 10% savings.
-
-
VTT offers silicone hoses in various Push-lock sizes, we use these for our catch can kits, but they are also suitable for coolant, vacuum, boost, etc. Do not use with fuel. We offer: -10 Push Lock 24", and 18" -8 Push Lock 24", and 19.5" -6 Push Lock 24"
-
Do you work on a lot of BMW engines from various platforms? Do you ever struggle with heavy cylinder heads, either lifting off the engine or simply moving around? Ever ruined an EXPENSIVE multi-layer head gasket while trying to install a cylinder head due to no secure way to hold it without two people? We answered yes to all of those things, and came up with a tool for anyone that works on BMWs often, and needs a way to simply, and easily remove/install, or simply move around a cylinder head. These cylinder head tools are machined from a solid billet of 6061-T6 aluminum and anodized in 4 colors for long-lasting corrosion resistance. They are knurled for a non-slip grip when oily or wet, and positioned so the head is balanced when lifting The Head Handler fits the following engines, N54, N55, S55, B58, S58 and we offer short extensions for installation with no cams/Cam ledges on the head, or long extensions for people that want to install or remove a head with cams still installed. (B58 only requires short extensions)
-
VTT Billet Power Steering Cap – BMW
VTT is proud to introduce our billet aluminum replacement for the factory plastic BMW power steering cap. Designed to eliminate the weak OEM plastic cap, this upgrade delivers both durability and style while retaining all OEM functionality, including the built-in dipstick and vent provision.
-
Premium Construction – CNC-machined from 6061-T6 aluminum, anodized in your choice of finish.
-
Factory Functionality – Full dipstick and vent hole integration, just like OEM.
-
Cohesive Design – Matches perfectly with our N5X Billet Oil Cap and N5X Billet Oil Filter Housing Cap for a complete, uniform look.
-
Bundle Option – Order all three (Oil Cap, Oil Filter Housing Cap, and Power Steering Cap) for $175.
-
Color Options – Red, Black, Blue, and Clear anodizing.
-
-
Adding a Front-facing manifold to your N54, and need to extend your map sensor harness? We got you covered with our 24" extension harness. High-quality wiring, with seating, and our own 3D printed connectors ensure a perfect fit. Fits all N54, and very early N55, please check your plug connection on your map sensor before ordering
-
Give the Gift of VTT! Looking to get your friends, or family some go-fast parts, and no idea what they need, only that they love VTT? Well, our Gift Cards have you covered! They come in $50, $100, $250, $500, and $1000 increments. Each gift card is precision cut out of plastic in the shape of the VTT logo and has the dollar amount and the code on the back. Each gift code is unique and is locked to that card. To redeem simply enter the code during check out it will remove that amount, and if you have any leftover it will go back to the card.
You can choose to have your card physically mailed to you, or a virtual card where we can send you a scan of your card.
-
Please Note: This is a Virtual Gift Card. After purchase you will receive an email with your Gift Card code
-
VTT Billet Coolant Reservoir Cap – BMW
Upgrade your engine bay and eliminate the factory plastic with the VTT Billet Coolant Reservoir Cap. This CNC-machined aluminum cap replaces the OEM plastic unit, giving you strength, style, and long-term durability while retaining all OEM functionality. Simply snap the factory pressure-relief valve into place, and you’re ready to go.
-
Premium Construction – CNC-machined from 6061-T6 aluminum.
-
Factory Functionality – Accepts the OEM pressure-relief insert for proper venting.
-
Cohesive Design – Matches our N5X Billet Oil Cap, N5X Billet Oil Filter Housing Cap, and Billet Power Steering Cap for a uniform, high-end look.
-
Color Options – Available in Red, Black, Blue, and Clear anodizing.
-
-
Unsure of the state of your CHRA's, whether brand new from a questionable source or rebuilt? Don't install them without having a proper High-Speed balance done! This is the #1 most critical factor when building a turbocharger, and is even more important for performance turbochargers or small twins that see a LOT of RPM. We use a Turbo Technics VS3 balancer, and balance most units down to under .5G Not all turbos will be able to pass a high-speed balancing test for any number of reasons (usually poor assembly, bent shaft, etc), if they will not pass, we will send you the specs they are in, and as close as we could get them. We then will give you the option to send them back, or we can disassemble, and rebuild them in-house using our other balancing, and assembly tools to ensure a properly built/balanced unit. The service is for most turbos, and we have the capability to balance most units, NOT ALL. If sending in twins please choose TWO as the quantity
UNITS MUST BE SENT IN WITH NO HOUSINGS, AND IN A CONDITION READY TO BE BALANCED, IF YOU NEED TO SEND IN COMPLETE TURBOS, WE CAN DISASSEMBLE, AND BALANCE FOR YOU, BUT AN EXTRA CHARGE WILL APPLY. IF THE UNITS ARE SENT IN A CONDITION WHERE THEY CAN NOT BE BALANCED WE WILL LET YOU KNOW THE PRICE TO GET THEM TO A STATE WHERE THEY CAN BE
-
Sale!Looking for a Lightweight, AFFORDABLE drag pack that looks amazing for your BMW, Toyota, or VAG platform? Look no further! VTT is proud to announce our lineup of Drag pack wheels for various BMW/Toyota/VAG fitments! We teamed up with Rota and had them open custom molds for us of their extremely popular Grid design. With these molds, we have an exclusive on 15X10, 17X10, and 17X4.5 wheels in our exact specs. The wheels are currently offered in the colors and sizes below
A variety of Offsets are available, as well as spacers here - VTT Spacers can be found here - https://vargasturbo.com/product/vtt-billet-wheel-spacers/
As well as Center bore adapters here - https://vargasturbo.com/product/vtt-billet-hubcentric-wheel-bore-adapters/Wheels are priced EACH, meaning per wheel
PLEASE NOTE! CHECK FITMENT CAREFULLY. ANY WHEELS THAT HAVE HAD TIRES MOUNTED OR ARE DAMAGED DURING TEST FITTING ETC ARE NOT RETURNABLE!
We make NO CLAIM these fit ANY PLATFORM, or ANY factory brake set up. It is YOUR JOB to measure, and make sure they will fit BEFORE you mount tires or install them. WE NEVER suggest shaving down brake calipers to fit a smaller wheel. If they do not fit. GET A SMALL BRAKE KIT!
Colors offered:- Satin Black
- Gloss Black
- Bronze,
- Gun Metallic
- 15x10 ET45/ET40 (wheel weight 16 lbs)
- 17x10 ET45/ET40/ET25 (wheel weight 19lbs)
- 17x4.5 ET-20 (wheel weight 16 lbs)
- 15x10 ET45 - (wheel weight 16 lbs)
- 17x10 ET45/ET40/ET25 (wheel weight 19 lbs)
- 17x4.5 ET-20 (wheel weight 16 lbs)
-
Everything needed to a successful install without having to make a trip to the dealer.
-
VTT “GC-MAX” Turbocharger Upgrade – BMW S55 (Twin Turbo)
Supported Power Level (Stock Engine): Up to 1000WHP
Base Architecture: Twin Garrett G25-660 Spec
PTE Style Wheel Designation (Comp/Turb): 67/54
Overview
VTT takes the S55 platform to the next level with our “GC-MAX” evolution of the record-setting GC Series. Based on everything learned from the GC / GC+ programs, GC-MAX pushes the limit of what is possible while retaining full bolt-on, factory-location packaging.
Internal flow paths have been enlarged significantly. A/R is optimized. Inlet diameter is maximized to 2.5”. Compressor is increased to 67mm. Most importantly — the turbine housing has been completely retooled to accept our 54mm G25-series turbine wheel used on the G8X S58 GC+ and F9X GC series. This turbine is the key to GC-MAX power — extremely low backpressure, rapid spool, and capability far beyond any turbine wheel of similar size.
This same wheel architecture has already pushed 1000WHP+ on S58 / S63 based applications — and has gone 9.44 @ 146mph on a stock motor / stock drivetrain G80. GC-MAX gives the F8X owner a true bolt-on 1000WHP solution without going single turbo and without losing factory response, packaging, or reliability.
-
Looking to make sure all metal contaminates that are possibly in your oil are not circulated? VTT has you covered with our Titanium Magnetic oil drain plugs for BMW, and any other vehicle that uses an M12x1.5 drain plug. This drain plug will capture any ferrous metal particles in your oil, and capture them to be cleaned during your next oil change. It also is stronger than a Steel or Aluminum drain plug, and looks cool! These are made from GR5 Titanium and use a rare earth magnet to capture metal particles in your oil... Kit includes:
- 1 Titanium Drain Plug
- 1 M12 Crush Washer
-
Are you looking to make your F8X Series BMW faster in the 1/4 mile or 1/2 mile racing? Want to run 17" wheels in the front? Want to drop close to 50 lbs of unsprung weight off the front of your F8X M2C/M3/M4 at the same time? Do not want to break the bank while doing so? Look no further than the VTT F8X Series BMW Ultimate Lightweight Front Brake Kit! This kit will allow you to run the wheel/tire combo you need to drop your ETs all while putting the car on a significant diet over the stock front brake setup. The kit is a true plug-and-play kit using Custom VTT parts, coupled with DOT-approved brake lines, CNC 7075 rotor hats/brackets, and a CEL eliminator harness for the brake sensor. This kit comes in 1 variation, with two different caliper Options. We HIGHLY suggest 6-piston Calipers for street driving and 1/2-mile racing. These calipers will drop weight, AND be a braking upgrade over stock calipers.
Pictures are for REFERENCE ONLY. All kits will come with varying hardware, brackets, and mounting styles based on the platform.
-
Looking to adapt your wheel bore size to a smaller hub bore? VTT has you covered with our hub-centric adapters. These adapters are made from Billet 6061-T6 aluminum, and anodized in black. We have these sizes currently
- 57.1mm hub to 60.1mm wheel bore
- 57.1mm hub to 64.1mm wheel bore
- 57.1mm hub to 66.1mm wheel bore
- 57.1mm hub to 66.6mm wheel bore
- 57.1mm hub to 67.1mm wheel bore
- 57.1mm hub to 70.3mm wheel bore
- 57.1mm hub to 71.6mm wheel bore
- 57.1mm hub to 72.6mm wheel bore
- 57.1mm hub to 73mm wheel bore
- 57.1mm hub to 74mm wheel bore
- 57.1mm hub to 74.1mm wheel bore
- 64.1mm hub to 72.6mm wheel bore
- 66.6mm hub to 72.6mm wheel bore
They are sold in sets of two, order TWO SETS for a full car, or one set per axle.
-
VTT is proud to offer PTE Turbocharger products! Please Note: All Precision Turbos have a 2-3 week shipping time
-
VTT Carbon Fiber Driveshaft for BMW Applications
Why overpay for a carbon fiber BMW driveshaft?
VTT is proud to offer a premium carbon fiber driveshaft manufactured exclusively for VTT in the USA by GCDS (Gulf Coast Driveshaft) — one of the premier driveshaft manufacturers in the country with extensive experience in high-performance and drag racing applications.
Each driveshaft is constructed using 3.31" carbon fiber tubing, paired with NEAPCO Performance 1350 series U-joints, then bonded using a proprietary high-strength process and precision balanced to within 1/8 in-oz as a complete assembly.
Every shaft is torque tested in-house prior to shipping to ensure proper bonding and structural integrity. GCDS and VTT are among the few manufacturers that perform full torque testing on each shaft before it leaves the facility.
To complete the system, the driveshaft is paired with VTT-designed 7075 aluminum adapters, eliminating the factory guibos and unnecessary flex points. The shaft connects directly to the BMW 3-bolt front flange, while a VTT 4340 rear adapter replaces the factory slip-in / screw-retained shaft design for improved strength and reliability.
Proudly Made in the USA.
PLEASE NOTE! YOU MUST SEND US YOUR VIN NUMBER TO PROPERLY PROCESS YOUR ORDER, IF YOU DO NOT SEND YOUR VIN, YOU ORDER IS GOING TO BE HELD
PLEASE NOTE! Driveshafts can have UNUSUALLY LONG LEAD TIMES. We hope to reduce this with GCDS, but if the shaft shows OUT OF STOCK, expect a lead time of 4–8 weeks, unless we specifically state that it can ship sooner.
Due to the nature of these shafts being manufactured by a 3rd party, ANY ORDERS PLACED FOR VTT CF DRIVESHAFTS ARE 100% FINAL.
NO REFUNDS. NO CANCELLATIONS. FOR ANY REASON.
THIS INCLUDES LONG LEAD TIMES.
PLEASE ORDER CAREFULLY. ONCE THE ORDER IS PLACED, IT IS FINAL.
-
Building a kit using Mac solenoids to control boost? Need an easy way to mount it? VTT-FAB has you covered with our billet Mac Solenoid brackets. Machined from 6061 billet and anodized in 3 colors, these are the perfect way to mount your Mac valve and look good while doing it. Each kit includes:
- One Mac Solenoid bracket (3-Port or 4-Port)
- 2 Allen screws to hold the valve to the bracket
- M6 Mounting Bolt
-
Need a Tee fitting for plumbing Vacuum, or Boost lines, Don't want to use cheap plastic ones that can get soft when hard, and brittle after they heat cycle? We didn't either, which is why we machined these high-quality billet tees to solve this issue. Machine from 6061-T6 aluminum, and anodized in black for a long-lasting corrosion-free finish, these tees look great, and will you never have to worry about one failing. We offer them in two sizes, each size has 12mm legs and 3 barbs:
- 7.60mm / -4 Push Lock for people looking to use -4 push lock hose or -4 AN hose. This is a perfect fit for those.
- 1/4" For people looking to use 1/4" vacuum tube
-
Looking to convert your 5×120 or 5x112 vehicle to 5x114.3 wheels, or 5x120 wheels, and open up your wheel options DRAMATICALLY? We got covered with our VTT wheel spacer conversion kits. These kits are machined from billet 6061-T6 aluminum and anodized for a long-lasting finish. We then press in 10.9 class studs, with corrosion-resistant zinc coating for years of use. The spacer then accepts either a 5x114 wheel or a 5x120 wheel. The 5x114 use M14 studs, and the 5x120 use M12 studs. All the spacers have either a 66.6mm or 72.6mm Hub bore size to fit 99% of BMW applications.
QTY 1 is for ONE SPACER. If you need to do 4 wheels order FOUR!
We offer Hub-Centric adapter rings to fit other wheel bore sizes No wobble bolts or redrilling here. We offer these in 4 thicknesses 15mm, 17.5mm, 20mm, and 25mm. The studs coming out of the spacer are 40″ total length and come with Black Lugnuts. Spacers that convert to 5x120 have M12 studs, ALL others have M14x1.5 -
Looking for Mac solenoids for your build? We got em here at VTT-FAB so you can get everything in one place. We have 3-port, and 4-port in stock!
-
Need to move your coolant expansion tank to the other side of the vehicle for a single turbo kit you are building, extend Map sensor plugs, or IAT, how about Throttle Body? Don't cut your factory wires. Just get a VTT-FAB extension harness, and plug and play! These come in various lengths and are covered in expanded sheathing with heat shrink on both ends for a long-lasting, good-looking finish. Available:
- Coolant Extension for late model BMW 2015+ 5 ft
- Pre-Throttle Map sensor extension harness 2 ft
- Pre-Throttle IAT Sensor extension harness 2 ft
- B58/S58/B48 etc Throttle body extension harness 2 ft
- B58 to S55 Throttle conversion/extension harness 2 ft
- EWG Actuator Extension harness, Various Lengths
- N54 stock MAP to N20 Map sensor extension
-
VTT is proud to offer a truly plug-and-play line lock kit for select BMW vehicles that does NOT require running wiring inside the car, mounted switches, holes in the dash, etc. Our newly designed and released line lock kits use a 40amp wireless remote control switch with 4 different modes that allow you to tailor your line lock setup exactly as you prefer. You simply install the solenoids, install the harness with the switch which has all the wiring terminated, bleed the brakes, and you are ready for effortless burnouts which will not be interfered with by the DME because you are holding the brakes, nor wear your rear brake pads. You can store the remote anywhere in your vehicle, center console, cup holder, door cup holder, etc., and when you need to do a burnout to heat your race tires it's in arm's reach without running any wiring into the vehicle. Fitment is confirmed for G8X M3/4, A9X Supra - The kit itself including lines, solenoids, etc will fit most all late model BMW Chassis including F8X, F3X, G2X, etc. The main concern will be mounting the wireless switch in the passenger cowl area. The kit includes:
- Line lock solenoids with weather pack connectors
- Two Parker 90-degree -3 an fittings
- Two Stainless Steel adapter fittings
- Two DOT Approved Stainless Steel brake lines
- One complete wiring harness
- One Remote control switch with TWO remotes
-
Looking to keep the underhood heat down on your single turbo car, or build? We got you covered with our VTT-FAB Carbon Fiber Turbo Blankets. The outer shell is made of Carbon Fiber, and the inner shell is Silica Fiber. For 2500F intermittent / 1800 direct heat rating. We have them in 2 sizes T3, and T4. See fitment below Kit included:
- 1 Carbon Blanket of choice
- 2 install springs
-
VTT is happy to offer our very unique and universal billet mount to fit any roll bar or cage with 1.5", 1.75", or 2" diameter tubing. These mounts are designed from 6061-T6 aluminum and are made to SECURELY hold a JBL Flip version 3 - Version 6 and allows you to bring music into your race car, off-road vehicle, rock crawler, boat, basically anything that has a length of tubing this will allow you to have an easy way to have tunes without having to install and mount a stereo system. They can also be used as a single mount to hold things such as a helmet, steering wheel, or anything you want to quickly hang for easy access once seated. For the JBL flip you will need TWO mounts, simply install them loosely, snap in your JBL Flip to get the proper spacing, and tighten down. The device is then securely mounted and can be removed easily. We offer these in a variety of anodized colors for a long-lasting durable finish including Black, Red, Blue, Clear, Orange, and Green Mounts are sold individually Features:
- Billet 6061-T6 Aluminum construction anodized in a variety of colors
- Can be used to SECURELY mount a JBL Flip 3-6 to anything that has a length of 1.5", 1.75" or 2" tubing
- Can also be used as a universal mount for anything you need to hang in your race car, off-road vehicle, etc
- Completely reversible, and can be moved from vehicle to vehicle
-
VTT F8X Ultimate Lightweight Rear Brake Kit
F87 M2 / F80 M3 / F82–F83 M4
Looking to make your F8X M2C/M3/M4 faster in the 1/4-mile or 1/2-mile?
Want to run 17” rear wheels?
Want to retain the factory parking brake while dropping significant unsprung weight?
The VTT F8X Ultimate Lightweight Rear Brake Kit is engineered for straight-line performance while maintaining proper street functionality. This kit allows you to run the wheel and tire combo needed to lower ETs — all while putting your F8X on a serious weight reduction program compared to the factory rear setup.
✔ 17” rear wheel clearance
✔ Retains stock parking brake
✔ Up to 21 lbs total rear weight savingsThis kit comes in 1 variation, with two different caliper options. We HIGHLY suggest 6-piston Calipers for street driving and 1/2-mile racing. These calipers will drop weight, AND be a braking upgrade over stock calipers. Requires trimming of dust shields to fit
Pictures are for REFERENCE ONLY. All kits will come with varying hardware, brackets, and mounting styles based on the platform.
-
VTT is proud to offer its very own Game Changer S55/N55 to B58 Coil conversion kit for the BMW S55/N55 platforms. The 55 series of engines has notoriously had ignition problems with the factory coils, while aftermarket upgrades do exist, they can be bulky. The solution is the BMW B58 ignition coils which are extremely robust and can support well over 1000WHP with no issues. This means a plug-and-play affordable solution that fits like stock, and looks AMAZING doing so! We designed our own 6061-T6 Billet bracket in a plethora of colors including matching shades for every S55/N55 Valve Cover. This means you can mix and match the color of the bracket with coil color, with VC color to truly tailor your engine bay to look exactly how you want it to!
Note: Flash setting changes may be required when installing the conversion kit to ensure the proper function of the B58 coils with S55/N55 DME. This can be found in almost all flashing software settings such as MHD, Bm3, etc.
-
VTT Universal Turbo Fittings – Oil & Coolant Solutions for BMW Turbo Builds!
Looking to fabricate your own turbo kit for BMW platforms? Need an easy solution to block off water lines or create custom feed and drain fittings? Look no further! VTT offers a wide range of high-quality oil and coolant fittings to simplify your build. Our fittings are designed for most late-model BMW platforms, providing a plug-and-play solution for custom turbo setups. 📌 Available Fitting Options: 🔹 Oil Feed – -4 AN Male 🔹 Oil Drain – -10 AN Male 🔹 Coolant Fittings – Barbed Male or Block-Off Options -
Looking to convert your 5x112 M14x1.25 BMW vehicle to 5x114 to open up your wheel options? Want to drop 60% of the weight off steel options? We got covered with our VTT TITANIUM wheel stud conversion kits. These kits are Grade 5 Titanium studs, rated at more than 135,000PSI Tensile Strength, with Grade 5 Titanium nuts with a 60-degree cone seat to fit most all aftermarket wheel applications and convert your vehicle to M12x1.5 wheel studs which allow you to fit 5x114 wheels with no other changes.
PLEASE NOTE – THESE STUDS WILL ONLY WORK IF YOUR WHEELS ARE DRILLED M14 THESE WILL NOT WORK FOR WHEELS DRILLED M12!
DO NOT USE ANY HUB-CENTERING SLEEVES WITH THESE CONVERSION STUDS, THE LUGS WILL CENTER THE WHEELS. THE USE OF A CENTERING SLEEVE MAY LEAD TO STUDS BREAKING. FOR INSTALLATION YOU MUST SNUG EACH LUB UP SLOWLY, AND IN A STAR PATTERN TO GET THE WHEEL CENTERED ON THE LUGS, FAILURE TO DO SO CAN ALSO LEAD TO FAILURE.
-
Are you building a single kit for the N54, N55, or S55 platform? The stock studs are usually a little bit short for most single-head flanges, and finding M7 studs is not easy. So we made our own longer studs to combat the issue. Made from 10.9 grade steel, and coated in black oxide, these are the perfect solution to the short stud problem. Sold individually so order the number you need. Stud details are as follows
- Overall length 47mm (stock 39mm)
- 3mm shoulder
- 6mm head which is 5mm hex
- 14mm short end
- 24mm long end (stock 15mm)
Dont forget our M7 copper lock nuts as well to complete the job - https://vargasturbo.com/product/vtt-fab-m7-copper-locking-exhaust-nuts/
-
Are you building a single kit for the N54, N55, or S55 platform? M7 Locking exhaust nuts is not easy. So we made our own to combat the issue. These are the perfect solution to the problem of hard-to-find M7 lock nuts. Sold individually so order the number you need.
Note: This is nuts ONLY Stud not included, by our extended M7 studs here - https://vargasturbo.com/product/vtt-fab-extended-m7-n54-n55-s55-b58-2-port-head-studs/
-
Looking to replace your damaged factory BMW Actuator part number - 11658691853 VTT has located and ordered in bulk these actuators, and offer them at a discounted price. These are 100% FACTORY BMW OEM actuators, not aftermarket. Fitment is for the following, but they work to replace basically any BMW Actuator.
-
Have a problematic PCV on your S55/N55 powered BMW, don't want to pay to replace the entire VC? The VTT PCV delete kit is just what you need. This kit blocks the factory PCV from pulling from the head ports, gets rid of the tear-prone rubber diaphragm, and essentially converts your VC into VTA through the factory front port on the VC. This kit can work stand-alone with the cap, and a -10 ORB plug, can be used to run an extra breather port, or it can be installed with any Catch Can kit that uses the front port of the stock VC. Simply remove the factory cap, take out the diaphragm, screw the plug into the center port, and tap the new cap on with a soft blow hammer or similar. This deletes the PCV and allows you to avoid the issues of a failed diaphragm. Kit Choices
- Cap and -10ORB plug only (to be used with an existing catch can or VTA)
- Cap and Catch can kit (recirc or VTA) Complete kit to delete the PCV, and run a catch can (Currently works with S55 only)
- Cap Only (To be used if routing an additional hose from the cap to location or set up of choice, requires your parts to work)
- 1 PCV Cap
- 1 PCV port block off Plug
- 1 -10 ORB Plug
- Optional Catch Can kit
-
Are you looking to fab up your own S55 Single kit, but want our game-changing factory control via Turbosmart Straight gate? Yep, we offer that. This manifold is fully fabricated in-house using 321 1.25" Sch 10 Weld els, our own wire cut flange, and cast 6 into 1 Collector. We also fab the Turbosmart straight gate port which will provide perfect fitment for our factory-controlled setup. this manifold is designed to work with T3 V-Band inlets such as Garret G25, G30, G35, PTE T3 Size V-band inlet turbos, and Turbosmart T3 V-Band inlet turbos. This kit will require the use of our VTT-FAB Factory controlled External Straight gate set up, which can be purchased separately, and can be added from the drop-down. Features:
- Fully Fabbed in-house in Hayward Ca using US-sourced parts
- All Tig Welded
- 6 into Cast Collector that fits most T3 Small Frame Style V-band flanges (choose turbo chose from the drop-down)
- Fully set up for our VTT-FAB factory-controlled turbo smart straight gate. Making this plug-and-play with your existing tuner
- 321 Stainless Weld Els for the ultimate in heat resistance and durability
- 1.25" Primary for lightening spool, and high exhaust gas velocity
- Works with VTT-FAB Fitting adapters
THIS IS THE MANIFOLD ONLY! WE DO NOT SELL DOWNPIPES, CHARGE PIPES, ETC. SEPERATELY. THIS WILL REQUIRE YOU TO FAB UP ALL OF THOSE THINGS TO MAKE THIS WORK. IF YOU CANNOT DO THAT WE SUGGEST BUYING THE COMPLETE KIT...
-
VTT-FAB Top-Mount Single Turbo Kit
For BMW F8X S55 Platform
VTT-FAB is proud to offer the premiere top-mount single turbo kit for the BMW F8X S55 platform. This system is 100% made in the USA at our Hayward, CA facility using only premium materials and components.
The heart of the kit is a hand-fabricated 321 stainless manifold with billet flanges for maximum flow and long-term durability. It’s paired with our factory-controlled external wastegate system featuring a Turbosmart 60mm Straight Gate. This design gives you complete wastegate control directly through your factory ECU tune — no external boxes, MAC solenoids, or vacuum lines required. Simply reuse your factory actuator with our adapter, and you have a true boost range from 0 PSI to the limits of your turbocharger.
⚠️ Important Notes
-
Please email [email protected] to confirm current build times.
-
Every kit is built to order and cannot be canceled once fabrication begins.
-
-
VTT is proud to offer our EWG "Direct Control System" or DCS! This is a completely new innovation for people looking to control the highest-flowing wastegate on the market using an existing BMW electronic actuator. This system will allow BMW owners who have a vehicle with Electronic Wastegates from the factory to utilize this system to control an externally wastegated turbo system, AND it will ALSO allow ANY vehicle to use this setup to control your own custom turbo system. This is done by utilizing our custom 7075 Billet aluminum bracket coupled with a Turbosmart Straight gate, and if needed an EWG controller made for us by DCCD Pro. This allows direct external wastegate control over any turbocharger system with or without EWG for the factory. Features:
- Utilizes the most current wastegate technology the Turbosmart Straight Gate. This gate allows maximum flow with minimal restriction, low drive pressure, and much more. Full details can be found here - https://www.turbosmart.com/product/electronic-straightgate-esg50-external-wastegate/
- Can be configured in multiple ways, and angles based on how you mount the adapter
- The adapter is 7075 Aluminum which has the strength of steel and weight of aluminum
- All connection fittings, are made from Nitronic 60 which has extremely high temperature and wear properties
- Zero Drive Pressure, no springs, no poppet valves, direct control over the gate using factory ECU logic
- Adaptable to ANY turbo system on any car to provide the ultimate in boost control!
-
PFS is proud to offer a true drop-in LPFP for S55-powered BMWs. This LPFP needs NO additional pumps, wiring harnesses, controllers, etc. Capability is 850whp on E85 and up to 1000whp on race fuel. We start with a factory bucket, we modify it to accept our high-flow brushless fuel pump. We then re-terminate the factory wiring to accept the new pump. No wiring splices, done the same way the factory does -the right way. Every pump is fully tested on our flow bench to ensure proper function before shipping -you're going to be installing a product that has already proven itself. This pump is a true drop-in meaning you pull the factory unit out, install this pump, plug the factory plug into the hat, and you are done. The stock ECU controls the pump fully, and NO tune changes are required to take advantage of it. Installation is easy for the DIY'er, and if you use a performance shop it'll be easy for them -just tell them to remove the old and replace it with new same as factory pump.
-
Looking to remove your BOV either for leak testing, or dont want to run one, and your charge pipe or housing has a flange on it. You can use this billet plate to block off the BOV flange. Uses the O-ring from the BOV to seal, and removes the BOV. Fitment: Tial BOV Turbosmart BOV with female flange like Tial
-
Looking to up your boost limit on just about any BMW vehicle that runs a 3 or 4-wire BMW map sensor including but not limited to S58, B58, N54, N55, S55, S63, B48, B47, B42, B57, B46? We were too, so we decided to make a very easy plug-and-play kit for 3, and 4-wire BMW map sensors. These kits will allow you to completely replace the 3-wire sensor with one of our sensors, leave your stock 4-wire in place for IAT sensing, and move the power, ground, and sensor signal from the factory sensor to our sensor. These sensors have the proper scaling which will allow your tuner to simply change your map sensor scaling in the tune, and the factory ECU will be able to utilize the sensor voltage with no problem. We are offering these in 5 bar (58 psi), and 6 bar (72 psi), and each comes with a plug-and-play harness, and optional fittings for ease of installation.
Note: For the S58/B58 our Factory style Pre-Throttle map sensor is also 5 bar, and will work fine coupled with the post throttle kit, but the scaling is different, if you want matching Voltages Pre/Post throttle you can run two of these.
A variety of install pics can be found below and - Here
Scaling PDF Links: 5-Bar / 6-Bar
Features include:- Plug and Play harnesses with no wire splicing
- Output wire for connecting a PI or external controller to your post-throttle map sensor for the most stable signal that is not affected by throttle closure
- Different fittings are available for your plumbing needs.
- Can have matching voltage signals for pre/post throttle for ease of tuning, and boost reference
- B58/S58 etc Pre Throttle - 3 Wire Harness (Charge pipe to 1/8" NPT adapter needed, for B58/S58 90 degree adapter needed to provide sensor clearance)
- B58/S58 Post Throttle - 4 Wire Harness (Boost reference will be needed from manifold to sensor)
- F90 M5 Pre/Post Throttle - 4 Wire Harness (May need to repin) (Boost reference will be needed from manifold to sensor)
- Most all other platforms Pre/Post Throttle - 4 Wire Harness (May need to repin) (Boost reference will be needed from manifold to sensor)
- B58
- S58
- S63/ S63TU
- N63
- N54
- S55
- N55
- N20
- B46
- B48
- B57
- B47
-
Sale!
VTT x PFS EBS (External Brushless System) Fuel System
VTT, in collaboration with Performance Fueling Solutions (PFS), is proud to introduce the PFS EBS — External Brushless System.
The EBS is a fully stand-alone, next-generation brushless fuel system available in both platform-specific and universal fitments. Built around state-of-the-art Protec brushless pump technology, this system is capable of supporting up to 2,500 HP on ethanol-based fuels — and even more on gasoline or ethanol blends.
With its compact 15" x 10" footprint and ultra-lightweight construction, the PFS EBS is engineered for performance without compromise. The complete system — including pumps, surge tank, FPR, controllers, and wiring harness — weighs in at under 10 lbs (dry), thanks to a carbon fiber mounting plate and carefully chosen lightweight materials.
EBS Bench Testing Video:
EBS Bench Test Video -
We have a variety of fittings in stock to help you get your turbo system plumbed up! Available are:
- 1/8" NPT to -6 AN Male (Great for water lines, or anywhere you need a small 1/8" NPT to -6 Male AN)
- M14x1.5 to -6 AN Male (Great for water lines on Garrett turbos GT, GTX, and G-Series, or anything that has a metric M14x1.5 thread and you need a -6AN male)
- .035" Turbo feed restrictors. These are for Garrett turbochargers and will fit GT, GTX, and G- Series up to G35
- Garret GT, GTX, and G-Series up to G35 -8 An drain adapter. For those that want a low profile -8 drain for their GT-G-Series Garrett. (Comes with two bolts, and a gasket)
-
VTT S55/N55 EWG Cast Aluminum Valve Cover
VTT is proud to introduce our S55/N55 EWG Cast Aluminum Valve Cover, designed for performance-driven BMW owners looking for a durable, stylish, and functional upgrade. This option provides a cost-effective alternative to our billet valve cover while still delivering enhanced engine bay aesthetics and eliminating the failure-prone factory plastic cover, which can crack over time.
Beyond durability, this valve cover removes the problematic factory PCV system, giving you complete control over how you set up your PCV. We highly recommend pairing it with a catch can for optimal performance. Additionally, this cover is perfect for single turbo conversions, offering increased clearance and improved heat resistance.
-
VTT is proud to be an authorized reseller of Race Tech Seats. These are the premiere seats for your drag build or road race car. See Specs/Features below
-
VTT is proud to be an authorized reseller of Race Tech Seats. These are the premiere seats for your drag build or road race car. See Specs/Features below
-
VTT is proud to be an authorized reseller of Race Tech Seats. These are the premiere seats for your drag build or road race car. See Specs/Features below
-
VTT/PFS Stainless Steel Fuel Strainer for Walbro In-Tank Pumps
The fuel system is one of the most critical components of your entire build—it delivers the fuel that translates into big power and fast times! Without proper filtration, your Walbro 274, 285, or 295 fuel pump can ingest contaminants, leading to premature failure. However, choosing the right strainer or pre-filter is just as important as post-filtration. 🚨 Why Does Your Fuel Pump Need the Right Strainer? ✅ Too fine of a filter can restrict flow and cause the inlet to collapse. ✅ Too coarse of a filter can allow debris to pass through, damaging the pump and engine. ✅ Low-quality materials can break down, collapse, or cause fueling issues—leading to potential engine failure.The VTT/PFS Stainless Steel Fuel Strainer – The Ultimate Solution
-
Secure Your AN Fittings the Right Way – Without the Damage
VTT now offers a complete line of precision Billet 6061-T6 Aluminum AN Wrenches, designed to grip without marring your fittings. Whether you're working with -3 or -20 AN sizes, we've got you covered.These wrenches are lightweight, durable, and anodized in 8 vibrant colors for a long-lasting finish and easy size identification.
Available Options:
-
Full Kit: Includes all sizes from -3 to -20
-
Common Size Kit: Includes -4, -6, -8, -10, and -12
-
Individual Wrenches: Purchase only the sizes you need
-
-
Product Release: VTT Billet Installation Dowels
Ever tried wrestling a BMW transfer case into a car on your own? Or struggled to line up a transmission or subframe as you're sliding it into place? If you have, you know just how tedious—and downright frustrating—it can be.
After doing these installs hundreds of times, we used to rely on cut-off factory bolts to help guide components into place. But cutting bolts for different applications turned out to be a hassle—time-consuming, inconsistent, and often not long enough to provide the guidance needed.
So we created a better solution: VTT Billet Aluminum Installation Dowels—designed specifically to make these installations easier, faster, and more accurate.
Key Features:
-
One universal length: 6 inches
- Bull nose for easy slip into the part being installed
-
Two thread sizes
-
Three thread pitches
-
Built-in 5mm hex in the end for easy install and removal
Available Thread Options:
-
M10 Standard Pitch – Ideal for BMW transfer case installs and more
-
M12 x 1.5 Fine Thread – Perfect for most BMW front and rear subframe installations
-
M12 Standard Pitch – Designed for BMW transmission installs
-
-
VTT -16 Billet HIGH-FLOW Catch Can System
Maximum Venting for Maximum Power
VTT is proud to introduce our -16 Billet High-Flow Catch Can System — designed from the ground up for high-horsepower applications requiring serious crankcase ventilation. Whether you're pushing over 900WHP or beyond 2000WHP, this system delivers unmatched performance, reliability, and engine bay cleanliness.
Key Features:
-
Supports -16 AN lines (with optional -12 or -20 fittings)
- 20 Fluid OZ capacity
-
Engineered for big-power builds needing high crankcase pressure relief
-
Triple-stage filtration system to eliminate oil mist — even in the event of engine failure
-
Designed, tested, and proven to keep oil inside the catch can — not in your engine bay
Triple Filtration Technology:
-
Stage 1 - Stainless steel filter – captures 95% of oil mist on entry
-
Stage 2 - Perforated diffuser plate – further disperses and slows down airflow
-
Stage 3 - Final stainless mesh layer – scrubs out any remaining vapor before venting
This advanced system has been tested with over 200 PSI of pressure and more than half a quart of oil without releasing a trace of oil mist. As long as the catch can is properly serviced and not overfilled, even catastrophic engine failure won’t result in a mess under your hood.
Application-Specific Kits Available:
We offer plug-and-play kits for popular platforms, including:
-
G8X M2/M3/M4 (S58) SINGLE TURBO ONLY
-
F9X X3M/X4M SINGLE SINGLE TURBO ONLY
-
A9X Toyota Supra
Each Plug and play kit includes everything needed for installation: catch can, vehicle-specific bracket, fittings, hoses, and optional drain. Again, plug-and-play kits include ALL required parts. Bracket, fittings, line, etc. No additional fittings are required except the drain if wanted.
-
-
VTT B58/S58 Head Port Block-Off / Built Check Valve Kit
The VTT B58/S58 Head Port Block-Off / Check Valve Kit is designed to either seal off or convert the factory head ports used by the OEM low-side PCV system. These ports in the cylinder head utilize engine vacuum to evacuate crankcase gases — but in the process, can allow oil to enter the intake manifold, leading to valve carbon buildup and other performance issues over time.
This kit provides two configuration options:
-
Block-Off Version – Completely seals the factory head ports to prevent oil intrusion and unwanted vacuum leaks.
-
Billet Check Valve Version – Converts the head ports into a robust internal PCV system using precision-engineered check valves. These one-way valves allow vacuum to function as intended while blocking boost pressure from entering the crankcase or charge tract.
By bypassing the factory PCV valve in the valve cover, the VTT kit replaces it with an improved three-valve internal system integrated directly into the cylinder head. This design improves reliability, simplifies plumbing, and ensures consistent crankcase pressure management — critical for both stock and high-performance B58/S58 applications. This kit does NOT require any tapping, meaning no metal to get into the engine etc. You simply tap the plugs or check valves into place.
Key Features
-
Eliminates oil draw-through into the intake manifold
-
Prevents carbon buildup on intake valves
-
Converts to an internal, head-integrated PCV system
-
Utilizes precision-machined check valves for boost sealing
-
Fully reversible — Block-offs or valves can be removed if needed
- No tapping is required. Easy install, by tapping the blocks or valve into place.
-
-
Glass in your VTT Catch Can broken? If so we have replacements avaialble for $10 each. These are direct replacements for the glass that came with your cans.
