- Need a Tee fitting for plumbing Vacuum, or Boost lines, Don't want to use cheap plastic ones that can get soft when hard, and brittle after they heat cycle? We didn't either, which is why we machined these high-quality billet tees to solve this issue. Machine from 6061-T6 aluminum, and anodized in black for a long-lasting corrosion-free finish, these tees look great, and will you never have to worry about one failing. We offer them in two sizes, each size has 12mm legs and 3 barbs:
- 7.60mm / -4 Push Lock for people looking to use -4 push lock hose or -4 AN hose. This is a perfect fit for those.
- 1/4" For people looking to use 1/4" vacuum tube
-
Secure Your AN Fittings the Right Way – Without the Damage
VTT now offers a complete line of precision Billet 6061-T6 Aluminum AN Wrenches, designed to grip without marring your fittings. Whether you're working with -3 or -20 AN sizes, we've got you covered.These wrenches are lightweight, durable, and anodized in 8 vibrant colors for a long-lasting finish and easy size identification.
Available Options:
-
Full Kit: Includes all sizes from -3 to -20
-
Common Size Kit: Includes -4, -6, -8, -10, and -12
-
Individual Wrenches: Purchase only the sizes you need
-
-
VTT/PFS Stainless Steel Fuel Strainer for Walbro In-Tank Pumps
The fuel system is one of the most critical components of your entire build—it delivers the fuel that translates into big power and fast times! Without proper filtration, your Walbro 274, 285, or 295 fuel pump can ingest contaminants, leading to premature failure. However, choosing the right strainer or pre-filter is just as important as post-filtration. 🚨 Why Does Your Fuel Pump Need the Right Strainer? ✅ Too fine of a filter can restrict flow and cause the inlet to collapse. ✅ Too coarse of a filter can allow debris to pass through, damaging the pump and engine. ✅ Low-quality materials can break down, collapse, or cause fueling issues—leading to potential engine failure.The VTT/PFS Stainless Steel Fuel Strainer – The Ultimate Solution
- Show off your VTT support and get a good laugh from people with our "We Like To Party" License plate bracket. Born from the infamous quote in Talladega nights
- Tired of your Dragy flying all over the car as you try to do runs? Tired of low sats or no sats warning due to improper location of the Dragy in the vehicle? Well say goodbye to those issues with our new Carbon Fiber and Plastic Dragy holders. These are made from either 100% Pre-Preg Carbon Fiber, or molded plastic for a perfect fit. The carbon fiber gives it just the right look to add to your performance vehicle! Each holder has dual Suction cups and will stick to any smooth surface. We suggest mounting them in the upper left or right corner of your windshield with a full view of the sky. Dragy holder features
- Stop your Dragy from flying off the dash, and having to search for it
- Position your Dragy in the optimal position for the best satellite coverage
- VTT Dragy holder exposes the entire top of the Dragy so nothing is blocking the receiver from the Satellite
- The charging port is not blocked and can be accessed with the cover on
- Choose from REAL Carbon Fiber or Molded Plastic
- VTT CNC Billet check valve that can be used for a variety of uses including a vacuum/boost check valve when removing the stock PCV system, and still wanting to run vacuum to the crankcase. Rated at over 100 psi, with a cracking psi of .25psi.
- VTT is happy to offer our very unique and universal billet mount to fit any roll bar or cage with 1.5", 1.75", or 2" diameter tubing. These mounts are designed from 6061-T6 aluminum and are made to SECURELY hold a JBL Flip version 3 - Version 6 and allows you to bring music into your race car, off-road vehicle, rock crawler, boat, basically anything that has a length of tubing this will allow you to have an easy way to have tunes without having to install and mount a stereo system. They can also be used as a single mount to hold things such as a helmet, steering wheel, or anything you want to quickly hang for easy access once seated. For the JBL flip you will need TWO mounts, simply install them loosely, snap in your JBL Flip to get the proper spacing, and tighten down. The device is then securely mounted and can be removed easily. We offer these in a variety of anodized colors for a long-lasting durable finish including Black, Red, Blue, Clear, Orange, and Green Mounts are sold individually Features:
- Billet 6061-T6 Aluminum construction anodized in a variety of colors
- Can be used to SECURELY mount a JBL Flip 3-6 to anything that has a length of 1.5", 1.75" or 2" tubing
- Can also be used as a universal mount for anything you need to hang in your race car, off-road vehicle, etc
- Completely reversible, and can be moved from vehicle to vehicle
-
VTT Billet Velocity Stack (V-Stack)
3" • 4" • 5" Inlet Sizes
Running an open turbo and want to straighten airflow into the compressor for maximum efficiency? The VTT Billet Velocity Stack is exactly what you need.
Backed by fluid-dynamics principles, a proper bellmouth / velocity stack smooths incoming airflow, reduces turbulence, and improves air entry into the turbocharger—or intake on naturally aspirated applications. Unlike thin, stamped alternatives, our V-Stacks are precision-machined for strength, consistency, and performance.
Each unit is CNC-machined from 6061-T6 billet aluminum and anodized for durability and corrosion resistance. Available in 3", 4", and 5" inlet sizes, these stacks are designed to fit any intake tubing or turbocharger inlet of the corresponding diameter.
-
Give the Gift of VTT! Looking to get your friends, or family some go-fast parts, and no idea what they need, only that they love VTT? Well, our Gift Cards have you covered! They come in $50, $100, $250, $500, and $1000 increments. Each gift card is precision cut out of plastic in the shape of the VTT logo and has the dollar amount and the code on the back. Each gift code is unique and is locked to that card. To redeem simply enter the code during check out it will remove that amount, and if you have any leftover it will go back to the card.
You can choose to have your card physically mailed to you, or a virtual card where we can send you a scan of your card.
-
Please Note: This is a Virtual Gift Card. After purchase you will receive an email with your Gift Card code
- Looking to protect your single turbo investment, dont have a ton of room, and need a low profile filter that can flow what you need? VTT Has you covered with our Low Profile Single turbo Air Filters. These filters are custom-made for VTT. They are made with a heat-resistant silicone base, and a high-flowing cotton weave element with a pre-oiled design to catch contaminates but allow free flow. We currently offer them in Black, and 3 flange sizes. 3", 4" and 5" flange. With two filter heights. Tested at over 1200WHP with no loss of power observed. Filter Options - Offered in White, and Black with the following dimensions Short - 3.75" Tall, 7.5" OD Large end, 5" Small end 3", 4", or 5" Flange Tall - 4.5" Tall, 7.5" OD Large end, 5" Small end 3", 4", or 5" Flange
-
Introducing the VTT OBD-LOCK – Enhanced Security & Improved Design!
We are excited to announce our OBD-LOCK! This latest version has been completely redesigned for improved strength, ease of installation, and enhanced protection. Key upgrades include:
No more OBD port penetration – eliminates any risk of damage
Revised thread style – prevents stripping for a secure fit
Stronger, more durable design – ensures maximum securityUltimate OBD Port Protection
The VTT OBD-LOCK is precision-machined from billet 6061-T6 aluminum and is engineered to completely lock out your OBD port, preventing unauthorized access.
Anti-Theft Protection – Prevents thieves from accessing the OBD port to duplicate keys or disable security systems
Dealer/Tech Lockout – Stops unauthorized tune changes or system modifications
Tamper-Proof Design – Cannot be removed without physically destroying the OBD port unless the correct tool is usedVTT OBD-LOCK – Version 2 NON-GM
Universal Fit for All Non-GM (General Motors) VehiclesThis device is compatible with all non-GM vehicles, including but not limited to:
-
All VAG group vehicles (VW, Audi, Bentley, etc.) — including recessed port VW/Audi models
-
Ford, Nissan, Honda, Toyota, Porsche, Dodge, Ram, Jeep, Kia, Subaru, and more
Not compatible with GM (General Motors) vehicles.
VTT OBD-LOCK – Version 2 GM
Universal Fit for GM (General Motors) Vehicles ONLYThis version is specifically designed for General Motors vehicles, including GM, Chevrolet, Cadillac, Holden, and other GM-branded models.
If your vehicle is anything other than a General Motors product, you will need the Non-GM version.
-
- Unsure of the state of your CHRA's, whether brand new from a questionable source or rebuilt? Don't install them without having a proper High-Speed balance done! This is the #1 most critical factor when building a turbocharger, and is even more important for performance turbochargers or small twins that see a LOT of RPM. We use a Turbo Technics VS3 balancer, and balance most units down to under .5G Not all turbos will be able to pass a high-speed balancing test for any number of reasons (usually poor assembly, bent shaft, etc), if they will not pass, we will send you the specs they are in, and as close as we could get them. We then will give you the option to send them back, or we can disassemble, and rebuild them in-house using our other balancing, and assembly tools to ensure a properly built/balanced unit. The service is for most turbos, and we have the capability to balance most units, NOT ALL. If sending in twins please choose TWO as the quantity
UNITS MUST BE SENT IN WITH NO HOUSINGS, AND IN A CONDITION READY TO BE BALANCED, IF YOU NEED TO SEND IN COMPLETE TURBOS, WE CAN DISASSEMBLE, AND BALANCE FOR YOU, BUT AN EXTRA CHARGE WILL APPLY. IF THE UNITS ARE SENT IN A CONDITION WHERE THEY CAN NOT BE BALANCED WE WILL LET YOU KNOW THE PRICE TO GET THEM TO A STATE WHERE THEY CAN BE
- Out of stockThe upgrade comes with our own custom rod end to fit the EBM, and is 100% ready to install.
- VTT silicone inlets are the premiere choice for your EBM inlet needs. Made from high quality, wire impregnated silicone, these inlets are a full 6mm thick, and can withstand even the harshest underhood conditions.
- VTT silicone Charge Pipes are the premiere choice for your EBM Charge Pipe needs. Made from high quality, wire impregnated silicone, these inlets are a full 6mm thick, and can withstand even the harshest underhood conditions.
- A plug and play BOV option for your Ecoboost Mustang. This kit comes with everything you will need to replace your undersized factory DV with a high quality Turbosmart Race port.
-
VTT -16 Billet HIGH-FLOW Catch Can System
Maximum Venting for Maximum Power
VTT is proud to introduce our -16 Billet High-Flow Catch Can System — designed from the ground up for high-horsepower applications requiring serious crankcase ventilation. Whether you're pushing over 900WHP or beyond 2000WHP, this system delivers unmatched performance, reliability, and engine bay cleanliness.
Key Features:
-
Supports -16 AN lines (with optional -12 or -20 fittings)
- 20 Fluid OZ capacity
-
Engineered for big-power builds needing high crankcase pressure relief
-
Triple-stage filtration system to eliminate oil mist — even in the event of engine failure
-
Designed, tested, and proven to keep oil inside the catch can — not in your engine bay
Triple Filtration Technology:
-
Stage 1 - Stainless steel filter – captures 95% of oil mist on entry
-
Stage 2 - Perforated diffuser plate – further disperses and slows down airflow
-
Stage 3 - Final stainless mesh layer – scrubs out any remaining vapor before venting
This advanced system has been tested with over 200 PSI of pressure and more than half a quart of oil without releasing a trace of oil mist. As long as the catch can is properly serviced and not overfilled, even catastrophic engine failure won’t result in a mess under your hood.
Application-Specific Kits Available:
We offer plug-and-play kits for popular platforms, including:
-
G8X M2/M3/M4 (S58) SINGLE TURBO ONLY
-
F9X X3M/X4M SINGLE SINGLE TURBO ONLY
-
A9X Toyota Supra
Each Plug and play kit includes everything needed for installation: catch can, vehicle-specific bracket, fittings, hoses, and optional drain. Again, plug-and-play kits include ALL required parts. Bracket, fittings, line, etc. No additional fittings are required except the drain if wanted.
-
- Out of stockThe VTT Single Shot EBM pump is a must have when running E85, and looking for anything over 350WHP
- VTT is proud to offer our EWG "Direct Control System" or DCS! This is a completely new innovation for people looking to control the highest-flowing wastegate on the market using an existing BMW electronic actuator. This system will allow BMW owners who have a vehicle with Electronic Wastegates from the factory to utilize this system to control an externally wastegated turbo system, AND it will ALSO allow ANY vehicle to use this setup to control your own custom turbo system. This is done by utilizing our custom 7075 Billet aluminum bracket coupled with a Turbosmart Straight gate, and if needed an EWG controller made for us by DCCD Pro. This allows direct external wastegate control over any turbocharger system with or without EWG for the factory. Features:
- Utilizes the most current wastegate technology the Turbosmart Straight Gate. This gate allows maximum flow with minimal restriction, low drive pressure, and much more. Full details can be found here - https://www.turbosmart.com/product/electronic-straightgate-esg50-external-wastegate/
- Can be configured in multiple ways, and angles based on how you mount the adapter
- The adapter is 7075 Aluminum which has the strength of steel and weight of aluminum
- All connection fittings, are made from Nitronic 60 which has extremely high temperature and wear properties
- Zero Drive Pressure, no springs, no poppet valves, direct control over the gate using factory ECU logic
- Adaptable to ANY turbo system on any car to provide the ultimate in boost control!
- Out of stockWHP Level supported (with proper fuel, upgrades, and tuning) Stock-500WHP Stage 2 / Stock -550WHP Stage 2+
- Out of stockWHP Level supported (with proper fuel, upgrades, and tuning) Stock-500WHP Stage 2 / Stock -550WHP Stage 2+
- Sale!
VTT x PFS EBS (External Brushless System) Fuel System
VTT, in collaboration with Performance Fueling Solutions (PFS), is proud to introduce the PFS EBS — External Brushless System.
The EBS is a fully stand-alone, next-generation brushless fuel system available in both platform-specific and universal fitments. Built around state-of-the-art Protec brushless pump technology, this system is capable of supporting up to 2,500 HP on ethanol-based fuels — and even more on gasoline or ethanol blends.
With its compact 15" x 10" footprint and ultra-lightweight construction, the PFS EBS is engineered for performance without compromise. The complete system — including pumps, surge tank, FPR, controllers, and wiring harness — weighs in at under 10 lbs (dry), thanks to a carbon fiber mounting plate and carefully chosen lightweight materials.
EBS Bench Testing Video:
EBS Bench Test Video - VTT is proud to offer PTE Turbocharger products! Please Note: All Precision Turbos have a 2-3 week shipping time
