-
Sale!
VTT x PFS EBS (External Brushless System) Fuel System
VTT, in collaboration with Performance Fueling Solutions (PFS), is proud to introduce the PFS EBS — External Brushless System.
The EBS is a fully stand-alone, next-generation brushless fuel system available in both platform-specific and universal fitments. Built around state-of-the-art Protec brushless pump technology, this system is capable of supporting up to 2,500 HP on ethanol-based fuels — and even more on gasoline or ethanol blends.
With its compact 15" x 10" footprint and ultra-lightweight construction, the PFS EBS is engineered for performance without compromise. The complete system — including pumps, surge tank, FPR, controllers, and wiring harness — weighs in at under 10 lbs (dry), thanks to a carbon fiber mounting plate and carefully chosen lightweight materials.
EBS Bench Testing Video:
EBS Bench Test Video -
Sale!
Stop the Flex. Launch with Confidence.
Soft bushings are the enemy of hard launches and drivetrain longevity. The factory BMW transfer case bushings on the F9X M5/M8 platform are notoriously soft—exactly the opposite of what you want when you're putting serious power to the ground.
Sure, you could replace the entire bushing with a solid one, but that often requires lowering or removing the transfer case—not to mention the added NVH (noise, vibration, and harshness) that comes with it.
Our VTT transfer case bushing inserts offer a smarter solution: reduce bushing flex without sacrificing comfort. You keep smooth, quiet drivability around town and at idle—but when it’s time to launch, the transfer case stays planted.
-
Sale!
VTT B58/S58 HPFP Block-Off Plate Kit
If you’re converting your B58 or S58 build to port injection (PI) only and removing the direct injection (DI) system and high-pressure fuel pumps (HPFPs), you’ll need to properly seal the HPFP ports in the valve cover.
Our billet aluminum block-off plates provide a simple, clean solution.
Just remove the HPFP and cam follower, then install the plate — it seals the valve cover and eliminates the HPFP cleanly and securely.Please Note:
-
Removing the HPFP typically requires a standalone ECU.
-
If you’re only removing a single HPFP (such as on the S58), a tune adjustment will be necessary for proper operation.
-
-
Sale!
VTT B58 (TU) HMM Delete Plate
Looking to build a race car with a B58 engine?
Doing a B58 swap and don’t want the complicated BMW Heat Management Module (HMM)?
Need a simple -16AN or -20AN line setup instead of the factory tangle?If so, the VTT B58 (TU) HMM Delete Plate is exactly what you need.
This kit eliminates the bulky OEM Heat Management Module and replaces it with a clean billet block-off solution. The included rear water pump plug and hold-down bracket ensure proper sealing, while the modular -16ORB port allows you to run your choice of -16AN, -20AN, or any compatible fitting. Build your lines, run them to the radiator, add an inline thermostat if desired — and enjoy a vastly simplified, race-ready B58 cooling system.
-
PFS Stage Cheap DIY Fuel Pump Upgrade Kit (plus limited Pre-Built units available)
Need more fueling headroom but don’t want to drop big money on a full upgrade? The Stage Cheap DIY kit is exactly what it sounds like — an affordable, effective way to boost your low-pressure fuel pump performance without adding wiring, controllers, or complexity.
This kit repurposes high-quality OEM-based components into a high-flow solution for the A90/A91 Toyota Supra and BMW G-Series platforms (excluding M3/M4 and X3M/X4M).
Key Features:
-
✅ ~50% more flow than a stock LPFP
-
✅ Once assembled, kit is 100% plug-and-play
-
✅ No additional wiring or external controllers required
-
✅ Retains full factory fit and function
-
✅ Ideal for pump gas or E85 builds
-
✅ Built from OEM-quality components
-
✅ A perfect entry-level fueling upgrade
-
-
Introducing the VTT Remote Oil Cooler Plate for BMW B58 Engines Need extra oil cooling for your track-oriented B58 build or simply looking for better cooling capacity in high-temperature climates? If so, you’re likely considering running an external or upgraded oil cooler on your BMW B58-powered vehicle. However, BMW’s design doesn’t make this easy—the heat exchanger is built directly into the oil filter housing. That’s where the VTT Remote Oil Cooler Plate comes in. This innovative solution allows you to easily and conveniently remove the factory coolant-supplied heat exchanger on the oil filter housing and replace it with -10AN or -8AN fittings, simplifying the process of running your oil cooler lines. No need to worry about looping the coolant—our plate features a built-in housing that seamlessly loops the coolant circuit for a hassle-free installation.
Key Features:
- Convenient Oil Cooler Integration: Add a remote oil cooler to your BMW-powered vehicle (Gen 1 and Gen 2 B58 engines).
- Flexible Plumbing Options: Includes -8AN or -10AN fittings for easy line routing.
- Built-In Coolant Loop: Eliminates the need to manually loop the coolant circuit, simplifying installation.
- Direct Plug-and-Play Replacement: No modifications or retrofitting required.
- Optional Fittings Available: Choose with or without fittings based on your setup.
What’s Included:
- One Block-Off Plate with Coolant Loop Housing
- Six M6 Bolts
- Optional -10AN or -8AN Fittings
- Optional Factory Gaskets
-
High-Boost Crankcase Ventilation Adapter for BMW Engines Building or running a high-boost, high-powered BMW engine? Boost increases crankcase pressure, which, if left unchecked, can lead to issues such as smoking, power loss, and even engine failure. Adequate venting is essential for optimal performance and engine health. These are designed to connect directly to S58/B58(TU) stock VC, or screw into ANY VTT Billet or Cast VC While some believe a -10AN vent is sufficient for these builds, the truth is: it’s not. To address this, we developed a larger, more effective solution for our builds—now available for everyone. Our Oil Cap adapter securely snaps in place, replacing your oil cap and providing a platform for a -16ORB fitting in a variety of configurations. Choose from -12AN to -20AN fittings, depending on your build’s needs. This cap is thicker than our low-profile option so care must be taken when planning hood clearance for the versatile venting options.
Key Features:
- Attractive Oil cap design
- Connects to stock S58/B58(TU) VC or VTT Billet/Cast VC
- Vented, comes with multi-hole venting to knock down large oil droplets before they make their way into the catch can system
- High-performance venting: Supports configurations from -12AN to -20AN fittings.
- Customizable: Compatible with various fittings to suit your build.
Important Notes:
- This kit requires you to supply your own hose, hose ends, and catch can to complete the system.
- Some fitting options may require 4–5 days for shipping, as we keep only select configurations in stock.
- Also fits other platforms such as B48, B46, Mini, etc. DOES NOT FIT Gen 1 B58
-
High-Boost Crankcase Ventilation Adapter for S58/B58 Engines Building or running a high-boost, high-powered S58 or B58 engine? Boost increases crankcase pressure, which, if left unchecked, can lead to issues such as smoking, power loss, and even engine failure. Adequate venting is essential for optimal performance and engine health. While some believe a -10AN vent is sufficient for these builds, the truth is: it’s not. To address this, we developed a larger, more effective solution for our builds—now available for everyone. Our low-profile adapter securely snaps in place, replacing your oil cap and providing a platform for a -16ORB fitting in a variety of configurations. Choose from -12AN to -20AN fittings, depending on your build’s needs. At just 10mm thick, this adapter maximizes hood clearance for versatile venting options.
Key Features:
- Low-profile design: Only 10mm thick for maximum hood clearance.
- High-performance venting: Supports configurations from -12AN to -20AN fittings.
- Customizable: Compatible with various fittings to suit your build.
Important Notes:
- This kit requires you to supply your own hose, hose ends, and catch can to complete the system.
- Some fitting options may require 4–5 days for shipping, as we keep only select configurations in stock.
- Also fits other platforms such as B48, B46, Mini, etc. DOES NOT FIT Gen 1 B58
-
VTT-FAB B58 Factory Control EWG Top Mount Single Turbo kit
For BMW G-Series & Toyota A91 6-Port B58 Platforms
VTT-FAB is proud to offer the premiere top-mount single turbo system for the BMW G-Series and Toyota A91 B58 platforms. This kit is 100% made in the USA at our Hayward, CA facility, using only the highest-quality materials and components.
At the core is a hand-fabricated equal-length 321 stainless steel manifold with billet flanges, designed for maximum flow, durability, and that signature 6-into-1 turbo sound. The system is paired with our factory-controlled external wastegate setup, featuring a Turbosmart 60mm Straight Gate. This innovative design allows full external gate control through the OEM ECU — no additional boxes, MAC solenoids, or vacuum/boost lines required. Simply reuse your factory actuator with our adapter for seamless, plug-and-play control from 0 PSI all the way up to your turbo’s limits.
Unlike other kits, the VTT-FAB system uses no silicone couplers. Instead, we provide VTT-FAB HD clamps to eliminate the risk of blown boost hoses under extreme load.
⚠️ Important Notes:
-
Every VTT-FAB kit is built to order and cannot be canceled once fabrication begins. Please order carefully.
-
If your kit of choice is listed out of stock, email [email protected] for current build times.
-
Garrett turbo options are oil-cooled only (no water lines). This is perfectly fine for street and drag applications. For extended track/road-race use, we recommend adding water cooling
-
-
VTT is proud to offer our Pre-Preg Hand Crafted Carbon Fiber engine covers for the S58 engine. These are plug-and-play and snap into the factory mounting studs using the factory rubber mounts. BMW did a fabulous job on the latest engine offerings, but the overuse of plastics leaves the engine bays looking cheap, and unfinished. These carbon fiber engine covers, as well as our carbon fiber strut bars, are the perfect addition for anyone looking to give their engine bay, a polished, and sharp look. Available in Gloss, and Matte finish for the G8X and X3/4M platforms
PLEASE NOTE: MUST REUSE FACTORY EMBLEM
-
Low Profile socket for installing, and removing the vanon central valve bolt on BMW/Mini/Rolls Royce, and some For vehicles. This tool give you the space to get a TQ wrench in between the engine and the firewall to properly tighten the vanos central valve bolt.
- Removes later style central valve on BMW Vanos Hubs and Ford VCT
- Services BMW B38, B48, B58, MINI Vanos, and Ford VCT modules
- 22mm x 16 Points
- 1/2" Square Drive
- Chrome molybdenum with black phosphate finish. Compare to Ford Factory Tool 303-1661-3 and BMW Factory Tool 2-450-487
-
Looking to up your boost limit on just about any BMW vehicle that runs a 3 or 4-wire BMW map sensor including but not limited to S58, B58, N54, N55, S55, S63, B48, B47, B42, B57, B46? We were too, so we decided to make a very easy plug-and-play kit for 3, and 4-wire BMW map sensors. These kits will allow you to completely replace the 3-wire sensor with one of our sensors, leave your stock 4-wire in place for IAT sensing, and move the power, ground, and sensor signal from the factory sensor to our sensor. These sensors have the proper scaling which will allow your tuner to simply change your map sensor scaling in the tune, and the factory ECU will be able to utilize the sensor voltage with no problem. We are offering these in 5 bar (58 psi), and 6 bar (72 psi), and each comes with a plug-and-play harness, and optional fittings for ease of installation.
Note: For the S58/B58 our Factory style Pre-Throttle map sensor is also 5 bar, and will work fine coupled with the post throttle kit, but the scaling is different, if you want matching Voltages Pre/Post throttle you can run two of these.
A variety of install pics can be found below and - Here
Scaling PDF Links: 5-Bar / 6-Bar
Features include:- Plug and Play harnesses with no wire splicing
- Output wire for connecting a PI or external controller to your post-throttle map sensor for the most stable signal that is not affected by throttle closure
- Different fittings are available for your plumbing needs.
- Can have matching voltage signals for pre/post throttle for ease of tuning, and boost reference
- B58/S58 etc Pre Throttle - 3 Wire Harness (Charge pipe to 1/8" NPT adapter needed, for B58/S58 90 degree adapter needed to provide sensor clearance)
- B58/S58 Post Throttle - 4 Wire Harness (Boost reference will be needed from manifold to sensor)
- F90 M5 Pre/Post Throttle - 4 Wire Harness (May need to repin) (Boost reference will be needed from manifold to sensor)
- Most all other platforms Pre/Post Throttle - 4 Wire Harness (May need to repin) (Boost reference will be needed from manifold to sensor)
- B58
- S58
- S63/ S63TU
- N63
- N54
- S55
- N55
- N20
- B46
- B48
- B57
- B47
-
VTT is happy to carry GSC Power Division Gen 2 B58 Camshafts! GSC Power-Division billet cams for the BMW B58B30C Double Vanos, Valvetronic (variable lift) power plant of the 2018-2024 MKV Toyota Supra and 2018-2024 BMW B58 G-body vehicles. GSC Stage 1, 2, and 3 Camshafts for BMW Gen 2 B58 are the quintessential camshaft for the platform and will provide the greatest power gains for your B58 build! Couple your camshafts with GSC Beehive Springs, and retainers, and if building the head we recommend GSC intake/exhaust valves, guides, and stem seals.
Full Cam specs can be found below
PLEASE NOTE: WITH STAGE 2 AND STAGE 3 CAMS UPGRADED VALVE SPRINGS ARE REQUIRED!
-
Looking to fix the diff bolt issue on your G0X X3/X4, G3X 5 Series, and G1X 7 Series chassis? VTT is proud to offer our Rear diff bushing insert kit. This is pressed into the factory bushing and fills the voids in the bushing. This keeps the stock bushing ride compliance but removes any unwanted movement. These are sold as a kit and are available in the rear side only. Kit includes:
- One Billet Bushing insert
- Two 46mm Hardened Steel Washers
- One 12.9 M14 Bolt
- One M14 Lock nut
All products that are designed to stiffen or reduce drivetrain movement inherently have the tendency to increase NVH or Noise, Harness, or vibration. While these bushings inserts have been found to add little NVH in most instances. Your results and sensitivity to NVH may vary. This product is designed to reduce drivetrain movement, and that was the goal when designing and manufacturing this product. Returns for NVH are not accepted once products are installed.
-
Looking for a head gasket for your BMW that will hold ALL of the boost? So were we, and nothing we tried worked. So we took matters into our own hands and had what we wanted made. These gaskets are made out of carbon material, and use stainless steel fire rings to ensure you are not pushing boost into your water jacket or between cylinders. There are two versions:
- One does NOT require a groove to be cut into the block
- One DOES require a groove to be machined into the block to accept the fire ring.
- Custom made to our specs from Carbon material that will form your head/deck, and seal oil/water passages while fire rings, keep boost in the combustion chamber
- FULLY tested in-house on multiple builds to ensure boost level can be achieved
- They are NOT like the other fire ring gaskets on the marker (SCE/Athena) that do not require machine work, we had zero luck with those. THESE FLAT OUT WORK!
- Choose non-machined or machined version
- Different thicknesses are available as a custom order (4-8 week lead time)
- Different Bores Available as a custom order (4-8 week lead time)
For any gaskets NOT in stock expect a 4-8 week lead time as these are custom-made for us. This includes ANY gasket we currently do not have in stock.
-
BMW damper bolts are grade 10, and Torque to Yield, meaning one-time use. This is fine for factory power levels, but when turning things up. These bolts leave a lot to be desired. We have seen damper bolts come loose, and break causing engine and crank damage, we have seen improper TQ load between bolts. The factory bolts are just not up to snuff if you plan to run above factory power levels. We are proud to offer a solution with genuine ARP 8740 Chromoly replacements at a budget-friendly price. These bolts are made in the USA to ARP's exacting standards meaning you know each bolt is going to do what it was designed to do, and that is provided even, repeatable TQ load. Each kit contains:
- 4 VTT/ARP 4340 Chromoly Damper Bolts
- Thread Size: M10 x 1.5
- Fastener Head Style: 12-point
- Fastener Material: Chromoly
- Fastener Color: Black
- Fastener Grade: ARP 8740 chrome moly
- Fastener Tensile Strength (psi): 180,000+ psi
- Wrench Diameter: 12mm
-
Looking for a way to do burnouts in your ATC13-2 Equipped Xdrive BMW that doesn't have an RWD mode such as G-Series non-M vehicles, and SUVs? We were too! VTT is proud to offer the ONLY easy-to-install, plug, and-play Xdriove controller on the market. This device will allow you to turn off, and turn on again your X-drive capability from the driver seat with a remote. While other options do exist such as X-Delete, or an in-dash gauge, one is a very slow process and is not viable to use as a way to do a burnout at the drag strip, and the other is a very expensive, AND very intrusive device that requires removal of most of the dash, and installing a gauge. Our solution takes 30 seconds to install once you gain access to the underside of the vehicle, and can be removed just as easily. Once installed, you can remotely disable your Xdrive from the driver's seat to perform your burnout, and then quickly enable it again to perform your launch with AWD active. This action does NOT require a key cycle, as soon as you activate it again the car will dismiss any lights and codes generated. This truly is the best of both worlds for ease of use, practicality, and effectiveness, all while coming at a very affordable price. This device uses a BMW plug on one end, and our custom-printed male plug on the other, for a plug, and play OEM fit. NO cutting any wires!
PLEASE NOTE: WHEN ACTIVATED YOUR DASH WILL LIGHT UP WITH CODES BECAUSE YOU ARE IN ESSENCE DISCONNECTING THE TRANSFER CASE. YOU MAY ALSO EXPERIENCE SPORT STEERING DURING THIS TIME WHICH MEANS A HARDER-TO-TURN WHEEL. THIS IS ALL NORMAL. WE ONLY SUGGEST USING THE DEVICE FOR SHORT PERIODS OF TIME, SUCH A BURNOUT AT THE STAGING AREA OF A DRAG RACE. IN SOME INSTANCES, THE CAR WILL NOT ALLOW A BURNOUT IF THE BRAKE, AND THROTTLE ARE APPLIED AT THE SAME TIME DUE TO ECU LOGIC, IN THESE INSTANCES INSTALLING OUR WIRELESS LINE LOCK ELIMINATES THIS ISSUE. MANY TIMES AN AFTERMARKET TUNE WILL ALSO ELIMINATE THIS ISSUE.
THIS DEVICE CAN BE USED FOR THINGS SUCH AS DRIFTING DONUTS ETC., BUT WE DO NOT CONDONE ANY DRIVING OUTSIDE OF LEGAL GUIDELINES. PLEASE USE THIS PRODUCT RESPONSIBLY. SEE ABOVE FOR WHAT IS GOING TO HAPPEN WHEN YOU ENGAGE THIS DEVICE
THIS DOES NOT FIT F-SERIES VEHICLES
Install/User Guide is here - Install Guide
Features:- Works on any vehicle outlined below from stock to tuned
- 30-second install
- 30-second removal
- NON-intrusive ZERO cutting of wires, or taking anything apart on the vehicle TRULY plug and play
- OEM fit and finish on the plugs
-
PFS is proud to offer a true drop-in LPFP for S55-powered BMWs. This LPFP needs NO additional pumps, wiring harnesses, controllers, etc. Capability is 850whp on E85 and up to 1000whp on race fuel. We start with a factory bucket, we modify it to accept our high-flow brushless fuel pump. We then re-terminate the factory wiring to accept the new pump. No wiring splices, done the same way the factory does -the right way. Every pump is fully tested on our flow bench to ensure proper function before shipping -you're going to be installing a product that has already proven itself. This pump is a true drop-in meaning you pull the factory unit out, install this pump, plug the factory plug into the hat, and you are done. The stock ECU controls the pump fully, and NO tune changes are required to take advantage of it. Installation is easy for the DIY'er, and if you use a performance shop it'll be easy for them -just tell them to remove the old and replace it with new same as factory pump.
-
VTT is proud to offer our EWG "Direct Control System" or DCS! This is a completely new innovation for people looking to control the highest-flowing wastegate on the market using an existing BMW electronic actuator. This system will allow BMW owners who have a vehicle with Electronic Wastegates from the factory to utilize this system to control an externally wastegated turbo system, AND it will ALSO allow ANY vehicle to use this setup to control your own custom turbo system. This is done by utilizing our custom 7075 Billet aluminum bracket coupled with a Turbosmart Straight gate, and if needed an EWG controller made for us by DCCD Pro. This allows direct external wastegate control over any turbocharger system with or without EWG for the factory. Features:
- Utilizes the most current wastegate technology the Turbosmart Straight Gate. This gate allows maximum flow with minimal restriction, low drive pressure, and much more. Full details can be found here - https://www.turbosmart.com/product/electronic-straightgate-esg50-external-wastegate/
- Can be configured in multiple ways, and angles based on how you mount the adapter
- The adapter is 7075 Aluminum which has the strength of steel and weight of aluminum
- All connection fittings, are made from Nitronic 60 which has extremely high temperature and wear properties
- Zero Drive Pressure, no springs, no poppet valves, direct control over the gate using factory ECU logic
- Adaptable to ANY turbo system on any car to provide the ultimate in boost control!
-
Looking to protect your single turbo investment, dont have a ton of room, and need a low profile filter that can flow what you need? VTT Has you covered with our Low Profile Single turbo Air Filters. These filters are custom-made for VTT. They are made with a heat-resistant silicone base, and a high-flowing cotton weave element with a pre-oiled design to catch contaminates but allow free flow. We currently offer them in Black, and 3 flange sizes. 3", 4" and 5" flange. With two filter heights. Tested at over 1200WHP with no loss of power observed. Filter Options - Offered in White, and Black with the following dimensions Short - 3.75" Tall, 7.5" OD Large end, 5" Small end 3", 4", or 5" Flange Tall - 4.5" Tall, 7.5" OD Large end, 5" Small end 3", 4", or 5" Flange
-
Introducing the VTT OBD-LOCK – Enhanced Security & Improved Design!
We are excited to announce our OBD-LOCK! This latest version has been completely redesigned for improved strength, ease of installation, and enhanced protection. Key upgrades include:
No more OBD port penetration – eliminates any risk of damage
Revised thread style – prevents stripping for a secure fit
Stronger, more durable design – ensures maximum securityUltimate OBD Port Protection
The VTT OBD-LOCK is precision-machined from billet 6061-T6 aluminum and is engineered to completely lock out your OBD port, preventing unauthorized access.
Anti-Theft Protection – Prevents thieves from accessing the OBD port to duplicate keys or disable security systems
Dealer/Tech Lockout – Stops unauthorized tune changes or system modifications
Tamper-Proof Design – Cannot be removed without physically destroying the OBD port unless the correct tool is usedVTT OBD-LOCK – Version 2 NON-GM
Universal Fit for All Non-GM (General Motors) VehiclesThis device is compatible with all non-GM vehicles, including but not limited to:
-
All VAG group vehicles (VW, Audi, Bentley, etc.) — including recessed port VW/Audi models
-
Ford, Nissan, Honda, Toyota, Porsche, Dodge, Ram, Jeep, Kia, Subaru, and more
Not compatible with GM (General Motors) vehicles.
VTT OBD-LOCK – Version 2 GM
Universal Fit for GM (General Motors) Vehicles ONLYThis version is specifically designed for General Motors vehicles, including GM, Chevrolet, Cadillac, Holden, and other GM-branded models.
If your vehicle is anything other than a General Motors product, you will need the Non-GM version.
-
-
VTT Universal Turbo Fittings – Oil & Coolant Solutions for BMW Turbo Builds!
Looking to fabricate your own turbo kit for BMW platforms? Need an easy solution to block off water lines or create custom feed and drain fittings? Look no further! VTT offers a wide range of high-quality oil and coolant fittings to simplify your build. Our fittings are designed for most late-model BMW platforms, providing a plug-and-play solution for custom turbo setups. 📌 Available Fitting Options: 🔹 Oil Feed – -4 AN Male 🔹 Oil Drain – -10 AN Male 🔹 Coolant Fittings – Barbed Male or Block-Off Options -
Stop the Flex. Launch with Confidence.
Soft bushings are the enemy of hard launches and drivetrain longevity. The factory BMW transfer case bushings—especially on the G8X and F9X platforms—are notoriously soft. That’s the last thing you want when you’re putting serious power down.
Sure, you could replace the entire bushing with a solid one, but that often requires lowering or removing the transfer case—not to mention the added NVH (noise, vibration, and harshness) that comes with it.
Our transfer case bushing inserts offer a smarter solution: reduce bushing flex without sacrificing comfort. You keep smooth, quiet drivability around town and at idle—but when it’s time to launch, the transfer case stays planted.
Fitment Notice – Two Versions Available:
BMW uses two different transfer case bushing types. We now offer Version A and Version B inserts to match.
⚠️ You must physically inspect your vehicle’s bushing to determine which version you need.
We are not responsible for incorrect orders if this step is skipped. -
VTT is proud to offer a truly plug-and-play line lock kit for select BMW vehicles that does NOT require running wiring inside the car, mounted switches, holes in the dash, etc. Our newly designed and released line lock kits use a 40amp wireless remote control switch with 4 different modes that allow you to tailor your line lock setup exactly as you prefer. You simply install the solenoids, install the harness with the switch which has all the wiring terminated, bleed the brakes, and you are ready for effortless burnouts which will not be interfered with by the DME because you are holding the brakes, nor wear your rear brake pads. You can store the remote anywhere in your vehicle, center console, cup holder, door cup holder, etc., and when you need to do a burnout to heat your race tires it's in arm's reach without running any wiring into the vehicle. Fitment is confirmed for G8X M3/4, A9X Supra - The kit itself including lines, solenoids, etc will fit most all late model BMW Chassis including F8X, F3X, G2X, etc. The main concern will be mounting the wireless switch in the passenger cowl area. The kit includes:
- Line lock solenoids with weather pack connectors
- Two Parker 90-degree -3 an fittings
- Two Stainless Steel adapter fittings
- Two DOT Approved Stainless Steel brake lines
- One complete wiring harness
- One Remote control switch with TWO remotes
-
VTT Carbon Fiber Driveshaft for BMW Applications
Why overpay for a carbon fiber BMW driveshaft?
VTT is proud to offer a premium carbon fiber driveshaft manufactured exclusively for VTT in the USA by GCDS (Gulf Coast Driveshaft) — one of the premier driveshaft manufacturers in the country with extensive experience in high-performance and drag racing applications.
Each driveshaft is constructed using 3.31" carbon fiber tubing, paired with NEAPCO Performance 1350 series U-joints, then bonded using a proprietary high-strength process and precision balanced to within 1/8 in-oz as a complete assembly.
Every shaft is torque tested in-house prior to shipping to ensure proper bonding and structural integrity. GCDS and VTT are among the few manufacturers that perform full torque testing on each shaft before it leaves the facility.
To complete the system, the driveshaft is paired with VTT-designed 7075 aluminum adapters, eliminating the factory guibos and unnecessary flex points. The shaft connects directly to the BMW 3-bolt front flange, while a VTT 4340 rear adapter replaces the factory slip-in / screw-retained shaft design for improved strength and reliability.
Proudly Made in the USA.
PLEASE NOTE! YOU MUST SEND US YOUR VIN NUMBER TO PROPERLY PROCESS YOUR ORDER, IF YOU DO NOT SEND YOUR VIN, YOU ORDER IS GOING TO BE HELD
PLEASE NOTE! Driveshafts can have UNUSUALLY LONG LEAD TIMES. We hope to reduce this with GCDS, but if the shaft shows OUT OF STOCK, expect a lead time of 4–8 weeks, unless we specifically state that it can ship sooner.
Due to the nature of these shafts being manufactured by a 3rd party, ANY ORDERS PLACED FOR VTT CF DRIVESHAFTS ARE 100% FINAL.
NO REFUNDS. NO CANCELLATIONS. FOR ANY REASON.
THIS INCLUDES LONG LEAD TIMES.
PLEASE ORDER CAREFULLY. ONCE THE ORDER IS PLACED, IT IS FINAL.
-
Tired of your Dragy flying all over the car as you try to do runs? Tired of low sats or no sats warning due to improper location of the Dragy in the vehicle? Well say goodbye to those issues with our new Carbon Fiber and Plastic Dragy holders. These are made from either 100% Pre-Preg Carbon Fiber, or molded plastic for a perfect fit. The carbon fiber gives it just the right look to add to your performance vehicle! Each holder has dual Suction cups and will stick to any smooth surface. We suggest mounting them in the upper left or right corner of your windshield with a full view of the sky. Dragy holder features
- Stop your Dragy from flying off the dash, and having to search for it
- Position your Dragy in the optimal position for the best satellite coverage
- VTT Dragy holder exposes the entire top of the Dragy so nothing is blocking the receiver from the Satellite
- The charging port is not blocked and can be accessed with the cover on
- Choose from REAL Carbon Fiber or Molded Plastic
-
The Factory B58 TU Upper Cylinder head hose is plastic and is right in the path of your charge pipe if you lose a connection and it blows off. If this does happen to you it can break the plastic neck emptying your coolant in seconds causing you in the best-case scenario to be stranded, and in the worst-case scenario expensive engine damage. Add some cheap insurance with our Billet Upper Cylinder head hose, this sits right above the plastic water neck. Product Details:
- Plug and play direct factory replacement
- 6061-T6 Billet aluminum with black anodizing for a corrosion-free life
- 7-Ply Silicone in 3 colors
- Cheap insurance against a blown charge pipe which could turn into a blown motor
-
Looking to make sure all metal contaminates that are possibly in your oil are not circulated? VTT has you covered with our Titanium Magnetic oil drain plugs for BMW, and any other vehicle that uses an M12x1.5 drain plug. This drain plug will capture any ferrous metal particles in your oil, and capture them to be cleaned during your next oil change. It also is stronger than a Steel or Aluminum drain plug, and looks cool! These are made from GR5 Titanium and use a rare earth magnet to capture metal particles in your oil... Kit includes:
- 1 Titanium Drain Plug
- 1 M12 Crush Washer
-
VTT is proud to offer a Phenolic spacer for the BMW B58 platform. When upgrading to an aluminum charge cooler you get the benefit of a better core, and more cooling capacity, but it also comes with the downside of DIRECT heat transfer from the head to the manifold which can cause heat soak and less-than-ideal IAT's even with an upgraded charge cooler. We manufacture these from G11 Expoxy sheet which has great heat and hardness characteristics, and we feel is the ideal material for this application. The thickness is 8mm.
Please note: Longer studs or bolts may be required introducing a phenolic spacer into your system
-
Improve engine/shifting feel without a huge increase in NVH or high cost! VTT G3X/G8X billet motor mount inserts upgrade mounts the way BMW does it, allowing a minimal increase in NVH while stiffening up the engine/shifting feel, and getting rid of excessive engine movement Fitment is below for GXX, G8X M2/3/4, F9X X3/4M using these mount part numbers and possibly others. They do NOT fit every engine option for these chassis. Please inquire first if you have questions 22 11 6 860 471 Engine mount, left G series Non-M 22 11 8 097 149 Engine mount, left G8X M2/3/4 22 11 6 860 457 Engine mount, left F9X X3/4M 22 11 6 860 472 Engine mount, Right G series Non-M 22119503432 Engine mount, right G8X M2/3/4 22116860458 Engine mount, right F9X X3/4M
-
VTT B58 “GC / GC-MID / GC+” Turbocharger Upgrades
Wheel Sizing / Power Support
Model Wheel Size (Comp/Turb) Stock Engine Power Range GC 54/55 Up to 600WHP GC-MID (TU ONLY) 54/60 Up to 650WHP GC+ 67/68 Up to 800WHP
Ready to take your B58 platform to the next level—without core charges, long waits, or compromising spool? VTT has you covered. Our 100% new casting B58 GC-Series turbochargers (GC, GC-MID, and GC+) retain the OE packaging advantages while removing the factory airflow limitations and weak internal architecture.
We start by keeping what BMW did right, then eliminate every bottleneck we found: the restrictive factory inlet, inefficient bearing housing oiling, small thrust assembly, and anything else holding the B58 back. Then we incorporate proprietary VTT improvements and cast everything at full OE-level quality.
The result? Serious B58 power made simple. GC turbos are direct bolt-on upgrades that retain all factory connections (oil, water, charge pipe, downpipe) while supporting 600WHP+ — with factory-like spool.
NOTE: The GC is Super Core ONLY, meaning no exhaust housing; this turbo plugs directly into your factory exhaust housing.
-
Sale!Looking for a Lightweight, AFFORDABLE drag pack that looks amazing for your BMW, Toyota, or VAG platform? Look no further! VTT is proud to announce our lineup of Drag pack wheels for various BMW/Toyota/VAG fitments! We teamed up with Rota and had them open custom molds for us of their extremely popular Grid design. With these molds, we have an exclusive on 15X10, 17X10, and 17X4.5 wheels in our exact specs. The wheels are currently offered in the colors and sizes below
A variety of Offsets are available, as well as spacers here - VTT Spacers can be found here - https://vargasturbo.com/product/vtt-billet-wheel-spacers/
As well as Center bore adapters here - https://vargasturbo.com/product/vtt-billet-hubcentric-wheel-bore-adapters/Wheels are priced EACH, meaning per wheel
PLEASE NOTE! CHECK FITMENT CAREFULLY. ANY WHEELS THAT HAVE HAD TIRES MOUNTED OR ARE DAMAGED DURING TEST FITTING ETC ARE NOT RETURNABLE!
We make NO CLAIM these fit ANY PLATFORM, or ANY factory brake set up. It is YOUR JOB to measure, and make sure they will fit BEFORE you mount tires or install them. WE NEVER suggest shaving down brake calipers to fit a smaller wheel. If they do not fit. GET A SMALL BRAKE KIT!
Colors offered:- Satin Black
- Gloss Black
- Bronze,
- Gun Metallic
- 15x10 ET45/ET40 (wheel weight 16 lbs)
- 17x10 ET45/ET40/ET25 (wheel weight 19lbs)
- 17x4.5 ET-20 (wheel weight 16 lbs)
- 15x10 ET45 - (wheel weight 16 lbs)
- 17x10 ET45/ET40/ET25 (wheel weight 19 lbs)
- 17x4.5 ET-20 (wheel weight 16 lbs)
-
VTT 2019+ BMW G2X Carbon Fiber Intake Lids
VTT is proud to offer carbon fiber intake lids for 2019+ BMW G2X platforms and the Toyota Supra.
BMW did an excellent job designing the factory intake system, and through testing we’ve found it is only mildly restrictive at elevated power levels. With that in mind, we chose to build on BMW’s original design rather than reinvent it—creating a factory-style carbon fiber intake lid paired with a high-flow, reusable cotton filter that maintains stock appearance while improving airflow.
Unlike cosmetic carbon pieces, these intake lids are constructed from 8 full layers of 100% carbon fiber, not a single cosmetic layer wrapped over plastic. Each lid is 1.3 mm thick, vacuum-formed with our VTT logo embedded into the carbon, and finished with a UV-resistant high-gloss clear coat to prevent yellowing and discoloration over time.
The optional high-flow filter features a heat-resistant silicone base and a pre-oiled cotton weave element, designed to capture contaminants while maintaining excellent airflow. Filters are fully serviceable and reusable, eliminating the need for replacements.
For customers wanting airflow improvements while keeping a completely stock appearance, the filter is also available separately here:
https://vargasturbo.com/product/vtt-bmw-toyota-b58-tu-high-performance-drop-in-air-filter-upgrade/ -
VTT is proud to offer 2020+ Toyota Supra Carbon fiber intake lids. BMW did a wonderful job designing these intakes and we have found they are only slightly restrictive at elevated power levels. With this in mind, we decided to just take their cues, and make a factory-style carbon fiber intake top with a high-flow cotton pre-oiled filter. These are 8 layers of 100% carbon, not a single layer wrapped over plastic, and they are 1.3MM thick with our logo vacuum printed onto the tops, with a UV-resistant gloss clear coating. This is not only strong but will resist discoloration for an extended period of time. The filters themselves are made with a heat-resistant silicone base, a high-flowing cotton weave element with a pre-oiled design to catch contaminates but allow free flow. Filters are available by themselves for a flow upgrade while keeping the stock look here – https://vargasturbo.com/product/vtt-bmw-toyota-b58-tu-high-performance-drop-in-air-filter-upgrade/ Complete CF Lid kit with Silicone intake tube, and billet adapter available here - https://vargasturbo.com/product/vtt-a90-91-supra-modular-silicone-intake-system/
-
VTT is proud to offer high-performance drop-in replacement filters for the BMW B58 TU, this includes G series BMW including Z4, A90/91 Toyota Suora, and. These filters are custom-made for VTT. They are made with a heat-resistant silicone base, and a high-flowing cotton weave element with a pre-oiled design to catch contaminates but allow free flow. We designed these to work with our Carbon Fiber intake Tops, but these filters will also work perfectly with the stock tops. We offer them in two colors. Red, and Black Features:
- 50 States Emissions Legal
- Easy to install in 15-30 minutes even for a novice
- Filters can be cleaned forever meaning never buy new filters
- Completely reversible if you ever want to remove
-
Unsure of the state of your CHRA's, whether brand new from a questionable source or rebuilt? Don't install them without having a proper High-Speed balance done! This is the #1 most critical factor when building a turbocharger, and is even more important for performance turbochargers or small twins that see a LOT of RPM. We use a Turbo Technics VS3 balancer, and balance most units down to under .5G Not all turbos will be able to pass a high-speed balancing test for any number of reasons (usually poor assembly, bent shaft, etc), if they will not pass, we will send you the specs they are in, and as close as we could get them. We then will give you the option to send them back, or we can disassemble, and rebuild them in-house using our other balancing, and assembly tools to ensure a properly built/balanced unit. The service is for most turbos, and we have the capability to balance most units, NOT ALL. If sending in twins please choose TWO as the quantity
UNITS MUST BE SENT IN WITH NO HOUSINGS, AND IN A CONDITION READY TO BE BALANCED, IF YOU NEED TO SEND IN COMPLETE TURBOS, WE CAN DISASSEMBLE, AND BALANCE FOR YOU, BUT AN EXTRA CHARGE WILL APPLY. IF THE UNITS ARE SENT IN A CONDITION WHERE THEY CAN NOT BE BALANCED WE WILL LET YOU KNOW THE PRICE TO GET THEM TO A STATE WHERE THEY CAN BE
-
VTT ultimate E8/9X ultimate rear brake conversion kit VTT is happy to announce its new rear brake conversion kits for the E8X/E9X platforms. We take what already exists on the market, and make it much more complete, and much more performance-oriented while keeping the clearance for those 15” wheels. This kit replaces your rear brake rotors and calipers to fit 15″ wheels. It includes lightweight VTT calipers to go from the single-piston factory caliper to race-inspired 4-piston calipers. While dropping up to a whopping 20 LBS of unsprung weight off the back of your vehicle!
Pictures are for REFERENCE ONLY. All kits will come with varying hardware, brackets, and mounting styles based on the platform.
-
VTT is proud to introduce our billet replacement for the BMW B58 factory plastic oil filter housing cap.
The OEM plastic cap is a known weak point that can crack or deform under heat and pressure. Our billet solution not only eliminates that failure risk, but also integrates a high-strength magnet to capture fine metallic particles from your oil — adding an extra layer of engine protection.
Key Features
-
Direct OEM Replacement – Retains all factory provisions for the filter basket, including the critical lower pins that ensure proper oil pressure bypass function.
-
Added Protection – Built-in magnet continuously pulls metal particles from your oil, helping maintain a cleaner lubrication system.
-
Premium Construction – CNC-machined from 6061-T6 aluminum for superior durability.
-
Anodized Finish – Available in four colors for corrosion resistance and engine bay style.
-
Complete Compatibility – Designed specifically for the BMW B58 platform.
Available Colors
-
Red
-
Black
-
Blue
-
Clear
-
-
Do you work on BMW engines across multiple platforms? Tired of modifying universal engine stand plates just to make them fit? Frustrated by losing access to the flywheel side once the engine is mounted?
We were too—so we built the solution.
The VTT BMW Engine Stand Plate is a true bolt-on design that keeps the flywheel end fully accessible while providing a strong, stable mounting solution for your engine builds.
Machined from solid 6061-T6 billet aluminum and anodized in five colors for long-term durability and corrosion resistance, these plates are lightweight yet rated for over 1200 lbs.
Fitment: N54, N55, S55, B58, S58 (more coming soon)
Note: The stand tube is 60mm or 2.36” OD, which fits most engine stands, but not all—please measure before purchasing.
Key Features:
- Lightweight, high-strength billet 6061-T6 construction
- Durable anodized finish
- Direct bolt-on to intake-side motor mount location
- Full clearance for accessories and flywheel/flex plate access
- Built-in provisions for locator pin and rotation bar
-
VTT “Ultimate” Front Drag Brake Kit
E-Series & F-Series BMW
Looking to make your E or F-Series BMW faster in the 1/4-mile or 1/2-mile?
Want to run 17" or even 15" front wheels?
Want to drop OVER 54 lbs of unsprung weight off the nose of the car while improving weight transfer — without breaking the bank?
The VTT Ultimate Front Drag Kit is engineered specifically for straight-line performance. This system allows you to run the wheel and tire combination needed to lower ETs while dramatically reducing unsprung and rotational mass compared to the factory steel front brake setup.
Less weight.
This kit comes in 1 variation, with two different caliper Options for each. We HIGHLY suggest 6-piston Calipers for street driving and 1/2 mile racing. These calipers will drop weight, AND be a braking upgrade over stock calipers.
More clearance.
Better weight transfer.
Faster passes.Pictures are for REFERENCE ONLY. All kits will come with varying hardware, brackets, and mounting styles based on the platform.
-
VTT Cone Filters feature High flow elements with a silicone body and a velocity stack built-in for smooth flow. We offer these filters in a variety of sizes for universal use. These are also replacement filters for VTT intake kits including B58 Gen 1, TU, Supra, Audi 4.0, N54 Dual Cone filter kit, etc Kit Includes:
- 1 - Cone Filter
- 1 - Clamp
-
THE DRIVESHAFT for the MK5 Supra!
Why overpay for a carbon fiber MK5 Supra driveshaft?
VTT is proud to offer a premium carbon fiber driveshaft manufactured exclusively for VTT in the USA by GCDS (Gulf Coast Driveshaft) — one of the premier driveshaft manufacturers in the country with extensive experience in high-performance and drag racing applications.
Each driveshaft is constructed using 3.25" carbon fiber tubing, paired with NEAPCO Performance 1350 series U-joints, then bonded using a proprietary high-strength process and precision balanced to within 1/8 in-oz as a complete assembly.
Every shaft is torque tested in-house prior to shipping to ensure proper bonding and structural integrity. GCDS and VTT are among the few manufacturers that perform full torque testing on each shaft before it leaves the facility.
To complete the system, the driveshaft is paired with VTT-designed 7075 aluminum adapters, eliminating the factory guibos and unnecessary flex points. The shaft connects directly to the BMW 3-bolt front flange, while a VTT 4340 rear adapter replaces the factory slip-in / screw-retained shaft design for improved strength and reliability.
Proudly Made in the USA.
PLEASE NOTE! Driveshafts can have UNUSUALLY LONG LEAD TIMES. We hope to reduce this with GCDS, but if the shaft shows OUT OF STOCK, expect a lead time of 4–8 weeks, unless we specifically state that it can ship sooner.
Due to the nature of these shafts being manufactured by a 3rd party, ANY ORDERS PLACED FOR VTT CF DRIVESHAFTS ARE 100% FINAL.
NO REFUNDS. NO CANCELLATIONS. FOR ANY REASON.
THIS INCLUDES LONG LEAD TIMES.
PLEASE ORDER CAREFULLY. ONCE THE ORDER IS PLACED, IT IS FINAL.
-
VTT Billet Aluminum Valve Cover – B58 TU
The Only Billet Valve Cover Option for the B58 TU Platform
VTT is proud to introduce our B58 TU Billet Aluminum Valve Cover, designed for enthusiasts looking to enhance both the performance and appearance of their engine bay.
The OEM plastic valve cover is known to crack over time and contains a problematic built-in PCV system. Our billet cover eliminates those issues and gives you complete modularity and control over your PCV setup.
We recommend pairing it with our B58 TU Catch Can Kit for the ultimate crankcase ventilation solution. Additional breather options—including our oil cap breather and one-way stainless breathers—are also available to further enhance your setup.
Key Features
-
100% CNC-machined 6061-T6 aircraft-grade aluminum
-
Anodized in a variety of durable color options
-
Lightweight at 9.7 lbs (vs. 7.9 lbs for the stock plastic cover)
-
Includes three shrouded -10 ORB ports for maximum PCV flexibility
-
Fully baffled ports to reduce oil carryover
-
Only billet option currently available for the B58 TU
-
Optional titanium hardware or OEM-style fasteners
-
-
VTT is proud to announce our B58 Gen 1 Billet/Silicone coolant hose upgrade kit! The factory plastic coolant connectors are prone to breaking over time, and the hoses are just your standard run-of-the-mill coolant hose. We wanted to provide an upgrade to both areas. What we came up with is Billet 6061-T6 connectors anodized black for corrosion resistance, and 6-ply silicone molded silicone hoses in the factory shapes. Currently, these fit most Gen 1 B58 applications F2X/F3X. Application chart below.
They may not fit some models, we have not test fit on all models.
Please bear in mind, the B58 coolant hoses can be difficult to install, and may require removal of other items on the engine to reach the hose connections.
-
The Factory B58 TU water neck is plastic and is right in the path of your charge pipe if you lose a connection and it blows off. If this does happen to you it can break the plastic neck emptying your coolant in seconds causing you in the best-case scenario to be stranded, and in the worst-case scenario expensive engine damage. Add some cheap insurance with our Billet Water neck.
-
Give the Gift of VTT! Looking to get your friends, or family some go-fast parts, and no idea what they need, only that they love VTT? Well, our Gift Cards have you covered! They come in $50, $100, $250, $500, and $1000 increments. Each gift card is precision cut out of plastic in the shape of the VTT logo and has the dollar amount and the code on the back. Each gift code is unique and is locked to that card. To redeem simply enter the code during check out it will remove that amount, and if you have any leftover it will go back to the card.
You can choose to have your card physically mailed to you, or a virtual card where we can send you a scan of your card.
-
VTT is proud to offer high-performance drop-in replacement filters for the F Series BMW B58. These filters are custom-made for VTT. They are made with a heat-resistant silicone base, a high-flowing cotton weave element with a pre-oiled design to catch contaminates but allow free flow. We designed these to work with our Carbon Fiber intake Tops, but hese filters will also work perfectly with the stock tops. We offer them in two colors. Red, and Black Features:
- 50 States Emissions Legal
- Easy to install 15-30 minutes even for a novice
- Filters can be cleaned forever meaning never buy new filters
- Completely reversible if you ever want to remove
-
VTT is proud to announce another product in our carbon fiber product line. The BMW F-Series B58 Modular Carbon fiber intakes system! We COMPLETELY do away with the entire factory intake tract, including the accordion hose, the turbo muffler, all of the restrictive bends. We then replaced it with a smooth radius 2.5"-4" Silicone intake pipe with wire impregnated to ensure strength and longevity. This is coupled with our billet intake connection for an OEM-like fit, and finish. We then created a 100% carbon factory-style intake top and coupled it with our high-flow cotton pre-oiled filters. These tops are 8 layers of 100% carbon, not a single layer wrapped over plastic and they are 1.3MM thick with our logo vacuum printed onto the tops, with a UV-resistant gloss clear coating. This is not only strong but will resist discoloration for an extended period of time. The filters themselves are made with a heat-resistant silicone base, a high-flowing cotton weave element with a pre-oiled design to catch contaminates but allow free flow. But we didn't stop there! For the crowd looking for increased intake sound, we also made this compatible with our 4" Cone filter for increased flow, and much louder intake sound! These are available for stock, AND aftermarket turbos. Filters are available by themselves for a flow upgrade while keeping the stock look here - https://vargasturbo.com/product/vtt-f-series-bmw-b58-high-performance-drop-in-air-filter-upgrade/ Features:
- Completly modular, can switch from Carbon top to Cone filter all using our silicone intake tube
- 50 States Emissions Legal (Carbon fiber top kit only. The Cone filter option is legal for racing use only in California. Always follow all local emissions rules)
- Easy to install 15-30 minutes even for a novice
- A Beautiful Carbon Fiber finish really adds class to the B58 engine bay
- Filters can be cleaned forever meaning never buy new filters
- Completely removes the restrictive stock intake pipe, NOT only the turbo muffler elbow
- Completely reversible if you ever want to remove
-
Looking for some more fuel for your B58 powered BMW? Not looking to break the bank on overpriced PI kits? PFS has you covered with its Plug, and play PI kit for the B58.
-
VTT is proud to offer Titanium wheel stud kits for the owner looking for the lowest possible unsprung weight while maintaining high strength, and good looks as all come with an amazing burnt finish. This kit is 60% lighter than factory steel studs and nuts with a total kit of 20 nuts, and studs being 3.1LBS. Sets of 10 are 1.55 lbs
-
Need to work on the B58 engine outside of the car? Lift it to put on an engine stand etc? BMW makes an engine lifting tab but it costs $25, and they do not always have them in stock. We made our own, to avoid the high cost, and possibly long wait time. The perfect tool when you want to lift the engine balanced in the place BMW designed for it to be lifted. Made out of coated steel for high strength, long life, and corrosion resistance. Fits all B58 models, and possibly S58
-
Do you work on a lot of BMW engines from various platforms? Do you ever struggle with heavy cylinder heads, either lifting off the engine or simply moving around? Ever ruined an EXPENSIVE multi-layer head gasket while trying to install a cylinder head due to no secure way to hold it without two people? We answered yes to all of those things, and came up with a tool for anyone that works on BMWs often, and needs a way to simply, and easily remove/install, or simply move around a cylinder head. These cylinder head tools are machined from a solid billet of 6061-T6 aluminum and anodized in 4 colors for long-lasting corrosion resistance. They are knurled for a non-slip grip when oily or wet, and positioned so the head is balanced when lifting The Head Handler fits the following engines, N54, N55, S55, B58, S58 and we offer short extensions for installation with no cams/Cam ledges on the head, or long extensions for people that want to install or remove a head with cams still installed. (B58 only requires short extensions)
-
VTT offers silicone hoses in various Push-lock sizes, we use these for our catch can kits, but they are also suitable for coolant, vacuum, boost, etc. Do not use with fuel. We offer: -10 Push Lock 24", and 18" -8 Push Lock 24", and 19.5" -6 Push Lock 24"
-
VTT Billet & Forged Carbon Strut Bar – BMW G2X Platform (2019+)
We took our popular VTT Billet G8X Strut Bars and redesigned them specifically for the BMW G2X platform. This is not a metal bar wrapped in carbon overlay — it’s a true forged carbon fiber strut bar engineered for both performance and appearance.
Each unit features CNC-machined billet ends crafted from 6061-T6 aluminum or Grade 2 Titanium, providing exceptional strength and precision. Every bar is anodized or polished to perfection and available in Black, Red, Blue, or genuine T2 Titanium rainbow finish.
This upgrade dramatically enhances underhood aesthetics while maintaining proper chassis rigidity and fitment across all 2019+ G2X vehicles.
Key Features
-
Real Forged Carbon Fiber Center – 100% forged carbon, not a metal core with a carbon wrap.
-
Billet Aluminum or Titanium Ends – CNC-machined from 6061-T6 aluminum or T2 Titanium for unmatched durability and strength.
-
Premium Finishes – Choose from Black, Red, Blue anodized, or genuine T2 Titanium rainbow finish.
-
Direct Bolt-On Fitment – Designed to install directly using OEM mounting points. No modification required.
-
-
VTT is proud to offer the PFS A90/91 Supra upgraded LPFP line. This line replaces the factory line from the tank to the hard-line under the drivers feet with a line which increases diameter 22%, and volume/area 56% over factory line. The factory line is just under 8mm ID the PFS line uses genuine Parker 801-6 hose which is 10mm ID. This is a plug-and-play option. Remove your factory line, and install this line in its place, it will fit in all the line holders.
-
VTT Billet & Forged Carbon Strut Bar – A90/A91 Toyota Supra
Building on the success of our Billet G8X Strut Bars, VTT has now engineered a version specifically for the A90/A91 Toyota Supra. This design is a true evolution — not a metal bar wrapped with carbon overlay, but a genuine forged carbon fiber center section paired with precision-machined billet ends.
Each end is CNC-machined from either 6061-T6 aluminum or Grade 2 Titanium, ensuring exceptional strength, rigidity, and long-term durability. Every piece is finished in-house and anodized in your choice of Black, Red, Blue, or genuine T2 Titanium rainbow finish.
This is a true performance and visual upgrade — not just an accent piece.
Key Features
-
Real Forged Carbon Fiber Construction – No metal core or cosmetic overlay; this is a full forged carbon center section.
-
Billet Aluminum or Titanium Ends – CNC-machined from 6061-T6 aluminum or T2 Titanium for maximum precision and strength.
-
Premium Finishes – Choose from Black, Red, Blue anodized, or genuine T2 Titanium rainbow finish.
-
Direct Fit Design – Installs using factory mounting points; designed for a perfect fit on the A90/A91 Supra.
-
-
Tired of getting off the dyno, and having your drivetrain malfunction light on due to a broken plastic ride height bracket? So were we, after we broke 3 of them, we knew it was time to make our own to combat the issue. This bracket is cut from 6061-T6 for strength and anodized black for a long-lasting finish.
-
Improve engine/shifting feel without a huge increase in NVH or high cost! VTT A9X billet motor mount inserts upgrade mounts the way BMW does it, allowing a minimal increase in NVH while stiffening up the engine/shifting feel, and getting rid of excessive engine movement
-
VTT Billet B58 Gen PCV Cap replacement. Get rid of your fragile Stock PCV Cap/Diaphragm
-
VTT is proud to offer a Titanium hardware upgrade for all our Billet and Cast VC's. This will come with M6x30 Ti bolts N54 /N55/S55/B58 Gen 1/ B58 TU it will be an Umbrella head with a 16.3mm head. These bolts weigh half as much as comparable steel hardware and look amazing. Colors to choose from will be Burnt, Black, and Natural (silver)
-
VTT Billet Aluminum Valve Cover – B58 Gen 1
Performance, Reliability, and Style for the B58 Gen 1 Platform
VTT is proud to introduce our B58 Gen 1 Billet Aluminum Valve Cover, engineered for enthusiasts seeking both performance and reliability. This cover replaces the factory plastic unit, which is known to crack and incorporates a restrictive PCV system. Our billet design eliminates those weaknesses while giving you complete control over your crankcase ventilation setup.
We recommend pairing this valve cover with the VTT B58 Catch Can Kit for maximum performance and crankcase pressure management. Additional breather options—including our oil-cap breather and one-way stainless breathers—are also available to fine-tune your configuration.
Key Features
-
100 % CNC-machined 6061-T6 aircraft-grade aluminum
-
Multiple anodized color options, with custom finishes available
-
Lightweight design – 9.7 lbs (vs. 7.9 lbs for the stock cover)
-
Fully baffled internal system to minimize oil carryover
-
Fully modular PCV configuration for complete ventilation control
-
The only billet valve-cover option currently available for B58 Gen 1
-
-
Need a replacement filter for your VTT Billet Crankcase breather? You can order on here. We offer them in 3 heights, low 48mm, medium58mm, and tall 68mm. This is measured from base to top. The filter will include a new clamp. For reference: N54/55 mostly use the low A90 Supra use Medium Most Audi applications can fit a tall, but measure your filter before ordering.
-
VTT Modular Silicone/Billet Intake System – BMW G2/3/4X B58TU
VTT is proud to announce our Modular Silicone/Billet Intake System for the BMW G2/3/4X platforms equipped with the B58TU engine.
After extensive testing and countless hours of fitting, we’ve created an intake system that delivers both optimized airflow and factory-level fitment.
Why Upgrade?
The factory BMW airbox itself performs well, but the intake tract down to the turbo is full of twists, turns, bellows, and even a built-in silencer that restricts flow and robs power. Our system eliminates these bottlenecks and replaces them with a 3"–3.5" free-flowing silicone intake tube, paired with either:
-
The stock airbox (for OEM appearance and sound), or
-
Our 6" high-flow cone filter with integrated velocity stack (for maximum airflow and sound).
From testing, we’ve confirmed the stock airbox is capable of supporting up to 700WHP. Beyond that, we recommend stepping up to the 6" cone filter system.
-
-
VTT Modular Silicone/Billet Intake System – Toyota A90/91 Supra (B58TU Engine)
VTT is proud to announce our Modular Silicone/Billet Intake System for the A90/91 Toyota Supra with the B58TU engine.
After countless hours of testing and fitting, we’ve engineered an intake that delivers both optimized airflow and OEM-level fitment.
Why Upgrade?
The factory Supra airbox is efficient, but the intake tract to the turbo is a problem area. It’s full of twists, turns, and accordion bellows that disrupt airflow, plus a built-in silencer that restricts performance by bypassing air simply to quiet intake sound.
By replacing these with our 3"–3.5" free-flowing silicone intake tube, paired with your choice of:
-
The stock airbox (for factory sound/appearance),
-
Our 6" cone filter with built-in velocity stack (for maximum airflow and sound), or
-
Our Carbon Fiber Airbox Lid with high-flow panel filter,
…you remove restrictions and create a smooth, optimized air path straight to the turbo.
Our testing shows that the stock airbox supports up to ~700WHP. Beyond that, we recommend upgrading to the 6" cone system for maximum efficiency.
-
-
PFS is proud to offer a true drop-in 800-1000WHP+ capable LPFP for A90/91 Toyota Supras. This LPFP needs NO additional pumps, wiring harnesses, etc etc. It will support up to 800WHP on Ethanol percentages as high as E98 and will support much higher power levels with less E content as long as you have the octane to support it. For the pump, we start with a factory bucket, we modify it extensively to accept our custom PFS Brushless fuel pump. We then re-terminate the factory wiring to accept the new pump. No wiring splices, done the same way the factory does -the right way.
-
Need to replace the gasket on your VTT Aluminum VC? Simply choose your model from the dropdowns to ensure you get the correct version.
-
VTT Billet Wheel Spacers
VTT is proud to offer billet wheel spacers for most VAG, BMW, and the A90/91 Toyota Supra platforms.
Each spacer is:
-
CNC-machined from 6061-T6 aluminum
-
Hard anodized black for a long, corrosion-free life
We offer multiple fitments and sizes to suit a wide range of applications.
THESE ARE SOLD INDIVIDUALLY, FOR ONE AXLE ORDER TWO FOR A COMPLETE SET ORDER FOUR.
ANYTHING OVER 5MM WILL REQUIRE LONGER BOLTS OR STUDS. YOU CAN CHOOSE TO ADD A VTT WHEEL STUD KIT FROM THE OPTIONS.
PLEASE DOUBLE CHECK YOUR BOLT PATTERN AND HUB BORE BEFORE YOU ORDER. INSTALLED SPACERS CANNOT BE RETURNED!
-
-
Racing can be rough on brake pads, if you have worn through a set of pads while using your VTT brake kit you can buy replacement pads here. Different options are available as shown below. Please take a look at your pads to see the hole orientation which will determine your pad type BP-10 pads for Dynalite calipers Single hole in the pads for the location pin - Mostly street and some racing we recommend for rear kits BP-20 pads for Dynalite calipers Single hole in the pads for the location pin - More aggressive street driving, and racing recommended for front or rear kits BP-10 pads for Dynapro calipers with twin holes in the pads for the location pins - Mostly street and some racing we recommend for rear kits BP-20 pads for Dynapro calipers with twin holes in the pads for the location pins - More aggressive street driving, and racing are recommended for front or rear kits Hawk PC (Performance Ceramic) Very Quiet, Very low dust, Hawk claims 32% increase in stopping power over stock pads. A good balance of street, and aggressive driving. Recommended for front or rear kits
MANY MORE AGGRESSIVE BRAKE PAD COMPOUNDS EXIST FROM VARIOUS MANUFACTURERS, AND YOU CAN TAILOR TO YOUR NEEDS. Y OU CAN FIND THESE BY USING THE CALIPERS STYLE NUMBERS BELOW.
6-PISTON DYNAPRO PAD STYLE 6712
4-PISTON DYNAPRO PAD STYLE 7812
-
Looking to convert your 5x112 M14x1.25 vehicle, such as A90/91 Toyota Supra, and 2020+ BMW G-series, to 5x114 to open up your wheel options? We got covered with our VTT wheel stud conversion kits. These kits are forged cold-rolled steel in 10.9 class, with Black Oxide corrosion-resistant coating for years of use, and convert your vehicle to M12x1.50 wheel studs, which allow you to fit 5x114 wheels with no other changes. No wobble bolts or redrilling here. Simply install the studs, put the wheel on, and the lug nuts will center the wheel. This kit is Black Studs with Black Lugnuts, and we offer it in 10 or 20 pieces if you want to only do the front/rear or both.
Our studs are forged from cold-rolled 10.9-class steel and finished with a black oxide corrosion-resistant coating, ensuring years of dependable service in both street and motorsport environments.
We offer one optimized size: 85mm overall length, with the following breakdown:
-
75mm total thread length
-
10mm bull nose for smooth lug engagement
-
12mm short-thread section (hub side)
-
12mm unthreaded shank
-
48mm long-thread section (lug nut side)
PLEASE NOTE – THESE STUDS WILL ONLY WORK IF YOUR WHEELS ARE DRILLED M14 THESE WILL NOT WORK FOR WHEELS DRILLED M12!
These studs are coated using Black Oxide, which does protect, BUT even when using Black Oxide, the studs CAN develop surface rust if left to the elements. We suggest a slight coat of WD-40 when you clean your wheels to prevent this.
DO NOT USE ANY HUB-CENTERING SLEEVES WITH THESE CONVERSION STUDS, THE LUGS WILL CENTER THE WHEELS. THE USE OF A CENTERING SLEEVE MAY LEAD TO STUDS BREAKING. FOR INSTALLATION YOU MUST SNUG EACH LUG UP SLOWLY, AND IN A STAR PATTERN TO GET THE WHEEL CENTERED ON THE LUGS, FAILURE TO DO SO CAN ALSO LEAD TO FAILURE.
-
-
Out of stockVTT Is proud to offer a seamless Chromoly Driveshaft for the A90/91 Supra. This driveshaft is made from seamless 4130 Chromoly steel and forged 4130 weld ends, and Spicer 1350 Yolks, and U-Joints. All pieces are then precision tig welded, and balanced. We couple the driveshaft with VTT Custom 7075 aluminum adapters which convert the 3 bolt BMW bolt pattern to the 4 bolt Spicer yolk patter. This driveshaft is rated at 4100 ft/lbs of Tq, and more than 10,000RPM.
-
Our studs are forged from cold-rolled 10.9-class steel and finished with a black oxide corrosion-resistant coating, ensuring years of dependable service in both street and motorsport environments.
We offer one optimized size: 85mm overall length, with the following breakdown:
-
75mm total thread length
-
10mm bull nose for smooth lug engagement
-
12mm short-thread section (hub side)
-
12mm unthreaded shank
-
48mm long-thread section (lug nut side)
These studs are coated using Black Oxide, which does protect, BUT even when using Black Oxide, the studs CAN develop surface rust if left to the elements. We suggest a slight coat of WD-40 when you clean your wheels to prevent this.
These studs are coated using Black Oxide, which does protect, BUT even when using Black Oxide, the studs CAN develop surface rust if left to the elements. We suggest a slight coat of WD-40 when you clean your wheels to prevent this.
-
-
VTT Billet Oil Cap – BMW S58 & B58TU
Ditch the factory plastic and upgrade to a true performance piece. The VTT Billet Oil Cap is CNC-machined from solid 6061-T6 aluminum and anodized in your choice of vibrant finishes. Unlike snap-on covers, this is a complete replacement cap engineered for strength, precision, and long-term reliability.
-
Premium Materials – 6061-T6 aircraft-grade aluminum with precision machining.
-
Functional Design – Direct replacement for the OEM cap with proper sealing and durability.
-
Anodized Finishes – Available in five colors to match or contrast your build.
-
High-End Look – Adds a clean, motorsport-inspired aesthetic to your engine bay.
Fitment
Designed specifically for all BMW S58 and B58TU G-Series engines, including (but not limited to):-
G8X M3 / M4
-
Toyota A9X Supra
-
All G-Series 2, 3, 4, 5, 7, 8, and X models
A simple upgrade that delivers both style and substance—because your BMW deserves more than plastic.
-
-
VTT Is proud to offer the BC stroker kit for the Toyota B58B30 engine platform that incorporates a 100mm stroke, steel billet crank, BC 4340 Pro Series Heavy-Duty connecting rods rated to 1600+ horsepower.
-
VTT is proud to announce our F/G Series B58 engine catch can set up. This kit uses our already extremely popular modular catch can, and couples it with a custom CNC 6061 bracket, VTT CNC banjo fittings, VTT 5 ply silicone hose, and Push lock fittings. Install is simple, takes about 30 minutes to 2 hours depending on your skill level, and requires removing one factory hose to install the VTT hoses. Giving an OEM fit and finished when installed. Our kit stands out from others on the market by using high-quality AN fittings, and VTT Banjo adapters. G series fits all 2019+ G Series 3/4 BMW vehicles with the B58TU engine, F Series fits all 2015+ F3X series BMW vehicles with the B58 engine. May NOT fit all F series as some 2 series chassis may be different.
-
NGK 94201 Spark Plug Set — compatible with all S58 / B58 / B48 applications, and also ideal for N54 / N55 platforms running the B58 coil upgrade.
We recommend these plugs for vehicles running 100% E85, high boost, or upgraded ignition setups. They are an excellent choice for high-performance BMW applications including N54, N55, and S55 (with B58 coils), and they also serve as a great maintenance replacement for any S58/B58/B48-powered vehicle — at a significantly better price than most options on the market.
Plugs are sold as a set of 6.
Pre-gapping is available for an additional charge -
VTT “GC” Rear Drag Brake Kit
A90 / A91 Toyota Supra
Looking to make your A90/A91 Supra quicker in the 1/4-mile or 1/2-mile?
Want to run 17” or even 15” rear wheels with only minor suspension modification?
Want to drop up to 35 lbs of unsprung weight from the rear of the car — without breaking the bank?
The VTT “GC” Rear Drag Kit is designed specifically for straight-line performance. This kit allows you to run the wheel and tire combination you need to lower ETs while significantly reducing rotational and unsprung mass compared to the factory rear brake setup.
Less weight.
More clearance.
Better weight transfer.
Faster passes.
Fitment
-
2020+ Toyota Supra A90/A91 (B58 platform)
-
Confirmed fitment on many BMW G-Series chassis, including G20, G42, and others.
(Contact us to confirm your specific chassis.)
Notes
-
Minor suspension modification may be required for certain wheel/tire combinations.
-
Photos shown are for reference only.
-
Hardware, brackets, and mounting configurations may vary by platform.
-
-
VTT “GC” Front Drag Kit – A90/91 Toyota Supra / G Series BMW
Looking to make your A90/91 Supra faster in the ¼ mile or ½ mile? Want to run 17” wheels (or even 15” with suspension modifications) and front skinnies? How about shedding nearly 70 lbs of unsprung weight from the front of the car — without breaking the bank?
Look no further than the VTT “GC” Front Drag Kit. This kit is designed specifically for drag racing, giving you the wheel/tire setup you need to drop ETs while putting your Supra on a serious diet compared to the heavy OEM front brakes.
Pictures are for REFERENCE ONLY. All kits will come with varying hardware, brackets, and mounting styles based on the platform.
-
VTT ultimate F3X ultimate rear brake conversion kit
VTT is happy to announce its new rear brake conversion kits for the F3X platforms. This is the FIRST and only kit currently on the market that will allow 15" wheels and tires to be run on the rear. This kit replaces your rear brake rotors and calipers to fit 15" wheels. It includes lightweight VTT calipers to go from the single-piston factory caliper to race-inspired 4-piston calipers. At the same time, dropping up to a whopping 20 LBS of unsprung weight off the back of your vehicle!
Pictures are for REFERENCE ONLY. All kits will come with varying hardware, brackets, and mounting styles based on the platform.
-
Looking to maximize your F or G Series BMW for drag racing? Want to be able to dial in the perfect amount of compression or rebound on your launch? The VTT Double adjust drag shock kit is just want the doctor ordered!
-
Looking to maximize your A90/91 for drag racing? Want to be able to dial in the perfect amount of compression or rebound on your launch? The VTT Double adjust drag shock kit is just want the doctor ordered!
-
These are the same premium pistons we use in our winning race and high-performance street engines around the world! We feel that these are the best pistons for your high performance or racing engine.
-
Carrillo connecting rods are well known within pro racing and street performance circles for good reason; they produce a premium product that winning racers around the world depend on.
-
VTT is proud to announce our A90/91 Supra engine catch can set up. This kit uses our already extremely popular modular catch can, and couples it with a custom CNC 6061 bracket, VTT CNC banjo fittings, VTT 5 ply silicone hose, and Push lock fittings. Install is simple, takes about 30 minutes to 2 hours depending on your skill level, and requires removing one factory hose to install the VTT hoses. Giving an OEM fit and finished when installed This catch can fits all known intake variations we have seen, including stock intake. Kit Break down is as follows:
- One Catch Can
- One CNC 6061 bracket
- Two -10 Low Profile CNC Banjo Fittings
- Two -10 VTT 5-Ply silicone Vacuum hoses
- Two -10 Push Lock Fittings
- Two spring clamps
- Available with an optional Drain fitting, allowing quick draining
-
VTT B58 A90/91 Supra Billet One Way Crankcase Breather
VTT is happy to introduce the first and only available plug-and-play ONE-WAY crankcase breather kit for BMW B58TU A90/91 Supra applications. The B58 engine is known for poor PCV and crankcase pressure issues. With this breather simply remove your oil cap, install the breather, and instantly free up horsepower, improve turbo draining, remove crankcase pressure, all while adding a cool look to your engine bay. FITS with the engine cover on. Engine cover can be removed, and installed without removing the breather.This is a SERVICE item, it is designed to capture and hold oil that is pulled from the spent gasses when it gets saturated, it must be cleaned
-
We are happy to release our BMWB58 (Fits ALL B58 models including TU found in the A90/A91 Toyota Supra) vacuum/boost adapter. These go inline with the intake manifold fitting and provide a full boost/vacuum signal from the manifold. This fitting adds two 1/8NPT bungs to accept any fitting that has 1/8" NPT threads. You can choose options, Fitting by itself, 1/4" barb, as well as 1/8NPT plugs if you only want one barb, etc. You can choose straight or 90-degree barbs. Once installed it tucks perfectly under your engine cover. These are perfect for running your PI switch off manifold pressure which is much more accurate than charge pipe, and they are also great for BOV running the proper size line without having to drill a hole in your manifold. These do space out any sensors etc giving inaccurate readings like some of the other brands do. They are made from 6061-T6 anodized black, with steel plugs, and Blue Anodized barbed fittings. You can choose to order in a few ways. Adapter alone - $40 Basic kit - 1 Adapter, 1 barb, and one plug $45.00 Dual Barb kit - 1 Adapter, 2 barbs, $55.00
-
VTT B58 Gen-1/TU Billet One-Way Crankcase Breather
VTT is proud to introduce the first and only plug-and-play ONE-WAY crankcase breather kit for BMW B58 applications! (For Supra applications, please check our Supra section.)
This breather is a simple yet effective upgrade—just remove your oil cap, install the breather, and instantly free up horsepower. It improves turbo draining, eliminates crankcase pressure, and enhances your engine bay's aesthetics. Fits with the engine cover on, and you can remove/install the cover without taking off the breather.
Key Features & Benefits:
✅ Easy Installation – Plug-and-play design; installs in minutes
✅ Reduces Crankcase Pressure – Improves turbo performance & engine efficiency
✅ Compatible with Stock or Aftermarket PCV Systems – Can be used alone or paired with the VTT Engine Catch Can for maximum crankcase pressure relief
✅ High-Quality Construction –- 6061-T6 Aircraft-Grade Aluminum with a durable black anodized finish
- Four Stainless Steel Baffles for superior oil control
- PTFE One-Way Check Ball to ensure proper ventilation
- Premium Filter & Clamp to maintain performance and longevity
Maintenance Advisory
- This is a service item—it captures oil from spent gases, so it must be cleaned periodically.
- Vehicles with high crankcase pressure may require more frequent cleaning to prevent oil mist from escaping.
-
Please note: Due to heavy increases in freight costs we have had to raise prices by $50 on 54-gallon drums, and $15 on pails.
VTT is proud to be the West Coast dealer for One Ethanol racing fuel.
We have two blends available in 5-gallon pails and 54-gallon drums. See below for descriptions of both fuels
Fuel is available for local pick up only unless you email, and make arrangements for freight shipping. Be aware fuel is considered hazmat and the freight charges are equal to or more than the fuel in all instances. Fuel CANNOT be shipped normal shipping methods such as UPS, FED EX, etc
