-
Introducing the VTT OBD-LOCK – Enhanced Security & Improved Design!
We are excited to announce our OBD-LOCK! This latest version has been completely redesigned for improved strength, ease of installation, and enhanced protection. Key upgrades include:
No more OBD port penetration – eliminates any risk of damage
Revised thread style – prevents stripping for a secure fit
Stronger, more durable design – ensures maximum securityUltimate OBD Port Protection
The VTT OBD-LOCK is precision-machined from billet 6061-T6 aluminum and is engineered to completely lock out your OBD port, preventing unauthorized access.
Anti-Theft Protection – Prevents thieves from accessing the OBD port to duplicate keys or disable security systems
Dealer/Tech Lockout – Stops unauthorized tune changes or system modifications
Tamper-Proof Design – Cannot be removed without physically destroying the OBD port unless the correct tool is usedVTT OBD-LOCK – Version 2 NON-GM
Universal Fit for All Non-GM (General Motors) VehiclesThis device is compatible with all non-GM vehicles, including but not limited to:
-
All VAG group vehicles (VW, Audi, Bentley, etc.) — including recessed port VW/Audi models
-
Ford, Nissan, Honda, Toyota, Porsche, Dodge, Ram, Jeep, Kia, Subaru, and more
Not compatible with GM (General Motors) vehicles.
VTT OBD-LOCK – Version 2 GM
Universal Fit for GM (General Motors) Vehicles ONLYThis version is specifically designed for General Motors vehicles, including GM, Chevrolet, Cadillac, Holden, and other GM-branded models.
If your vehicle is anything other than a General Motors product, you will need the Non-GM version.
-
-
VTT Universal Turbo Fittings – Oil & Coolant Solutions for BMW Turbo Builds!
Looking to fabricate your own turbo kit for BMW platforms? Need an easy solution to block off water lines or create custom feed and drain fittings? Look no further! VTT offers a wide range of high-quality oil and coolant fittings to simplify your build. Our fittings are designed for most late-model BMW platforms, providing a plug-and-play solution for custom turbo setups. 📌 Available Fitting Options: 🔹 Oil Feed – -4 AN Male 🔹 Oil Drain – -10 AN Male 🔹 Coolant Fittings – Barbed Male or Block-Off Options -
VTT CNC Billet check valve that can be used for a variety of uses including a vacuum/boost check valve when removing the stock PCV system, and still wanting to run vacuum to the crankcase. Rated at over 100 psi, with a cracking psi of .25psi.
-
Are you building a single kit for the N54, N55, or S55 platform? The stock studs are usually a little bit short for most single-head flanges, and finding M7 studs is not easy. So we made our own longer studs to combat the issue. Made from 10.9 grade steel, and coated in black oxide, these are the perfect solution to the short stud problem. Sold individually so order the number you need. Stud details are as follows
- Overall length 47mm (stock 39mm)
- 3mm shoulder
- 6mm head which is 5mm hex
- 14mm short end
- 24mm long end (stock 15mm)
Dont forget our M7 copper lock nuts as well to complete the job - https://vargasturbo.com/product/vtt-fab-m7-copper-locking-exhaust-nuts/
-
VTT High-Performance Ignition Coils
BMW N5X • B58 / S58 / B48 • VAG Platforms
Vargas Turbo Technologies (VTT) is proud to offer high-performance ignition coil upgrades for BMW N5X platforms, B58/S58/B48 engines, and select VAG applications.
Development & Testing
Our ignition coil program began with extensive outreach to multiple OEM and aftermarket coil manufacturers. We commissioned individual prototype coils, then subjected them to rigorous, repeatable testing in the United States to ensure they matched or exceeded factory performance standards.
Only the highest-performing designs were selected and produced to VTT’s exact specifications and colorways. These are not rebranded or cosmetic coils—each set is performance-validated.
-
Are you building a single kit for the N54, N55, or S55 platform? M7 Locking exhaust nuts is not easy. So we made our own to combat the issue. These are the perfect solution to the problem of hard-to-find M7 lock nuts. Sold individually so order the number you need.
Note: This is nuts ONLY Stud not included, by our extended M7 studs here - https://vargasturbo.com/product/vtt-fab-extended-m7-n54-n55-s55-b58-2-port-head-studs/
-
NGK 94201 Spark Plug Set — compatible with all S58 / B58 / B48 applications, and also ideal for N54 / N55 platforms running the B58 coil upgrade.
We recommend these plugs for vehicles running 100% E85, high boost, or upgraded ignition setups. They are an excellent choice for high-performance BMW applications including N54, N55, and S55 (with B58 coils), and they also serve as a great maintenance replacement for any S58/B58/B48-powered vehicle — at a significantly better price than most options on the market.
Plugs are sold as a set of 6.
Pre-gapping is available for an additional charge -
Looking to convert your 5×120 or 5x112 vehicle to 5x114.3 wheels, or 5x120 wheels, and open up your wheel options DRAMATICALLY? We got covered with our VTT wheel spacer conversion kits. These kits are machined from billet 6061-T6 aluminum and anodized for a long-lasting finish. We then press in 10.9 class studs, with corrosion-resistant zinc coating for years of use. The spacer then accepts either a 5x114 wheel or a 5x120 wheel. The 5x114 use M14 studs, and the 5x120 use M12 studs. All the spacers have either a 66.6mm or 72.6mm Hub bore size to fit 99% of BMW applications.
QTY 1 is for ONE SPACER. If you need to do 4 wheels order FOUR!
We offer Hub-Centric adapter rings to fit other wheel bore sizes No wobble bolts or redrilling here. We offer these in 4 thicknesses 15mm, 17.5mm, 20mm, and 25mm. The studs coming out of the spacer are 40″ total length and come with Black Lugnuts. Spacers that convert to 5x120 have M12 studs, ALL others have M14x1.5 -
VTT B58 A90/91 Supra Billet One Way Crankcase Breather
VTT is happy to introduce the first and only available plug-and-play ONE-WAY crankcase breather kit for BMW B58TU A90/91 Supra applications. The B58 engine is known for poor PCV and crankcase pressure issues. With this breather simply remove your oil cap, install the breather, and instantly free up horsepower, improve turbo draining, remove crankcase pressure, all while adding a cool look to your engine bay. FITS with the engine cover on. Engine cover can be removed, and installed without removing the breather.This is a SERVICE item, it is designed to capture and hold oil that is pulled from the spent gasses when it gets saturated, it must be cleaned
-
VTT Billet Wheel Spacers
VTT is proud to offer billet wheel spacers for most VAG, BMW, and the A90/91 Toyota Supra platforms.
Each spacer is:
-
CNC-machined from 6061-T6 aluminum
-
Hard anodized black for a long, corrosion-free life
We offer multiple fitments and sizes to suit a wide range of applications.
THESE ARE SOLD INDIVIDUALLY, FOR ONE AXLE ORDER TWO FOR A COMPLETE SET ORDER FOUR.
ANYTHING OVER 5MM WILL REQUIRE LONGER BOLTS OR STUDS. YOU CAN CHOOSE TO ADD A VTT WHEEL STUD KIT FROM THE OPTIONS.
PLEASE DOUBLE CHECK YOUR BOLT PATTERN AND HUB BORE BEFORE YOU ORDER. INSTALLED SPACERS CANNOT BE RETURNED!
-
-
Need to replace the gasket on your VTT Aluminum VC? Simply choose your model from the dropdowns to ensure you get the correct version.
-
Need a replacement filter for your VTT Billet Crankcase breather? You can order on here. We offer them in 3 heights, low 48mm, medium58mm, and tall 68mm. This is measured from base to top. The filter will include a new clamp. For reference: N54/55 mostly use the low A90 Supra use Medium Most Audi applications can fit a tall, but measure your filter before ordering.
-
Do you work on BMW engines across multiple platforms? Tired of modifying universal engine stand plates just to make them fit? Frustrated by losing access to the flywheel side once the engine is mounted?
We were too—so we built the solution.
The VTT BMW Engine Stand Plate is a true bolt-on design that keeps the flywheel end fully accessible while providing a strong, stable mounting solution for your engine builds.
Machined from solid 6061-T6 billet aluminum and anodized in five colors for long-term durability and corrosion resistance, these plates are lightweight yet rated for over 1200 lbs.
Fitment: N54, N55, S55, B58, S58 (more coming soon)
Note: The stand tube is 60mm or 2.36” OD, which fits most engine stands, but not all—please measure before purchasing.
Key Features:
- Lightweight, high-strength billet 6061-T6 construction
- Durable anodized finish
- Direct bolt-on to intake-side motor mount location
- Full clearance for accessories and flywheel/flex plate access
- Built-in provisions for locator pin and rotation bar
-
VTT offers silicone hoses in various Push-lock sizes, we use these for our catch can kits, but they are also suitable for coolant, vacuum, boost, etc. Do not use with fuel. We offer: -10 Push Lock 24", and 18" -8 Push Lock 24", and 19.5" -6 Push Lock 24"
-
Stop the Flex. Launch with Confidence.
Soft bushings are the enemy of hard launches and drivetrain longevity. The factory BMW transfer case bushings—especially on the G8X and F9X platforms—are notoriously soft. That’s the last thing you want when you’re putting serious power down.
Sure, you could replace the entire bushing with a solid one, but that often requires lowering or removing the transfer case—not to mention the added NVH (noise, vibration, and harshness) that comes with it.
Our transfer case bushing inserts offer a smarter solution: reduce bushing flex without sacrificing comfort. You keep smooth, quiet drivability around town and at idle—but when it’s time to launch, the transfer case stays planted.
Fitment Notice – Two Versions Available:
BMW uses two different transfer case bushing types. We now offer Version A and Version B inserts to match.
⚠️ You must physically inspect your vehicle’s bushing to determine which version you need.
We are not responsible for incorrect orders if this step is skipped. -
VTT is proud to offer a Titanium hardware upgrade for all our Billet and Cast VC's. This will come with M6x30 Ti bolts N54 /N55/S55/B58 Gen 1/ B58 TU it will be an Umbrella head with a 16.3mm head. These bolts weigh half as much as comparable steel hardware and look amazing. Colors to choose from will be Burnt, Black, and Natural (silver)
-
VTT is proud to offer Titanium wheel stud kits for the owner looking for the lowest possible unsprung weight while maintaining high strength, and good looks as all come with an amazing burnt finish. This kit is 60% lighter than factory steel studs and nuts with a total kit of 20 nuts, and studs being 3.1LBS. Sets of 10 are 1.55 lbs
-
Sale!Looking for a Lightweight, AFFORDABLE drag pack that looks amazing for your BMW, Toyota, or VAG platform? Look no further! VTT is proud to announce our lineup of Drag pack wheels for various BMW/Toyota/VAG fitments! We teamed up with Rota and had them open custom molds for us of their extremely popular Grid design. With these molds, we have an exclusive on 15X10, 17X10, and 17X4.5 wheels in our exact specs. The wheels are currently offered in the colors and sizes below
A variety of Offsets are available, as well as spacers here - VTT Spacers can be found here - https://vargasturbo.com/product/vtt-billet-wheel-spacers/
As well as Center bore adapters here - https://vargasturbo.com/product/vtt-billet-hubcentric-wheel-bore-adapters/Wheels are priced EACH, meaning per wheel
PLEASE NOTE! CHECK FITMENT CAREFULLY. ANY WHEELS THAT HAVE HAD TIRES MOUNTED OR ARE DAMAGED DURING TEST FITTING ETC ARE NOT RETURNABLE!
We make NO CLAIM these fit ANY PLATFORM, or ANY factory brake set up. It is YOUR JOB to measure, and make sure they will fit BEFORE you mount tires or install them. WE NEVER suggest shaving down brake calipers to fit a smaller wheel. If they do not fit. GET A SMALL BRAKE KIT!
Colors offered:- Satin Black
- Gloss Black
- Bronze,
- Gun Metallic
- 15x10 ET45/ET40 (wheel weight 16 lbs)
- 17x10 ET45/ET40/ET25 (wheel weight 19lbs)
- 17x4.5 ET-20 (wheel weight 16 lbs)
- 15x10 ET45 - (wheel weight 16 lbs)
- 17x10 ET45/ET40/ET25 (wheel weight 19 lbs)
- 17x4.5 ET-20 (wheel weight 16 lbs)
-
Looking to go above 45 psi in your BMW-powered vehicle? Looking for a plug-and-play solution? We have you covered with our BMW 5 bar sensor. These will allow 58 psi to be read and are factory plug-and-play. Simply remove your old sensor, replace it with the 5 bar, and have your tuner rescale your map values in both your DME tune and your PI tune if applicable.
These are GENUINE BMW sensors directly from BMW.
PLEASE NOTE: These are GENUINE BMW sensors directly from THE BMW DEALERSHIP, BMW IS PUTTING A BMW STICKER OVER A DENSO BOX, AND SELLING THEM. THESE DO NOT HAVE BMW STAMPS ON THEM. WE HAVE ZERO CONTROL OVER THIS.
-
VTT B58 “GC / GC-MID / GC+” Turbocharger Upgrades
Wheel Sizing / Power Support
Model Wheel Size (Comp/Turb) Stock Engine Power Range GC 54/55 Up to 600WHP GC-MID (TU ONLY) 54/60 Up to 650WHP GC+ 67/68 Up to 800WHP
Ready to take your B58 platform to the next level—without core charges, long waits, or compromising spool? VTT has you covered. Our 100% new casting B58 GC-Series turbochargers (GC, GC-MID, and GC+) retain the OE packaging advantages while removing the factory airflow limitations and weak internal architecture.
We start by keeping what BMW did right, then eliminate every bottleneck we found: the restrictive factory inlet, inefficient bearing housing oiling, small thrust assembly, and anything else holding the B58 back. Then we incorporate proprietary VTT improvements and cast everything at full OE-level quality.
The result? Serious B58 power made simple. GC turbos are direct bolt-on upgrades that retain all factory connections (oil, water, charge pipe, downpipe) while supporting 600WHP+ — with factory-like spool.
NOTE: The GC is Super Core ONLY, meaning no exhaust housing; this turbo plugs directly into your factory exhaust housing.
-
We are happy to release our BMWB58 (Fits ALL B58 models including TU found in the A90/A91 Toyota Supra) vacuum/boost adapter. These go inline with the intake manifold fitting and provide a full boost/vacuum signal from the manifold. This fitting adds two 1/8NPT bungs to accept any fitting that has 1/8" NPT threads. You can choose options, Fitting by itself, 1/4" barb, as well as 1/8NPT plugs if you only want one barb, etc. You can choose straight or 90-degree barbs. Once installed it tucks perfectly under your engine cover. These are perfect for running your PI switch off manifold pressure which is much more accurate than charge pipe, and they are also great for BOV running the proper size line without having to drill a hole in your manifold. These do space out any sensors etc giving inaccurate readings like some of the other brands do. They are made from 6061-T6 anodized black, with steel plugs, and Blue Anodized barbed fittings. You can choose to order in a few ways. Adapter alone - $40 Basic kit - 1 Adapter, 1 barb, and one plug $45.00 Dual Barb kit - 1 Adapter, 2 barbs, $55.00
-
This is for those running our brake kits that use our 11.75" or 13" Rotors that want to easily change between rotors for dedicated drag racing and street use. You can now buy Rotor/Hat Assemblies by themselves to switch between any of our 3 options
The price is for ONE ROTOR / OR ONE ROTOR/HAT ASSEMBLY
-
Looking to protect your single turbo investment, dont have a ton of room, and need a low profile filter that can flow what you need? VTT Has you covered with our Low Profile Single turbo Air Filters. These filters are custom-made for VTT. They are made with a heat-resistant silicone base, and a high-flowing cotton weave element with a pre-oiled design to catch contaminates but allow free flow. We currently offer them in Black, and 3 flange sizes. 3", 4" and 5" flange. With two filter heights. Tested at over 1200WHP with no loss of power observed. Filter Options - Offered in White, and Black with the following dimensions Short - 3.75" Tall, 7.5" OD Large end, 5" Small end 3", 4", or 5" Flange Tall - 4.5" Tall, 7.5" OD Large end, 5" Small end 3", 4", or 5" Flange
-
Looking to make sure all metal contaminates that are possibly in your oil are not circulated? VTT has you covered with our Titanium Magnetic oil drain plugs for BMW, and any other vehicle that uses an M12x1.5 drain plug. This drain plug will capture any ferrous metal particles in your oil, and capture them to be cleaned during your next oil change. It also is stronger than a Steel or Aluminum drain plug, and looks cool! These are made from GR5 Titanium and use a rare earth magnet to capture metal particles in your oil... Kit includes:
- 1 Titanium Drain Plug
- 1 M12 Crush Washer
-
VTT/PFS Stainless Steel Fuel Strainer for Walbro In-Tank Pumps
The fuel system is one of the most critical components of your entire build—it delivers the fuel that translates into big power and fast times! Without proper filtration, your Walbro 274, 285, or 295 fuel pump can ingest contaminants, leading to premature failure. However, choosing the right strainer or pre-filter is just as important as post-filtration. 🚨 Why Does Your Fuel Pump Need the Right Strainer? ✅ Too fine of a filter can restrict flow and cause the inlet to collapse. ✅ Too coarse of a filter can allow debris to pass through, damaging the pump and engine. ✅ Low-quality materials can break down, collapse, or cause fueling issues—leading to potential engine failure.The VTT/PFS Stainless Steel Fuel Strainer – The Ultimate Solution
-
Looking to adapt your wheel bore size to a smaller hub bore? VTT has you covered with our hub-centric adapters. These adapters are made from Billet 6061-T6 aluminum, and anodized in black. We have these sizes currently
- 57.1mm hub to 60.1mm wheel bore
- 57.1mm hub to 64.1mm wheel bore
- 57.1mm hub to 66.1mm wheel bore
- 57.1mm hub to 66.6mm wheel bore
- 57.1mm hub to 67.1mm wheel bore
- 57.1mm hub to 70.3mm wheel bore
- 57.1mm hub to 71.6mm wheel bore
- 57.1mm hub to 72.6mm wheel bore
- 57.1mm hub to 73mm wheel bore
- 57.1mm hub to 74mm wheel bore
- 57.1mm hub to 74.1mm wheel bore
- 64.1mm hub to 72.6mm wheel bore
- 66.6mm hub to 72.6mm wheel bore
They are sold in sets of two, order TWO SETS for a full car, or one set per axle.
-
Our studs are forged from cold-rolled 10.9-class steel and finished with a black oxide corrosion-resistant coating, ensuring years of dependable service in both street and motorsport environments.
We offer one optimized size: 85mm overall length, with the following breakdown:
-
75mm total thread length
-
10mm bull nose for smooth lug engagement
-
12mm short-thread section (hub side)
-
12mm unthreaded shank
-
48mm long-thread section (lug nut side)
These studs are coated using Black Oxide, which does protect, BUT even when using Black Oxide, the studs CAN develop surface rust if left to the elements. We suggest a slight coat of WD-40 when you clean your wheels to prevent this.
These studs are coated using Black Oxide, which does protect, BUT even when using Black Oxide, the studs CAN develop surface rust if left to the elements. We suggest a slight coat of WD-40 when you clean your wheels to prevent this.
-
-
Looking to convert your 5x112 M14x1.25 vehicle, such as A90/91 Toyota Supra, and 2020+ BMW G-series, to 5x114 to open up your wheel options? We got covered with our VTT wheel stud conversion kits. These kits are forged cold-rolled steel in 10.9 class, with Black Oxide corrosion-resistant coating for years of use, and convert your vehicle to M12x1.50 wheel studs, which allow you to fit 5x114 wheels with no other changes. No wobble bolts or redrilling here. Simply install the studs, put the wheel on, and the lug nuts will center the wheel. This kit is Black Studs with Black Lugnuts, and we offer it in 10 or 20 pieces if you want to only do the front/rear or both.
Our studs are forged from cold-rolled 10.9-class steel and finished with a black oxide corrosion-resistant coating, ensuring years of dependable service in both street and motorsport environments.
We offer one optimized size: 85mm overall length, with the following breakdown:
-
75mm total thread length
-
10mm bull nose for smooth lug engagement
-
12mm short-thread section (hub side)
-
12mm unthreaded shank
-
48mm long-thread section (lug nut side)
PLEASE NOTE – THESE STUDS WILL ONLY WORK IF YOUR WHEELS ARE DRILLED M14 THESE WILL NOT WORK FOR WHEELS DRILLED M12!
These studs are coated using Black Oxide, which does protect, BUT even when using Black Oxide, the studs CAN develop surface rust if left to the elements. We suggest a slight coat of WD-40 when you clean your wheels to prevent this.
DO NOT USE ANY HUB-CENTERING SLEEVES WITH THESE CONVERSION STUDS, THE LUGS WILL CENTER THE WHEELS. THE USE OF A CENTERING SLEEVE MAY LEAD TO STUDS BREAKING. FOR INSTALLATION YOU MUST SNUG EACH LUG UP SLOWLY, AND IN A STAR PATTERN TO GET THE WHEEL CENTERED ON THE LUGS, FAILURE TO DO SO CAN ALSO LEAD TO FAILURE.
-
-
Building a kit using Mac solenoids to control boost? Need an easy way to mount it? VTT-FAB has you covered with our billet Mac Solenoid brackets. Machined from 6061 billet and anodized in 3 colors, these are the perfect way to mount your Mac valve and look good while doing it. Each kit includes:
- One Mac Solenoid bracket (3-Port or 4-Port)
- 2 Allen screws to hold the valve to the bracket
- M6 Mounting Bolt
-
Racing can be rough on brake pads, if you have worn through a set of pads while using your VTT brake kit you can buy replacement pads here. Different options are available as shown below. Please take a look at your pads to see the hole orientation which will determine your pad type BP-10 pads for Dynalite calipers Single hole in the pads for the location pin - Mostly street and some racing we recommend for rear kits BP-20 pads for Dynalite calipers Single hole in the pads for the location pin - More aggressive street driving, and racing recommended for front or rear kits BP-10 pads for Dynapro calipers with twin holes in the pads for the location pins - Mostly street and some racing we recommend for rear kits BP-20 pads for Dynapro calipers with twin holes in the pads for the location pins - More aggressive street driving, and racing are recommended for front or rear kits Hawk PC (Performance Ceramic) Very Quiet, Very low dust, Hawk claims 32% increase in stopping power over stock pads. A good balance of street, and aggressive driving. Recommended for front or rear kits
MANY MORE AGGRESSIVE BRAKE PAD COMPOUNDS EXIST FROM VARIOUS MANUFACTURERS, AND YOU CAN TAILOR TO YOUR NEEDS. Y OU CAN FIND THESE BY USING THE CALIPERS STYLE NUMBERS BELOW.
6-PISTON DYNAPRO PAD STYLE 6712
4-PISTON DYNAPRO PAD STYLE 7812
-
Looking to remove your BOV either for leak testing, or dont want to run one, and your charge pipe or housing has a flange on it. You can use this billet plate to block off the BOV flange. Uses the O-ring from the BOV to seal, and removes the BOV. Fitment: Tial BOV Turbosmart BOV with female flange like Tial
-
Need a Tee fitting for plumbing Vacuum, or Boost lines, Don't want to use cheap plastic ones that can get soft when hard, and brittle after they heat cycle? We didn't either, which is why we machined these high-quality billet tees to solve this issue. Machine from 6061-T6 aluminum, and anodized in black for a long-lasting corrosion-free finish, these tees look great, and will you never have to worry about one failing. We offer them in two sizes, each size has 12mm legs and 3 barbs:
- 7.60mm / -4 Push Lock for people looking to use -4 push lock hose or -4 AN hose. This is a perfect fit for those.
- 1/4" For people looking to use 1/4" vacuum tube
-
Need to work on the B58 engine outside of the car? Lift it to put on an engine stand etc? BMW makes an engine lifting tab but it costs $25, and they do not always have them in stock. We made our own, to avoid the high cost, and possibly long wait time. The perfect tool when you want to lift the engine balanced in the place BMW designed for it to be lifted. Made out of coated steel for high strength, long life, and corrosion resistance. Fits all B58 models, and possibly S58
-
Tired of your Dragy flying all over the car as you try to do runs? Tired of low sats or no sats warning due to improper location of the Dragy in the vehicle? Well say goodbye to those issues with our new Carbon Fiber and Plastic Dragy holders. These are made from either 100% Pre-Preg Carbon Fiber, or molded plastic for a perfect fit. The carbon fiber gives it just the right look to add to your performance vehicle! Each holder has dual Suction cups and will stick to any smooth surface. We suggest mounting them in the upper left or right corner of your windshield with a full view of the sky. Dragy holder features
- Stop your Dragy from flying off the dash, and having to search for it
- Position your Dragy in the optimal position for the best satellite coverage
- VTT Dragy holder exposes the entire top of the Dragy so nothing is blocking the receiver from the Satellite
- The charging port is not blocked and can be accessed with the cover on
- Choose from REAL Carbon Fiber or Molded Plastic
-
VTT is happy to offer our very unique and universal billet mount to fit any roll bar or cage with 1.5", 1.75", or 2" diameter tubing. These mounts are designed from 6061-T6 aluminum and are made to SECURELY hold a JBL Flip version 3 - Version 6 and allows you to bring music into your race car, off-road vehicle, rock crawler, boat, basically anything that has a length of tubing this will allow you to have an easy way to have tunes without having to install and mount a stereo system. They can also be used as a single mount to hold things such as a helmet, steering wheel, or anything you want to quickly hang for easy access once seated. For the JBL flip you will need TWO mounts, simply install them loosely, snap in your JBL Flip to get the proper spacing, and tighten down. The device is then securely mounted and can be removed easily. We offer these in a variety of anodized colors for a long-lasting durable finish including Black, Red, Blue, Clear, Orange, and Green Mounts are sold individually Features:
- Billet 6061-T6 Aluminum construction anodized in a variety of colors
- Can be used to SECURELY mount a JBL Flip 3-6 to anything that has a length of 1.5", 1.75" or 2" tubing
- Can also be used as a universal mount for anything you need to hang in your race car, off-road vehicle, etc
- Completely reversible, and can be moved from vehicle to vehicle
-
VTT B58/S58 Head Port Block-Off / Built Check Valve Kit
The VTT B58/S58 Head Port Block-Off / Check Valve Kit is designed to either seal off or convert the factory head ports used by the OEM low-side PCV system. These ports in the cylinder head utilize engine vacuum to evacuate crankcase gases — but in the process, can allow oil to enter the intake manifold, leading to valve carbon buildup and other performance issues over time.
This kit provides two configuration options:
-
Block-Off Version – Completely seals the factory head ports to prevent oil intrusion and unwanted vacuum leaks.
-
Billet Check Valve Version – Converts the head ports into a robust internal PCV system using precision-engineered check valves. These one-way valves allow vacuum to function as intended while blocking boost pressure from entering the crankcase or charge tract.
By bypassing the factory PCV valve in the valve cover, the VTT kit replaces it with an improved three-valve internal system integrated directly into the cylinder head. This design improves reliability, simplifies plumbing, and ensures consistent crankcase pressure management — critical for both stock and high-performance B58/S58 applications. This kit does NOT require any tapping, meaning no metal to get into the engine etc. You simply tap the plugs or check valves into place.
Key Features
-
Eliminates oil draw-through into the intake manifold
-
Prevents carbon buildup on intake valves
-
Converts to an internal, head-integrated PCV system
-
Utilizes precision-machined check valves for boost sealing
-
Fully reversible — Block-offs or valves can be removed if needed
- No tapping is required. Easy install, by tapping the blocks or valve into place.
-
-
VTT is proud to introduce our billet replacement for the BMW B58 factory plastic oil filter housing cap.
The OEM plastic cap is a known weak point that can crack or deform under heat and pressure. Our billet solution not only eliminates that failure risk, but also integrates a high-strength magnet to capture fine metallic particles from your oil — adding an extra layer of engine protection.
Key Features
-
Direct OEM Replacement – Retains all factory provisions for the filter basket, including the critical lower pins that ensure proper oil pressure bypass function.
-
Added Protection – Built-in magnet continuously pulls metal particles from your oil, helping maintain a cleaner lubrication system.
-
Premium Construction – CNC-machined from 6061-T6 aluminum for superior durability.
-
Anodized Finish – Available in four colors for corrosion resistance and engine bay style.
-
Complete Compatibility – Designed specifically for the BMW B58 platform.
Available Colors
-
Red
-
Black
-
Blue
-
Clear
-
-
Looking to up your boost limit on just about any BMW vehicle that runs a 3 or 4-wire BMW map sensor including but not limited to S58, B58, N54, N55, S55, S63, B48, B47, B42, B57, B46? We were too, so we decided to make a very easy plug-and-play kit for 3, and 4-wire BMW map sensors. These kits will allow you to completely replace the 3-wire sensor with one of our sensors, leave your stock 4-wire in place for IAT sensing, and move the power, ground, and sensor signal from the factory sensor to our sensor. These sensors have the proper scaling which will allow your tuner to simply change your map sensor scaling in the tune, and the factory ECU will be able to utilize the sensor voltage with no problem. We are offering these in 5 bar (58 psi), and 6 bar (72 psi), and each comes with a plug-and-play harness, and optional fittings for ease of installation.
Note: For the S58/B58 our Factory style Pre-Throttle map sensor is also 5 bar, and will work fine coupled with the post throttle kit, but the scaling is different, if you want matching Voltages Pre/Post throttle you can run two of these.
A variety of install pics can be found below and - Here
Scaling PDF Links: 5-Bar / 6-Bar
Features include:- Plug and Play harnesses with no wire splicing
- Output wire for connecting a PI or external controller to your post-throttle map sensor for the most stable signal that is not affected by throttle closure
- Different fittings are available for your plumbing needs.
- Can have matching voltage signals for pre/post throttle for ease of tuning, and boost reference
- B58/S58 etc Pre Throttle - 3 Wire Harness (Charge pipe to 1/8" NPT adapter needed, for B58/S58 90 degree adapter needed to provide sensor clearance)
- B58/S58 Post Throttle - 4 Wire Harness (Boost reference will be needed from manifold to sensor)
- F90 M5 Pre/Post Throttle - 4 Wire Harness (May need to repin) (Boost reference will be needed from manifold to sensor)
- Most all other platforms Pre/Post Throttle - 4 Wire Harness (May need to repin) (Boost reference will be needed from manifold to sensor)
- B58
- S58
- S63/ S63TU
- N63
- N54
- S55
- N55
- N20
- B46
- B48
- B57
- B47
-
VTT noticed a hole in the VTT A9X Supra/BMW Z4 / G2X / G42 Billet Diff Lock Down Kit market for a high-quality, lightweight, NVH-friendly, and easy-to-install Diff Lock Down kit to improve diff stability under launching, and hard cornering. So we did something about it and went to work on a very innovative design that 100% positively locks the diff down from movement, while shielding it from adding a ton of NVH, and can be used with the stock diff, and subframe bushings. This design uses existing mounting points on the vehicle, you do NOT have to remove the subframe or the Diff to install. Simply remove 4 diff bolts, drill two holes in the subframe slightly bigger, install two M10 riv-nuts, and install the lockdown, you do not even have to move the exhaust. A typical install can be 15-30 minutes for someone who is experienced working on vehicles, an hour if you like taking it slow. You WILL need a Riv-nut tool to install the Riv-nuts, we provide a link below for what we recommend on Amazon. Features:
- Lightweight 1.5 lbs for the entire lockdown plate
- Uses FOUR connection points on the Diff, and two on the subframe for the ultimate in positive diff location, this will stop all diff movement on launch, saving your guibos, etc
- 100% Billet construction from 6061-T6 aluminum
- Anodized in 4 colors for corrosion resistance, a long-lasting finish, and good looks
- The subframe does NOT have to be removed for installation
- Uses all 12.9 grade hardware
- Does not add excessive NVH
- Positively locks down the diff to eliminate all unwanted movement under launches, acceleration, cornering, etc.
All products that are designed to stiffen or reduce drivetrain movement inherently have the tendency to increase NVH or Noise, Harness, or vibration. While these bushings inserts have been found to add little NVH in most instances. Your results and sensitivity to NVH may vary. This product is designed to reduce drivetrain movement, and that was the goal when designing and manufacturing this product. Returns for NVH are not accepted once products are installed.
-
Need to move your coolant expansion tank to the other side of the vehicle for a single turbo kit you are building, extend Map sensor plugs, or IAT, how about Throttle Body? Don't cut your factory wires. Just get a VTT-FAB extension harness, and plug and play! These come in various lengths and are covered in expanded sheathing with heat shrink on both ends for a long-lasting, good-looking finish. Available:
- Coolant Extension for late model BMW 2015+ 5 ft
- Pre-Throttle Map sensor extension harness 2 ft
- Pre-Throttle IAT Sensor extension harness 2 ft
- B58/S58/B48 etc Throttle body extension harness 2 ft
- B58 to S55 Throttle conversion/extension harness 2 ft
- EWG Actuator Extension harness, Various Lengths
- N54 stock MAP to N20 Map sensor extension
-
VTT is proud to announce our A90/91 Supra engine catch can set up. This kit uses our already extremely popular modular catch can, and couples it with a custom CNC 6061 bracket, VTT CNC banjo fittings, VTT 5 ply silicone hose, and Push lock fittings. Install is simple, takes about 30 minutes to 2 hours depending on your skill level, and requires removing one factory hose to install the VTT hoses. Giving an OEM fit and finished when installed This catch can fits all known intake variations we have seen, including stock intake. Kit Break down is as follows:
- One Catch Can
- One CNC 6061 bracket
- Two -10 Low Profile CNC Banjo Fittings
- Two -10 VTT 5-Ply silicone Vacuum hoses
- Two -10 Push Lock Fittings
- Two spring clamps
- Available with an optional Drain fitting, allowing quick draining
-
Looking for Mac solenoids for your build? We got em here at VTT-FAB so you can get everything in one place. We have 3-port, and 4-port in stock!
-
VTT is proud to offer a truly plug-and-play line lock kit for select BMW vehicles that does NOT require running wiring inside the car, mounted switches, holes in the dash, etc. Our newly designed and released line lock kits use a 40amp wireless remote control switch with 4 different modes that allow you to tailor your line lock setup exactly as you prefer. You simply install the solenoids, install the harness with the switch which has all the wiring terminated, bleed the brakes, and you are ready for effortless burnouts which will not be interfered with by the DME because you are holding the brakes, nor wear your rear brake pads. You can store the remote anywhere in your vehicle, center console, cup holder, door cup holder, etc., and when you need to do a burnout to heat your race tires it's in arm's reach without running any wiring into the vehicle. Fitment is confirmed for G8X M3/4, A9X Supra - The kit itself including lines, solenoids, etc will fit most all late model BMW Chassis including F8X, F3X, G2X, etc. The main concern will be mounting the wireless switch in the passenger cowl area. The kit includes:
- Line lock solenoids with weather pack connectors
- Two Parker 90-degree -3 an fittings
- Two Stainless Steel adapter fittings
- Two DOT Approved Stainless Steel brake lines
- One complete wiring harness
- One Remote control switch with TWO remotes
-
VTT Billet Aluminum Valve Cover – B58 TU
The Only Billet Valve Cover Option for the B58 TU Platform
VTT is proud to introduce our B58 TU Billet Aluminum Valve Cover, designed for enthusiasts looking to enhance both the performance and appearance of their engine bay.
The OEM plastic valve cover is known to crack over time and contains a problematic built-in PCV system. Our billet cover eliminates those issues and gives you complete modularity and control over your PCV setup.
We recommend pairing it with our B58 TU Catch Can Kit for the ultimate crankcase ventilation solution. Additional breather options—including our oil cap breather and one-way stainless breathers—are also available to further enhance your setup.
Key Features
-
100% CNC-machined 6061-T6 aircraft-grade aluminum
-
Anodized in a variety of durable color options
-
Lightweight at 9.7 lbs (vs. 7.9 lbs for the stock plastic cover)
-
Includes three shrouded -10 ORB ports for maximum PCV flexibility
-
Fully baffled ports to reduce oil carryover
-
Only billet option currently available for the B58 TU
-
Optional titanium hardware or OEM-style fasteners
-
-
The Factory B58 TU water neck is plastic and is right in the path of your charge pipe if you lose a connection and it blows off. If this does happen to you it can break the plastic neck emptying your coolant in seconds causing you in the best-case scenario to be stranded, and in the worst-case scenario expensive engine damage. Add some cheap insurance with our Billet Water neck.
-
Improve engine/shifting feel without a huge increase in NVH or high cost! VTT A9X billet motor mount inserts upgrade mounts the way BMW does it, allowing a minimal increase in NVH while stiffening up the engine/shifting feel, and getting rid of excessive engine movement
-
VTT Billet & Forged Carbon Strut Bar – A90/A91 Toyota Supra
Building on the success of our Billet G8X Strut Bars, VTT has now engineered a version specifically for the A90/A91 Toyota Supra. This design is a true evolution — not a metal bar wrapped with carbon overlay, but a genuine forged carbon fiber center section paired with precision-machined billet ends.
Each end is CNC-machined from either 6061-T6 aluminum or Grade 2 Titanium, ensuring exceptional strength, rigidity, and long-term durability. Every piece is finished in-house and anodized in your choice of Black, Red, Blue, or genuine T2 Titanium rainbow finish.
This is a true performance and visual upgrade — not just an accent piece.
Key Features
-
Real Forged Carbon Fiber Construction – No metal core or cosmetic overlay; this is a full forged carbon center section.
-
Billet Aluminum or Titanium Ends – CNC-machined from 6061-T6 aluminum or T2 Titanium for maximum precision and strength.
-
Premium Finishes – Choose from Black, Red, Blue anodized, or genuine T2 Titanium rainbow finish.
-
Direct Fit Design – Installs using factory mounting points; designed for a perfect fit on the A90/A91 Supra.
-
-
Want to tighten up the diff on your 2021+ G8X M3/M4, A9X Supra, G42 2 Series, or G2X BMW and help eliminate any extra diff movement on hard launches? We got you covered with our Rear Billet diff insert kit. This is pressed into the factory bushing and fills the voids in the bushing. This keeps the stock bushing ride compliance but removes any unwanted movement. These are sold as a kit. To install remove the rear diff bushing, use the stock bolt in press the bushing in, and then replace it with the new bolt washer, and lock nut! Kit includes:
- One Billet Bushing insert
- Two 46mm Hardened Steel Washers
- One 12.9 M14 Bolt
- One M14 Lock nut
THIS KIT MAY REQUIRE LOWERING OF THE SUBFRAME TO GET THE STOCK BOLT OUT, AND THE NEW ONE IN
All products that are designed to stiffen or reduce drivetrain movement inherently have the tendency to increase NVH or Noise, Harness, or vibration. While these bushings inserts have been found to add little NVH in most instances. Your results and sensitivity to NVH may vary. This product is designed to reduce drivetrain movement, and that was the goal when designing and manufacturing this product. Returns for NVH are not accepted once products are installed.DOES NOT INCLUDE DIFF BUSHING IN PHOTO!
-
Unsure of the state of your CHRA's, whether brand new from a questionable source or rebuilt? Don't install them without having a proper High-Speed balance done! This is the #1 most critical factor when building a turbocharger, and is even more important for performance turbochargers or small twins that see a LOT of RPM. We use a Turbo Technics VS3 balancer, and balance most units down to under .5G Not all turbos will be able to pass a high-speed balancing test for any number of reasons (usually poor assembly, bent shaft, etc), if they will not pass, we will send you the specs they are in, and as close as we could get them. We then will give you the option to send them back, or we can disassemble, and rebuild them in-house using our other balancing, and assembly tools to ensure a properly built/balanced unit. The service is for most turbos, and we have the capability to balance most units, NOT ALL. If sending in twins please choose TWO as the quantity
UNITS MUST BE SENT IN WITH NO HOUSINGS, AND IN A CONDITION READY TO BE BALANCED, IF YOU NEED TO SEND IN COMPLETE TURBOS, WE CAN DISASSEMBLE, AND BALANCE FOR YOU, BUT AN EXTRA CHARGE WILL APPLY. IF THE UNITS ARE SENT IN A CONDITION WHERE THEY CAN NOT BE BALANCED WE WILL LET YOU KNOW THE PRICE TO GET THEM TO A STATE WHERE THEY CAN BE
-
VTT “GC” Rear Drag Brake Kit
A90 / A91 Toyota Supra
Looking to make your A90/A91 Supra quicker in the 1/4-mile or 1/2-mile?
Want to run 17” or even 15” rear wheels with only minor suspension modification?
Want to drop up to 35 lbs of unsprung weight from the rear of the car — without breaking the bank?
The VTT “GC” Rear Drag Kit is designed specifically for straight-line performance. This kit allows you to run the wheel and tire combination you need to lower ETs while significantly reducing rotational and unsprung mass compared to the factory rear brake setup.
Less weight.
More clearance.
Better weight transfer.
Faster passes.
Fitment
-
2020+ Toyota Supra A90/A91 (B58 platform)
-
Confirmed fitment on many BMW G-Series chassis, including G20, G42, and others.
(Contact us to confirm your specific chassis.)
Notes
-
Minor suspension modification may be required for certain wheel/tire combinations.
-
Photos shown are for reference only.
-
Hardware, brackets, and mounting configurations may vary by platform.
-
-
Low Profile socket for installing, and removing the vanon central valve bolt on BMW/Mini/Rolls Royce, and some For vehicles. This tool give you the space to get a TQ wrench in between the engine and the firewall to properly tighten the vanos central valve bolt.
- Removes later style central valve on BMW Vanos Hubs and Ford VCT
- Services BMW B38, B48, B58, MINI Vanos, and Ford VCT modules
- 22mm x 16 Points
- 1/2" Square Drive
- Chrome molybdenum with black phosphate finish. Compare to Ford Factory Tool 303-1661-3 and BMW Factory Tool 2-450-487
-
VTT Cone Filters feature High flow elements with a silicone body and a velocity stack built-in for smooth flow. We offer these filters in a variety of sizes for universal use. These are also replacement filters for VTT intake kits including B58 Gen 1, TU, Supra, Audi 4.0, N54 Dual Cone filter kit, etc Kit Includes:
- 1 - Cone Filter
- 1 - Clamp
-
Tired of getting off the dyno, and having your drivetrain malfunction light on due to a broken plastic ride height bracket? So were we, after we broke 3 of them, we knew it was time to make our own to combat the issue. This bracket is cut from 6061-T6 for strength and anodized black for a long-lasting finish.
-
VTT Billet Velocity Stack (V-Stack)
3" • 4" • 5" Inlet Sizes
Running an open turbo and want to straighten airflow into the compressor for maximum efficiency? The VTT Billet Velocity Stack is exactly what you need.
Backed by fluid-dynamics principles, a proper bellmouth / velocity stack smooths incoming airflow, reduces turbulence, and improves air entry into the turbocharger—or intake on naturally aspirated applications. Unlike thin, stamped alternatives, our V-Stacks are precision-machined for strength, consistency, and performance.
Each unit is CNC-machined from 6061-T6 billet aluminum and anodized for durability and corrosion resistance. Available in 3", 4", and 5" inlet sizes, these stacks are designed to fit any intake tubing or turbocharger inlet of the corresponding diameter.
-
Do you work on a lot of BMW engines from various platforms? Do you ever struggle with heavy cylinder heads, either lifting off the engine or simply moving around? Ever ruined an EXPENSIVE multi-layer head gasket while trying to install a cylinder head due to no secure way to hold it without two people? We answered yes to all of those things, and came up with a tool for anyone that works on BMWs often, and needs a way to simply, and easily remove/install, or simply move around a cylinder head. These cylinder head tools are machined from a solid billet of 6061-T6 aluminum and anodized in 4 colors for long-lasting corrosion resistance. They are knurled for a non-slip grip when oily or wet, and positioned so the head is balanced when lifting The Head Handler fits the following engines, N54, N55, S55, B58, S58 and we offer short extensions for installation with no cams/Cam ledges on the head, or long extensions for people that want to install or remove a head with cams still installed. (B58 only requires short extensions)
-
Show off your VTT support and get a good laugh from people with our "We Like To Party" License plate bracket. Born from the infamous quote in Talladega nights
-
We have a variety of fittings in stock to help you get your turbo system plumbed up! Available are:
- 1/8" NPT to -6 AN Male (Great for water lines, or anywhere you need a small 1/8" NPT to -6 Male AN)
- M14x1.5 to -6 AN Male (Great for water lines on Garrett turbos GT, GTX, and G-Series, or anything that has a metric M14x1.5 thread and you need a -6AN male)
- .035" Turbo feed restrictors. These are for Garrett turbochargers and will fit GT, GTX, and G- Series up to G35
- Garret GT, GTX, and G-Series up to G35 -8 An drain adapter. For those that want a low profile -8 drain for their GT-G-Series Garrett. (Comes with two bolts, and a gasket)
-
VTT Modular Silicone/Billet Intake System – Toyota A90/91 Supra (B58TU Engine)
VTT is proud to announce our Modular Silicone/Billet Intake System for the A90/91 Toyota Supra with the B58TU engine.
After countless hours of testing and fitting, we’ve engineered an intake that delivers both optimized airflow and OEM-level fitment.
Why Upgrade?
The factory Supra airbox is efficient, but the intake tract to the turbo is a problem area. It’s full of twists, turns, and accordion bellows that disrupt airflow, plus a built-in silencer that restricts performance by bypassing air simply to quiet intake sound.
By replacing these with our 3"–3.5" free-flowing silicone intake tube, paired with your choice of:
-
The stock airbox (for factory sound/appearance),
-
Our 6" cone filter with built-in velocity stack (for maximum airflow and sound), or
-
Our Carbon Fiber Airbox Lid with high-flow panel filter,
…you remove restrictions and create a smooth, optimized air path straight to the turbo.
Our testing shows that the stock airbox supports up to ~700WHP. Beyond that, we recommend upgrading to the 6" cone system for maximum efficiency.
-
-
PFS is proud to offer a true drop-in 800-1000WHP+ capable LPFP for A90/91 Toyota Supras. This LPFP needs NO additional pumps, wiring harnesses, etc etc. It will support up to 800WHP on Ethanol percentages as high as E98 and will support much higher power levels with less E content as long as you have the octane to support it. For the pump, we start with a factory bucket, we modify it extensively to accept our custom PFS Brushless fuel pump. We then re-terminate the factory wiring to accept the new pump. No wiring splices, done the same way the factory does -the right way.
-
VTT Billet Oil Cap – BMW S58 & B58TU
Ditch the factory plastic and upgrade to a true performance piece. The VTT Billet Oil Cap is CNC-machined from solid 6061-T6 aluminum and anodized in your choice of vibrant finishes. Unlike snap-on covers, this is a complete replacement cap engineered for strength, precision, and long-term reliability.
-
Premium Materials – 6061-T6 aircraft-grade aluminum with precision machining.
-
Functional Design – Direct replacement for the OEM cap with proper sealing and durability.
-
Anodized Finishes – Available in five colors to match or contrast your build.
-
High-End Look – Adds a clean, motorsport-inspired aesthetic to your engine bay.
Fitment
Designed specifically for all BMW S58 and B58TU G-Series engines, including (but not limited to):-
G8X M3 / M4
-
Toyota A9X Supra
-
All G-Series 2, 3, 4, 5, 7, 8, and X models
A simple upgrade that delivers both style and substance—because your BMW deserves more than plastic.
-
-
The Factory B58 TU Upper Cylinder head hose is plastic and is right in the path of your charge pipe if you lose a connection and it blows off. If this does happen to you it can break the plastic neck emptying your coolant in seconds causing you in the best-case scenario to be stranded, and in the worst-case scenario expensive engine damage. Add some cheap insurance with our Billet Upper Cylinder head hose, this sits right above the plastic water neck. Product Details:
- Plug and play direct factory replacement
- 6061-T6 Billet aluminum with black anodizing for a corrosion-free life
- 7-Ply Silicone in 3 colors
- Cheap insurance against a blown charge pipe which could turn into a blown motor
-
Want to tighten up the diff on your A9X Supra, G42 2 series, or G2X BMW and help eliminate any extra diff movement on hard launches or cornering? We got you covered with our Billet diff inserts. They are machined from 6061-T6, and anodized black for a long-lasting finish. They install easily by removing the diff bolts one at a time, lowering the diff slightly, inserting the bushing, and installing new washers, and bolts. Kit includes:
- 2 Front inserts
- 2 Rear inserts
- 2 Hardened 46mm washers
- 2 110mm M12x1.5 Bolts
All products that are designed to stiffen or reduce drivetrain movement inherently have the tendency to increase NVH or Noise, Harness, or vibration. While these bushings inserts have been found to add little NVH in most instances. Your results and sensitivity to NVH may vary. This product is designed to reduce drivetrain movement, and that was the goal when designing and manufacturing this product. Returns for NVH are not accepted once products are installed.
-
High-Boost Crankcase Ventilation Adapter for BMW Engines Building or running a high-boost, high-powered BMW engine? Boost increases crankcase pressure, which, if left unchecked, can lead to issues such as smoking, power loss, and even engine failure. Adequate venting is essential for optimal performance and engine health. These are designed to connect directly to S58/B58(TU) stock VC, or screw into ANY VTT Billet or Cast VC While some believe a -10AN vent is sufficient for these builds, the truth is: it’s not. To address this, we developed a larger, more effective solution for our builds—now available for everyone. Our Oil Cap adapter securely snaps in place, replacing your oil cap and providing a platform for a -16ORB fitting in a variety of configurations. Choose from -12AN to -20AN fittings, depending on your build’s needs. This cap is thicker than our low-profile option so care must be taken when planning hood clearance for the versatile venting options.
Key Features:
- Attractive Oil cap design
- Connects to stock S58/B58(TU) VC or VTT Billet/Cast VC
- Vented, comes with multi-hole venting to knock down large oil droplets before they make their way into the catch can system
- High-performance venting: Supports configurations from -12AN to -20AN fittings.
- Customizable: Compatible with various fittings to suit your build.
Important Notes:
- This kit requires you to supply your own hose, hose ends, and catch can to complete the system.
- Some fitting options may require 4–5 days for shipping, as we keep only select configurations in stock.
- Also fits other platforms such as B48, B46, Mini, etc. DOES NOT FIT Gen 1 B58
-
Looking to convert your G90/G99 M5’s 5×132 bolt pattern to more common 5×112 or 5×114.3 wheels and open up your wheel options dramatically? We’ve got you covered with our VTT wheel spacer conversion kits.
These kits are CNC-machined from billet 6061-T6 aluminum and anodized for a long-lasting finish. We press in class 10.9 studs with a corrosion-resistant zinc coating for years of reliable use.
Each spacer allows you to bolt on either 5x112 or 5x114.3 wheels while maintaining proper hub-centric fitment. No wobble bolts or redrilling required.
Options & Specs:
-
Available in 15mm, 17.5mm, and 20mm thicknesses
-
Hub bore: 66.6mm (Hub-centric adapter rings available for other sizes)
-
Studs: M14x1.5
-
Stud length: 40mm total
-
Includes black open-ended 19mm lug nuts
QTY 1 is for ONE SPACER. If you need to do 4 wheels order FOUR!
We offer Hub-Centric adapter rings to fit other wheel bore sizes
-
-
VTT is proud to offer our Billet Aluminum ZF8HP Transmission Pan – the ultimate upgrade over the factory plastic or cast aluminum pans.
CNC-machined from 6061-T6 aluminum and anodized in multiple colors, this pan adds durability, serviceability, and performance benefits. With 2 extra quarts of fluid capacity, built-in cooling features, and premium sealing, it’s designed for both daily drivers and high-performance builds.
Key Features
-
6061-T6 Billet Construction – Stronger, longer-lasting, and precision-machined.
-
Increased Fluid Capacity – 5.7 QTs (5450ML) vs. the stock 3.7 QTs (3500ML).
-
Improved Cooling – Machined external fins aid heat dissipation.
-
Integrated Magnet – Rare-earth magnet supports the filter while pulling metal debris from the fluid.
-
Premium Seal – Reusable US-made Viton gasket for a leak-free seal.
-
Easy Service – -6 ORB magnetic drain plug for quick, clean fluid changes.
-
Anodized Finish – Corrosion-resistant and available in multiple colors.
-
-
Out of stockVTT Is proud to offer a seamless Chromoly Driveshaft for the A90/91 Supra. This driveshaft is made from seamless 4130 Chromoly steel and forged 4130 weld ends, and Spicer 1350 Yolks, and U-Joints. All pieces are then precision tig welded, and balanced. We couple the driveshaft with VTT Custom 7075 aluminum adapters which convert the 3 bolt BMW bolt pattern to the 4 bolt Spicer yolk patter. This driveshaft is rated at 4100 ft/lbs of Tq, and more than 10,000RPM.
-
Looking for some more fuel for your B58 powered BMW? Not looking to break the bank on overpriced PI kits? PFS has you covered with its Plug, and play PI kit for the B58.
-
VTT is proud to offer the PFS A90/91 Supra upgraded LPFP line. This line replaces the factory line from the tank to the hard-line under the drivers feet with a line which increases diameter 22%, and volume/area 56% over factory line. The factory line is just under 8mm ID the PFS line uses genuine Parker 801-6 hose which is 10mm ID. This is a plug-and-play option. Remove your factory line, and install this line in its place, it will fit in all the line holders.
-
High-Boost Crankcase Ventilation Adapter for S58/B58 Engines Building or running a high-boost, high-powered S58 or B58 engine? Boost increases crankcase pressure, which, if left unchecked, can lead to issues such as smoking, power loss, and even engine failure. Adequate venting is essential for optimal performance and engine health. While some believe a -10AN vent is sufficient for these builds, the truth is: it’s not. To address this, we developed a larger, more effective solution for our builds—now available for everyone. Our low-profile adapter securely snaps in place, replacing your oil cap and providing a platform for a -16ORB fitting in a variety of configurations. Choose from -12AN to -20AN fittings, depending on your build’s needs. At just 10mm thick, this adapter maximizes hood clearance for versatile venting options.
Key Features:
- Low-profile design: Only 10mm thick for maximum hood clearance.
- High-performance venting: Supports configurations from -12AN to -20AN fittings.
- Customizable: Compatible with various fittings to suit your build.
Important Notes:
- This kit requires you to supply your own hose, hose ends, and catch can to complete the system.
- Some fitting options may require 4–5 days for shipping, as we keep only select configurations in stock.
- Also fits other platforms such as B48, B46, Mini, etc. DOES NOT FIT Gen 1 B58
-
VTT is proud to offer our EWG "Direct Control System" or DCS! This is a completely new innovation for people looking to control the highest-flowing wastegate on the market using an existing BMW electronic actuator. This system will allow BMW owners who have a vehicle with Electronic Wastegates from the factory to utilize this system to control an externally wastegated turbo system, AND it will ALSO allow ANY vehicle to use this setup to control your own custom turbo system. This is done by utilizing our custom 7075 Billet aluminum bracket coupled with a Turbosmart Straight gate, and if needed an EWG controller made for us by DCCD Pro. This allows direct external wastegate control over any turbocharger system with or without EWG for the factory. Features:
- Utilizes the most current wastegate technology the Turbosmart Straight Gate. This gate allows maximum flow with minimal restriction, low drive pressure, and much more. Full details can be found here - https://www.turbosmart.com/product/electronic-straightgate-esg50-external-wastegate/
- Can be configured in multiple ways, and angles based on how you mount the adapter
- The adapter is 7075 Aluminum which has the strength of steel and weight of aluminum
- All connection fittings, are made from Nitronic 60 which has extremely high temperature and wear properties
- Zero Drive Pressure, no springs, no poppet valves, direct control over the gate using factory ECU logic
- Adaptable to ANY turbo system on any car to provide the ultimate in boost control!
-
Introducing the VTT Remote Oil Cooler Plate for BMW B58 Engines Need extra oil cooling for your track-oriented B58 build or simply looking for better cooling capacity in high-temperature climates? If so, you’re likely considering running an external or upgraded oil cooler on your BMW B58-powered vehicle. However, BMW’s design doesn’t make this easy—the heat exchanger is built directly into the oil filter housing. That’s where the VTT Remote Oil Cooler Plate comes in. This innovative solution allows you to easily and conveniently remove the factory coolant-supplied heat exchanger on the oil filter housing and replace it with -10AN or -8AN fittings, simplifying the process of running your oil cooler lines. No need to worry about looping the coolant—our plate features a built-in housing that seamlessly loops the coolant circuit for a hassle-free installation.
Key Features:
- Convenient Oil Cooler Integration: Add a remote oil cooler to your BMW-powered vehicle (Gen 1 and Gen 2 B58 engines).
- Flexible Plumbing Options: Includes -8AN or -10AN fittings for easy line routing.
- Built-In Coolant Loop: Eliminates the need to manually loop the coolant circuit, simplifying installation.
- Direct Plug-and-Play Replacement: No modifications or retrofitting required.
- Optional Fittings Available: Choose with or without fittings based on your setup.
What’s Included:
- One Block-Off Plate with Coolant Loop Housing
- Six M6 Bolts
- Optional -10AN or -8AN Fittings
- Optional Factory Gaskets
-
Looking to replace your damaged factory BMW Actuator part number - 11658691853 VTT has located and ordered in bulk these actuators, and offer them at a discounted price. These are 100% FACTORY BMW OEM actuators, not aftermarket. Fitment is for the following, but they work to replace basically any BMW Actuator.
-
VTT is proud to offer a Phenolic spacer for the BMW B58 platform. When upgrading to an aluminum charge cooler you get the benefit of a better core, and more cooling capacity, but it also comes with the downside of DIRECT heat transfer from the head to the manifold which can cause heat soak and less-than-ideal IAT's even with an upgraded charge cooler. We manufacture these from G11 Expoxy sheet which has great heat and hardness characteristics, and we feel is the ideal material for this application. The thickness is 8mm.
Please note: Longer studs or bolts may be required introducing a phenolic spacer into your system
-
Sale!Get the COMPLETE lockdown kit for your A9X / G2X / G42 at one low price. Order all 4 pieces together, and save 5%! Transfer Case Bushing are optional
-
THE DRIVESHAFT for the MK5 Supra!
Why overpay for a carbon fiber MK5 Supra driveshaft?
VTT is proud to offer a premium carbon fiber driveshaft manufactured exclusively for VTT in the USA by GCDS (Gulf Coast Driveshaft) — one of the premier driveshaft manufacturers in the country with extensive experience in high-performance and drag racing applications.
Each driveshaft is constructed using 3.25" carbon fiber tubing, paired with NEAPCO Performance 1350 series U-joints, then bonded using a proprietary high-strength process and precision balanced to within 1/8 in-oz as a complete assembly.
Every shaft is torque tested in-house prior to shipping to ensure proper bonding and structural integrity. GCDS and VTT are among the few manufacturers that perform full torque testing on each shaft before it leaves the facility.
To complete the system, the driveshaft is paired with VTT-designed 7075 aluminum adapters, eliminating the factory guibos and unnecessary flex points. The shaft connects directly to the BMW 3-bolt front flange, while a VTT 4340 rear adapter replaces the factory slip-in / screw-retained shaft design for improved strength and reliability.
Proudly Made in the USA.
PLEASE NOTE! Driveshafts can have UNUSUALLY LONG LEAD TIMES. We hope to reduce this with GCDS, but if the shaft shows OUT OF STOCK, expect a lead time of 4–8 weeks, unless we specifically state that it can ship sooner.
Due to the nature of these shafts being manufactured by a 3rd party, ANY ORDERS PLACED FOR VTT CF DRIVESHAFTS ARE 100% FINAL.
NO REFUNDS. NO CANCELLATIONS. FOR ANY REASON.
THIS INCLUDES LONG LEAD TIMES.
PLEASE ORDER CAREFULLY. ONCE THE ORDER IS PLACED, IT IS FINAL.
-
VTT “GC” Front Drag Kit – A90/91 Toyota Supra / G Series BMW
Looking to make your A90/91 Supra faster in the ¼ mile or ½ mile? Want to run 17” wheels (or even 15” with suspension modifications) and front skinnies? How about shedding nearly 70 lbs of unsprung weight from the front of the car — without breaking the bank?
Look no further than the VTT “GC” Front Drag Kit. This kit is designed specifically for drag racing, giving you the wheel/tire setup you need to drop ETs while putting your Supra on a serious diet compared to the heavy OEM front brakes.
Pictures are for REFERENCE ONLY. All kits will come with varying hardware, brackets, and mounting styles based on the platform.
-
BMW damper bolts are grade 10, and Torque to Yield, meaning one-time use. This is fine for factory power levels, but when turning things up. These bolts leave a lot to be desired. We have seen damper bolts come loose, and break causing engine and crank damage, we have seen improper TQ load between bolts. The factory bolts are just not up to snuff if you plan to run above factory power levels. We are proud to offer a solution with genuine ARP 8740 Chromoly replacements at a budget-friendly price. These bolts are made in the USA to ARP's exacting standards meaning you know each bolt is going to do what it was designed to do, and that is provided even, repeatable TQ load. Each kit contains:
- 4 VTT/ARP 4340 Chromoly Damper Bolts
- Thread Size: M10 x 1.5
- Fastener Head Style: 12-point
- Fastener Material: Chromoly
- Fastener Color: Black
- Fastener Grade: ARP 8740 chrome moly
- Fastener Tensile Strength (psi): 180,000+ psi
- Wrench Diameter: 12mm
-
Please Note: This is a Virtual Gift Card. After purchase you will receive an email with your Gift Card code
-
Glass in your VTT Catch Can broken? If so we have replacements avaialble for $10 each. These are direct replacements for the glass that came with your cans.
-
Product Release: VTT Billet Installation Dowels
Ever tried wrestling a BMW transfer case into a car on your own? Or struggled to line up a transmission or subframe as you're sliding it into place? If you have, you know just how tedious—and downright frustrating—it can be.
After doing these installs hundreds of times, we used to rely on cut-off factory bolts to help guide components into place. But cutting bolts for different applications turned out to be a hassle—time-consuming, inconsistent, and often not long enough to provide the guidance needed.
So we created a better solution: VTT Billet Aluminum Installation Dowels—designed specifically to make these installations easier, faster, and more accurate.
Key Features:
-
One universal length: 6 inches
- Bull nose for easy slip into the part being installed
-
Two thread sizes
-
Three thread pitches
-
Built-in 5mm hex in the end for easy install and removal
Available Thread Options:
-
M10 Standard Pitch – Ideal for BMW transfer case installs and more
-
M12 x 1.5 Fine Thread – Perfect for most BMW front and rear subframe installations
-
M12 Standard Pitch – Designed for BMW transmission installs
-
-
These are the same premium pistons we use in our winning race and high-performance street engines around the world! We feel that these are the best pistons for your high performance or racing engine.
-
Secure Your AN Fittings the Right Way – Without the Damage
VTT now offers a complete line of precision Billet 6061-T6 Aluminum AN Wrenches, designed to grip without marring your fittings. Whether you're working with -3 or -20 AN sizes, we've got you covered.These wrenches are lightweight, durable, and anodized in 8 vibrant colors for a long-lasting finish and easy size identification.
Available Options:
-
Full Kit: Includes all sizes from -3 to -20
-
Common Size Kit: Includes -4, -6, -8, -10, and -12
-
Individual Wrenches: Purchase only the sizes you need
-
-
Looking to maximize your A90/91 for drag racing? Want to be able to dial in the perfect amount of compression or rebound on your launch? The VTT Double adjust drag shock kit is just want the doctor ordered!
-
VTT -16 Billet HIGH-FLOW Catch Can System
Maximum Venting for Maximum Power
VTT is proud to introduce our -16 Billet High-Flow Catch Can System — designed from the ground up for high-horsepower applications requiring serious crankcase ventilation. Whether you're pushing over 900WHP or beyond 2000WHP, this system delivers unmatched performance, reliability, and engine bay cleanliness.
Key Features:
-
Supports -16 AN lines (with optional -12 or -20 fittings)
- 20 Fluid OZ capacity
-
Engineered for big-power builds needing high crankcase pressure relief
-
Triple-stage filtration system to eliminate oil mist — even in the event of engine failure
-
Designed, tested, and proven to keep oil inside the catch can — not in your engine bay
Triple Filtration Technology:
-
Stage 1 - Stainless steel filter – captures 95% of oil mist on entry
-
Stage 2 - Perforated diffuser plate – further disperses and slows down airflow
-
Stage 3 - Final stainless mesh layer – scrubs out any remaining vapor before venting
This advanced system has been tested with over 200 PSI of pressure and more than half a quart of oil without releasing a trace of oil mist. As long as the catch can is properly serviced and not overfilled, even catastrophic engine failure won’t result in a mess under your hood.
Application-Specific Kits Available:
We offer plug-and-play kits for popular platforms, including:
-
G8X M2/M3/M4 (S58) SINGLE TURBO ONLY
-
F9X X3M/X4M SINGLE SINGLE TURBO ONLY
-
A9X Toyota Supra
Each Plug and play kit includes everything needed for installation: catch can, vehicle-specific bracket, fittings, hoses, and optional drain. Again, plug-and-play kits include ALL required parts. Bracket, fittings, line, etc. No additional fittings are required except the drain if wanted.
-
-
Looking for a head gasket for your BMW that will hold ALL of the boost? So were we, and nothing we tried worked. So we took matters into our own hands and had what we wanted made. These gaskets are made out of carbon material, and use stainless steel fire rings to ensure you are not pushing boost into your water jacket or between cylinders. There are two versions:
- One does NOT require a groove to be cut into the block
- One DOES require a groove to be machined into the block to accept the fire ring.
- Custom made to our specs from Carbon material that will form your head/deck, and seal oil/water passages while fire rings, keep boost in the combustion chamber
- FULLY tested in-house on multiple builds to ensure boost level can be achieved
- They are NOT like the other fire ring gaskets on the marker (SCE/Athena) that do not require machine work, we had zero luck with those. THESE FLAT OUT WORK!
- Choose non-machined or machined version
- Different thicknesses are available as a custom order (4-8 week lead time)
- Different Bores Available as a custom order (4-8 week lead time)
For any gaskets NOT in stock expect a 4-8 week lead time as these are custom-made for us. This includes ANY gasket we currently do not have in stock.
-
VTT is proud to offer 2020+ Toyota Supra Carbon fiber intake lids. BMW did a wonderful job designing these intakes and we have found they are only slightly restrictive at elevated power levels. With this in mind, we decided to just take their cues, and make a factory-style carbon fiber intake top with a high-flow cotton pre-oiled filter. These are 8 layers of 100% carbon, not a single layer wrapped over plastic, and they are 1.3MM thick with our logo vacuum printed onto the tops, with a UV-resistant gloss clear coating. This is not only strong but will resist discoloration for an extended period of time. The filters themselves are made with a heat-resistant silicone base, a high-flowing cotton weave element with a pre-oiled design to catch contaminates but allow free flow. Filters are available by themselves for a flow upgrade while keeping the stock look here – https://vargasturbo.com/product/vtt-bmw-toyota-b58-tu-high-performance-drop-in-air-filter-upgrade/ Complete CF Lid kit with Silicone intake tube, and billet adapter available here - https://vargasturbo.com/product/vtt-a90-91-supra-modular-silicone-intake-system/
-
VTT is proud to offer high-performance drop-in replacement filters for the BMW B58 TU, this includes G series BMW including Z4, A90/91 Toyota Suora, and. These filters are custom-made for VTT. They are made with a heat-resistant silicone base, and a high-flowing cotton weave element with a pre-oiled design to catch contaminates but allow free flow. We designed these to work with our Carbon Fiber intake Tops, but these filters will also work perfectly with the stock tops. We offer them in two colors. Red, and Black Features:
- 50 States Emissions Legal
- Easy to install in 15-30 minutes even for a novice
- Filters can be cleaned forever meaning never buy new filters
- Completely reversible if you ever want to remove
-
VTT Caliper Upgrade Package
4-Piston to 6-Piston Conversion
Designed for customers currently running VTT brake kits equipped with our 4-piston calipers who want the ability to upgrade for increased stopping power.
This package allows you to easily switch between 4-piston and 6-piston caliper configurations without purchasing a complete brake kit again.
-
Carrillo connecting rods are well known within pro racing and street performance circles for good reason; they produce a premium product that winning racers around the world depend on.
-
Sale!
VTT B58/S58 HPFP Block-Off Plate Kit
If you’re converting your B58 or S58 build to port injection (PI) only and removing the direct injection (DI) system and high-pressure fuel pumps (HPFPs), you’ll need to properly seal the HPFP ports in the valve cover.
Our billet aluminum block-off plates provide a simple, clean solution.
Just remove the HPFP and cam follower, then install the plate — it seals the valve cover and eliminates the HPFP cleanly and securely.Please Note:
-
Removing the HPFP typically requires a standalone ECU.
-
If you’re only removing a single HPFP (such as on the S58), a tune adjustment will be necessary for proper operation.
-
-
PFS Stage Cheap DIY Fuel Pump Upgrade Kit (plus limited Pre-Built units available)
Need more fueling headroom but don’t want to drop big money on a full upgrade? The Stage Cheap DIY kit is exactly what it sounds like — an affordable, effective way to boost your low-pressure fuel pump performance without adding wiring, controllers, or complexity.
This kit repurposes high-quality OEM-based components into a high-flow solution for the A90/A91 Toyota Supra and BMW G-Series platforms (excluding M3/M4 and X3M/X4M).
Key Features:
-
✅ ~50% more flow than a stock LPFP
-
✅ Once assembled, kit is 100% plug-and-play
-
✅ No additional wiring or external controllers required
-
✅ Retains full factory fit and function
-
✅ Ideal for pump gas or E85 builds
-
✅ Built from OEM-quality components
-
✅ A perfect entry-level fueling upgrade
-
-
VTT is proud to be an authorized reseller of Race Tech Seats. These are the premiere seats for your drag build or road race car. See Specs/Features below
-
VTT is proud to be an authorized reseller of Race Tech Seats. These are the premiere seats for your drag build or road race car. See Specs/Features below
-
VTT is proud to offer PTE Turbocharger products! Please Note: All Precision Turbos have a 2-3 week shipping time
-
VTT is proud to be an authorized reseller of Race Tech Seats. These are the premiere seats for your drag build or road race car. See Specs/Features below
-
VTT-FAB B58 Factory Control EWG Top Mount Single Turbo kit
For BMW G-Series & Toyota A91 6-Port B58 Platforms
VTT-FAB is proud to offer the premiere top-mount single turbo system for the BMW G-Series and Toyota A91 B58 platforms. This kit is 100% made in the USA at our Hayward, CA facility, using only the highest-quality materials and components.
At the core is a hand-fabricated equal-length 321 stainless steel manifold with billet flanges, designed for maximum flow, durability, and that signature 6-into-1 turbo sound. The system is paired with our factory-controlled external wastegate setup, featuring a Turbosmart 60mm Straight Gate. This innovative design allows full external gate control through the OEM ECU — no additional boxes, MAC solenoids, or vacuum/boost lines required. Simply reuse your factory actuator with our adapter for seamless, plug-and-play control from 0 PSI all the way up to your turbo’s limits.
Unlike other kits, the VTT-FAB system uses no silicone couplers. Instead, we provide VTT-FAB HD clamps to eliminate the risk of blown boost hoses under extreme load.
⚠️ Important Notes:
-
Every VTT-FAB kit is built to order and cannot be canceled once fabrication begins. Please order carefully.
-
If your kit of choice is listed out of stock, email [email protected] for current build times.
-
Garrett turbo options are oil-cooled only (no water lines). This is perfectly fine for street and drag applications. For extended track/road-race use, we recommend adding water cooling
-
-
Sale!
VTT x PFS EBS (External Brushless System) Fuel System
VTT, in collaboration with Performance Fueling Solutions (PFS), is proud to introduce the PFS EBS — External Brushless System.
The EBS is a fully stand-alone, next-generation brushless fuel system available in both platform-specific and universal fitments. Built around state-of-the-art Protec brushless pump technology, this system is capable of supporting up to 2,500 HP on ethanol-based fuels — and even more on gasoline or ethanol blends.
With its compact 15" x 10" footprint and ultra-lightweight construction, the PFS EBS is engineered for performance without compromise. The complete system — including pumps, surge tank, FPR, controllers, and wiring harness — weighs in at under 10 lbs (dry), thanks to a carbon fiber mounting plate and carefully chosen lightweight materials.
EBS Bench Testing Video:
EBS Bench Test Video -
Give the Gift of VTT! Looking to get your friends, or family some go-fast parts, and no idea what they need, only that they love VTT? Well, our Gift Cards have you covered! They come in $50, $100, $250, $500, and $1000 increments. Each gift card is precision cut out of plastic in the shape of the VTT logo and has the dollar amount and the code on the back. Each gift code is unique and is locked to that card. To redeem simply enter the code during check out it will remove that amount, and if you have any leftover it will go back to the card.
You can choose to have your card physically mailed to you, or a virtual card where we can send you a scan of your card.
-
VTT Is proud to offer the BC stroker kit for the Toyota B58B30 engine platform that incorporates a 100mm stroke, steel billet crank, BC 4340 Pro Series Heavy-Duty connecting rods rated to 1600+ horsepower.
