-
Introducing the VTT OBD-LOCK – Enhanced Security & Improved Design!
We are excited to announce our OBD-LOCK! This latest version has been completely redesigned for improved strength, ease of installation, and enhanced protection. Key upgrades include:
No more OBD port penetration – eliminates any risk of damage
Revised thread style – prevents stripping for a secure fit
Stronger, more durable design – ensures maximum securityUltimate OBD Port Protection
The VTT OBD-LOCK is precision-machined from billet 6061-T6 aluminum and is engineered to completely lock out your OBD port, preventing unauthorized access.
Anti-Theft Protection – Prevents thieves from accessing the OBD port to duplicate keys or disable security systems
Dealer/Tech Lockout – Stops unauthorized tune changes or system modifications
Tamper-Proof Design – Cannot be removed without physically destroying the OBD port unless the correct tool is usedVTT OBD-LOCK – Version 2 NON-GM
Universal Fit for All Non-GM (General Motors) VehiclesThis device is compatible with all non-GM vehicles, including but not limited to:
-
All VAG group vehicles (VW, Audi, Bentley, etc.) — including recessed port VW/Audi models
-
Ford, Nissan, Honda, Toyota, Porsche, Dodge, Ram, Jeep, Kia, Subaru, and more
Not compatible with GM (General Motors) vehicles.
VTT OBD-LOCK – Version 2 GM
Universal Fit for GM (General Motors) Vehicles ONLYThis version is specifically designed for General Motors vehicles, including GM, Chevrolet, Cadillac, Holden, and other GM-branded models.
If your vehicle is anything other than a General Motors product, you will need the Non-GM version.
-
-
VTT Head Port Block-Off Kit
The VTT Head Port Block-Off Kit is designed to seal the built-in ports in the cylinder head that utilize engine vacuum to clear the low-side PCV system. This factory setup can draw oil into the intake manifold, leading to valve carbon buildup and other unwanted issues.
Kit Includes:
-
6 precision-fit set screws
-
Engine-specific tap
This kit is compatible with N54 engines. Each kit is supplied with the correct tap for your specific engine type.
-
-
Please note: Due to heavy increases in freight costs we have had to raise prices by $50 on 54-gallon drums, and $15 on pails.
VTT is proud to be the West Coast dealer for One Ethanol racing fuel.
We have two blends available in 5-gallon pails and 54-gallon drums. See below for descriptions of both fuels
Fuel is available for local pick up only unless you email, and make arrangements for freight shipping. Be aware fuel is considered hazmat and the freight charges are equal to or more than the fuel in all instances. Fuel CANNOT be shipped normal shipping methods such as UPS, FED EX, etc
-
VTT/PFS Stainless Steel Fuel Strainer for Walbro In-Tank Pumps
The fuel system is one of the most critical components of your entire build—it delivers the fuel that translates into big power and fast times! Without proper filtration, your Walbro 274, 285, or 295 fuel pump can ingest contaminants, leading to premature failure. However, choosing the right strainer or pre-filter is just as important as post-filtration. 🚨 Why Does Your Fuel Pump Need the Right Strainer? ✅ Too fine of a filter can restrict flow and cause the inlet to collapse. ✅ Too coarse of a filter can allow debris to pass through, damaging the pump and engine. ✅ Low-quality materials can break down, collapse, or cause fueling issues—leading to potential engine failure.The VTT/PFS Stainless Steel Fuel Strainer – The Ultimate Solution
-
Looking to get rid of the troublesome and expensive DI injectors on your BMW N54 and move to PI only and a standalone? If so VTT has you covered with its new N54 PI delete kit. This kit allows you to SAFELY remove the DI injectors, install our delete fittings, and run PI only. We machined these deletes from 310 Stainless for extreme heat, and corrosion resistance, and include 3 hold downs. These DI deletes COMPLETELY get rid of all factory provisions, including the seal. If the seal is left intact with no fuel to cool the injector or delete it will quickly overheat and melt the delicate seal causing combustion gasses to escape the engine creating misfires, and worse possibly damaging your injector bore on the cylinder head. Our deletes are machined to be a press fit into the cylinder, and can be either cooled with liquid nitrogen, and dropped in, or tapped in with a hammer, and then held down with the included hold downs. We also include M6 tapped holes on the top of each one in case they need to be removed you can attach a slide hammer, and remove the delete. These are sold as a kit and come with the following
- 6 - 310 Stainless DI Delete fittings
- 3 - Hold down brackets
EXTREME ENGINE MODS ARE REQUIRED TO RUN THIS KIT, PLEASE SEE BELOW
-
Looking to remove the HPFP or DI system on your N54? This plate will block the vacuum pump and prevent oil leaks. You will need to remove any fuel lines, etc. Kit includes
- Block Plate
-
Need a Tee fitting for plumbing Vacuum, or Boost lines, Don't want to use cheap plastic ones that can get soft when hard, and brittle after they heat cycle? We didn't either, which is why we machined these high-quality billet tees to solve this issue. Machine from 6061-T6 aluminum, and anodized in black for a long-lasting corrosion-free finish, these tees look great, and will you never have to worry about one failing. We offer them in two sizes, each size has 12mm legs and 3 barbs:
- 7.60mm / -4 Push Lock for people looking to use -4 push lock hose or -4 AN hose. This is a perfect fit for those.
- 1/4" For people looking to use 1/4" vacuum tube
-
Looking to up your boost limit on just about any BMW vehicle that runs a 3 or 4-wire BMW map sensor including but not limited to S58, B58, N54, N55, S55, S63, B48, B47, B42, B57, B46? We were too, so we decided to make a very easy plug-and-play kit for 3, and 4-wire BMW map sensors. These kits will allow you to completely replace the 3-wire sensor with one of our sensors, leave your stock 4-wire in place for IAT sensing, and move the power, ground, and sensor signal from the factory sensor to our sensor. These sensors have the proper scaling which will allow your tuner to simply change your map sensor scaling in the tune, and the factory ECU will be able to utilize the sensor voltage with no problem. We are offering these in 5 bar (58 psi), and 6 bar (72 psi), and each comes with a plug-and-play harness, and optional fittings for ease of installation.
Note: For the S58/B58 our Factory style Pre-Throttle map sensor is also 5 bar, and will work fine coupled with the post throttle kit, but the scaling is different, if you want matching Voltages Pre/Post throttle you can run two of these.
A variety of install pics can be found below and - Here
Scaling PDF Links: 5-Bar / 6-Bar
Features include:- Plug and Play harnesses with no wire splicing
- Output wire for connecting a PI or external controller to your post-throttle map sensor for the most stable signal that is not affected by throttle closure
- Different fittings are available for your plumbing needs.
- Can have matching voltage signals for pre/post throttle for ease of tuning, and boost reference
- B58/S58 etc Pre Throttle - 3 Wire Harness (Charge pipe to 1/8" NPT adapter needed, for B58/S58 90 degree adapter needed to provide sensor clearance)
- B58/S58 Post Throttle - 4 Wire Harness (Boost reference will be needed from manifold to sensor)
- F90 M5 Pre/Post Throttle - 4 Wire Harness (May need to repin) (Boost reference will be needed from manifold to sensor)
- Most all other platforms Pre/Post Throttle - 4 Wire Harness (May need to repin) (Boost reference will be needed from manifold to sensor)
- B58
- S58
- S63/ S63TU
- N63
- N54
- S55
- N55
- N20
- B46
- B48
- B57
- B47
-
VTT N54 Billet Center Feed Intake Manifold
VTT is proud to introduce our ground-up engineered N54 Billet Center Feed Intake Manifold—not a rebadged sheet metal clone like others on the market. This is a purpose-built manifold designed for performance, utility, and seamless integration.
Through advanced CAE/Multiphysics simulations under both steady and unsteady state conditions, we’ve delivered a manifold that not only outflows the OEM unit but also installs with zero compromises. No need for custom charge pipes or modified throttle body harnesses—bolt it on and go.
Real-world testing on a 570WHP stock-motor F-RB Lite turbo car yielded 20–30WHP gains with no tuning changes, especially at the top of the RPM range—where it counts most. Expect even greater results with ported heads, high-lift cams, or higher-output builds.
-
The PFS POD (Planetary OverDrive) is an Overspeed gearbox for your N54/early N55 high-pressure fuel pump. Mechanical fuel pump flow potential is a function of shaft speed -spin it faster, get more fuel flow. The PFS POD allows the user to increase the shaft speed 3x, drastically increasing the output capability of a stock N54 HPFP, and avoid the issues of implementing Port Injection and/or Methanol Injection on vehicles that are targeting more power than the stock fuel system can supply.
-
Adding a Front-facing manifold to your N54, and need to extend your map sensor harness? We got you covered with our 24" extension harness. High-quality wiring, with seating, and our own 3D printed connectors ensure a perfect fit. Fits all N54, and very early N55, please check your plug connection on your map sensor before ordering
-
Glass in your VTT Catch Can broken? If so we have replacements avaialble for $10 each. These are direct replacements for the glass that came with your cans.
-
Sale!
VTT x PFS EBS (External Brushless System) Fuel System
VTT, in collaboration with Performance Fueling Solutions (PFS), is proud to introduce the PFS EBS — External Brushless System.
The EBS is a fully stand-alone, next-generation brushless fuel system available in both platform-specific and universal fitments. Built around state-of-the-art Protec brushless pump technology, this system is capable of supporting up to 2,500 HP on ethanol-based fuels — and even more on gasoline or ethanol blends.
With its compact 15" x 10" footprint and ultra-lightweight construction, the PFS EBS is engineered for performance without compromise. The complete system — including pumps, surge tank, FPR, controllers, and wiring harness — weighs in at under 10 lbs (dry), thanks to a carbon fiber mounting plate and carefully chosen lightweight materials.
EBS Bench Testing Video:
EBS Bench Test Video
