-
VTT-FAB Carbon Fiber Turbo Blanket
$64.99 – $99.00Looking to keep the underhood heat down on your single turbo car, or build? We got you covered with our VTT-FAB Carbon Fiber Turbo Blankets. The outer shell is made of Carbon Fiber, and the inner shell is Silica Fiber. For 2500F intermittent / 1800 direct heat rating. We have them in 2 sizes T3, and T4. See fitment below Kit included:- 1 Carbon Blanket of choice
- 2 install springs
-
Sale!
VTT N54 Waste Gate Repair Kit / Rattle Fix
$109.99$89.99This kit comes with 1 set (both turbos) of Stainless Steel wear matched bushing, and flapper assembly, Wastegate arm, rod end, and Stainless steel 8mm C clip. -
Unsure of the state of your CHRA's, whether brand new from a questionable source or rebuilt? DON'T install them without having a proper High-Speed balance done! This is the #1 most critical factor when building a turbocharger, and is even more important for performance turbochargers or small twins that see a LOT of RPM. We use a Turbo Technics VS3 balancer, and balance most units down to under .5G Not all turbos will be able to pass a high-speed balancing test for any number of reasons (usually poor assembly, bent shaft, etc), if they will not pass, we will send you the specs they are in, and as close as we could get them. We then will give you the option to send them back, or we can disassemble, and rebuild them in-house using our other balancing, and assembly tools to ensure a properly built/balanced unit. The service is $79.99 each for most turbos, and we have the capabilities to balance most units. If sending in twins please choose TWO as the quantity
UNITS MUST BE SENT IN WITH NO HOUSINGS, AND IN A CONDITION READY TO BE BALANCED, IF YOU NEED TO SEND IN COMPLETE TURBOS, WE CAN DISASSEMBLE, AND BALANCE FOR YOU, BUT AN EXTRA CHARGE WILL APPLY. IF THE UNITS ARE SENT IN A CONDITION WHERE THEY CAN NOT BE BALANCED WE WILL LET YOU KNOW THE PRICE TO GET THEM TO A STATE WHERE THEY CAN BE
-
VTT Billet N54/N55 Vacuum/Boost Adapter
$49.99 – $64.99We are happy to release our BMW B54/N55 (Limited N55 Fitment) vacuum/boost adapter. These go inline with the Throttle Body fitting and provide a full boost/vacuum signal from the manifold. This fitting adds two 1/8NPT bungs to accept any fitting that has 1/8" NPT threads. You can choose options, 1/4" barb, as well as 1/8NPT plugs if you only want one barb, etc. These are perfect for running your PI off manifold pressure which is much more accurate than charge pipe, and they are also great for BOV running the proper size line without having to drill a hole in your manifold. These do space out any sensors etc giving inaccurate readings like some of the other brands do. They are made from 6061-T6 anodized black, with steel plugs, and Blue Anodized barbed fittings. You can choose to order in a few ways. You can choose straight or 90-degree barbs. Adapter alone - $40 Basic kit - 1 Adapter, 1 barb, and one plug, one vacuum cap, and one zip tie $45.00 Dual Barb kit - 1 Adapter, 2 barbs, one vacuum cap, and one zip tie $55.00 -
Looking to protect your single turbo investment, dont have a ton of room, and need a low profile filter that can flow what you need? VTT Has you covered with our Low Profile Single turbo Air Filters. These filters are custom-made for VTT. They are made with a heat-resistant silicone base, and a high-flowing cotton weave element with a pre-oiled design to catch contaminates but allow free flow. We currently offer them in Black, and 3 flange sizes. 3", 4" and 5" flange. With two filter heights. Tested at over 1200WHP with no loss of power observed. Filter Options - Offered in White, and Black with the following dimensions Short - 3.75" Tall, 7.5" OD Large end, 5" Small end 3", 4", or 5" Flange Tall - 4.5" Tall, 7.5" OD Large end, 5" Small end 3", 4", or 5" Flange
-
VTT-FAB Billet Mac Solenoid brackets
$45.99 – $49.99Building a kit using Mac solenoids to control boost? Need an easy way to mount it? VTT-FAB has you covered with our billet Mac Solenoid brackets. Machined from 6061 billet and anodized in 3 colors, these are the perfect way to mount your Mac valve and look good while doing it. Each kit includes:- One Mac Solenoid bracket (3-Port or 4-Port)
- 2 Allen screws to hold the valve to the bracket
- M6 Mounting Bolt
-
VTT Cone Filters
$39.99 – $49.99VTT Cone Filters feature High flow elements with a silicone body and a velocity stack built-in for smooth flow. We offer these filters in a variety of sizes for universal use. These are also replacement filters for VTT intake kits including B58 Gen 1, TU, Supra, Audi 4.0, N54 Dual Cone filter kit, etc Kit Includes:- 1 - Cone Filter
- 1 - Clamp
-
Sale!
Black Tial BOV Spring
$54.99$49.99If running a Tial BOV on your N54 instead of the TurboSmart Raceport you want to run the black spring. This will provide you with the most complete vent, and eliminate any chance for flutter/surge. -
Sale!
VTT Billet Check Valves
$24.99 – $29.99VTT CNC Billet check valve that can be used for a variety of uses including a vacuum/boost check valve when removing the stock PCV system, and still wanting to run vacuum to the crankcase. Rated at over 100 psi, with a cracking psi of .25psi.
