-
Looking to replace your damaged factory BMW Actuator part number - 11658691853 VTT has located and ordered in bulk these actuators, and offer them at a discounted price. These are 100% FACTORY BMW OEM actuators, not aftermarket. Fitment is for the following, but they work to replace basically any BMW Actuator.
-
Unsure of the state of your CHRA's, whether brand new from a questionable source or rebuilt? Don't install them without having a proper High-Speed balance done! This is the #1 most critical factor when building a turbocharger, and is even more important for performance turbochargers or small twins that see a LOT of RPM. We use a Turbo Technics VS3 balancer, and balance most units down to under .5G Not all turbos will be able to pass a high-speed balancing test for any number of reasons (usually poor assembly, bent shaft, etc), if they will not pass, we will send you the specs they are in, and as close as we could get them. We then will give you the option to send them back, or we can disassemble, and rebuild them in-house using our other balancing, and assembly tools to ensure a properly built/balanced unit. The service is for most turbos, and we have the capability to balance most units, NOT ALL. If sending in twins please choose TWO as the quantity
UNITS MUST BE SENT IN WITH NO HOUSINGS, AND IN A CONDITION READY TO BE BALANCED, IF YOU NEED TO SEND IN COMPLETE TURBOS, WE CAN DISASSEMBLE, AND BALANCE FOR YOU, BUT AN EXTRA CHARGE WILL APPLY. IF THE UNITS ARE SENT IN A CONDITION WHERE THEY CAN NOT BE BALANCED WE WILL LET YOU KNOW THE PRICE TO GET THEM TO A STATE WHERE THEY CAN BE
-
WHP Level supported (with proper fuel, upgrades, and tuning) Stock - 350WHP Our VTT N20 Stage 1 upgrade consists of a brand new N20 turbo, custom cast and manufactured for VTT, this is coupled with a VTT custom reverse billet 9-blade compressor wheel, and a brand new 9-blade high-flowing turbine wheel. Turbo upgrade is a complete bolt-on with no changes to water or oil lines and is undetectable by the dealership.
-
NGK 95706 Spark plug set required for running 100% e85, and high boost on many BMW applications, including N54, N55, S55, etc. Plugs can be bought as a set of 6. You can add pre-gapping for an additional charge
-
Introducing the VTT OBD-LOCK – Enhanced Security & Improved Design!
We are excited to announce our OBD-LOCK! This latest version has been completely redesigned for improved strength, ease of installation, and enhanced protection. Key upgrades include:
No more OBD port penetration – eliminates any risk of damage
Revised thread style – prevents stripping for a secure fit
Stronger, more durable design – ensures maximum securityUltimate OBD Port Protection
The VTT OBD-LOCK is precision-machined from billet 6061-T6 aluminum and is engineered to completely lock out your OBD port, preventing unauthorized access.
Anti-Theft Protection – Prevents thieves from accessing the OBD port to duplicate keys or disable security systems
Dealer/Tech Lockout – Stops unauthorized tune changes or system modifications
Tamper-Proof Design – Cannot be removed without physically destroying the OBD port unless the correct tool is usedVTT OBD-LOCK – Version 2 NON-GM
Universal Fit for All Non-GM (General Motors) VehiclesThis device is compatible with all non-GM vehicles, including but not limited to:
-
All VAG group vehicles (VW, Audi, Bentley, etc.) — including recessed port VW/Audi models
-
Ford, Nissan, Honda, Toyota, Porsche, Dodge, Ram, Jeep, Kia, Subaru, and more
Not compatible with GM (General Motors) vehicles.
VTT OBD-LOCK – Version 2 GM
Universal Fit for GM (General Motors) Vehicles ONLYThis version is specifically designed for General Motors vehicles, including GM, Chevrolet, Cadillac, Holden, and other GM-branded models.
If your vehicle is anything other than a General Motors product, you will need the Non-GM version.
-
-
Show off your VTT support and get a good laugh from people with our "We Like To Party" License plate bracket. Born from the infamous quote in Talladega nights
-
Looking to protect your single turbo investment, dont have a ton of room, and need a low profile filter that can flow what you need? VTT Has you covered with our Low Profile Single turbo Air Filters. These filters are custom-made for VTT. They are made with a heat-resistant silicone base, and a high-flowing cotton weave element with a pre-oiled design to catch contaminates but allow free flow. We currently offer them in Black, and 3 flange sizes. 3", 4" and 5" flange. With two filter heights. Tested at over 1200WHP with no loss of power observed. Filter Options - Offered in White, and Black with the following dimensions Short - 3.75" Tall, 7.5" OD Large end, 5" Small end 3", 4", or 5" Flange Tall - 4.5" Tall, 7.5" OD Large end, 5" Small end 3", 4", or 5" Flange
-
Sale!Looking for a Lightweight, AFFORDABLE drag pack that looks amazing for your BMW, Toyota, or VAG platform? Look no further! VTT is proud to announce our lineup of Drag pack wheels for various BMW/Toyota/VAG fitments! We teamed up with Rota and had them open custom molds for us of their extremely popular Grid design. With these molds, we have an exclusive on 15X10, 17X10, and 17X4.5 wheels in our exact specs. The wheels are currently offered in the colors and sizes below
A variety of Offsets are available, as well as spacers here - VTT Spacers can be found here - https://vargasturbo.com/product/vtt-billet-wheel-spacers/
As well as Center bore adapters here - https://vargasturbo.com/product/vtt-billet-hubcentric-wheel-bore-adapters/Wheels are priced EACH, meaning per wheel
PLEASE NOTE! CHECK FITMENT CAREFULLY. ANY WHEELS THAT HAVE HAD TIRES MOUNTED OR ARE DAMAGED DURING TEST FITTING ETC ARE NOT RETURNABLE!
We make NO CLAIM these fit ANY PLATFORM, or ANY factory brake set up. It is YOUR JOB to measure, and make sure they will fit BEFORE you mount tires or install them. WE NEVER suggest shaving down brake calipers to fit a smaller wheel. If they do not fit. GET A SMALL BRAKE KIT!
Colors offered:- Satin Black
- Gloss Black
- Bronze,
- Gun Metallic
- 15x10 ET45/ET40 (wheel weight 16 lbs)
- 17x10 ET45/ET40/ET25 (wheel weight 19lbs)
- 17x4.5 ET-20 (wheel weight 16 lbs)
- 15x10 ET45 - (wheel weight 16 lbs)
- 17x10 ET45/ET40/ET25 (wheel weight 19 lbs)
- 17x4.5 ET-20 (wheel weight 16 lbs)
-
VTT BMW Billet One-Way Crankcase Breather
VTT is proud to introduce the first and only plug-and-play crankcase breather kit designed for BMW applications utilizing the two-prong oil cap style.
Installation is simple—remove your factory oil cap, install the breather, and immediately:
- Reduce crankcase pressure
- Improve turbo oil drainage
- Free up horsepower
- Add a clean, performance-focused look to your engine bay
Versatile Performance
This breather can be:
- Used with the stock PCV system to relieve crankcase pressure
- Paired with aftermarket PCV setups for maximum pressure relief
Premium Construction
Machined from 6061-T6 billet aluminum and anodized black for durability and corrosion resistance, the VTT breather is built to perform.
Features include:
- (4) Stainless steel internal baffles for superior oil control
- PTFE one-way check ball
- High-quality breather filter
- Secure clamp system
Together, these components ensure crankcase pressure is properly vented while maintaining effective oil separation.
Fitment
This breather fits most (not all) BMW engines utilizing the two-prong oil cap, including but not limited to:
- N54, N55, S55
- S54, S85
- S63, S63TU, N63
- Most BMW diesel models
⚠️ Important Notes:
- Fitment may vary depending on valve cover design and surrounding components
- We do not recommend use on S63, S63TU, or S68 platforms (F90, G90 M5, etc.)
- Installation on non-recommended applications is at your own risk and renders the item non-returnable if used
-
Looking to adapt your wheel bore size to a smaller hub bore? VTT has you covered with our hub-centric adapters. These adapters are made from Billet 6061-T6 aluminum, and anodized in black. We have these sizes currently
- 57.1mm hub to 60.1mm wheel bore
- 57.1mm hub to 64.1mm wheel bore
- 57.1mm hub to 66.1mm wheel bore
- 57.1mm hub to 66.6mm wheel bore
- 57.1mm hub to 67.1mm wheel bore
- 57.1mm hub to 70.3mm wheel bore
- 57.1mm hub to 71.6mm wheel bore
- 57.1mm hub to 72.6mm wheel bore
- 57.1mm hub to 73mm wheel bore
- 57.1mm hub to 74mm wheel bore
- 57.1mm hub to 74.1mm wheel bore
- 64.1mm hub to 72.6mm wheel bore
- 66.6mm hub to 72.6mm wheel bore
They are sold in sets of two, order TWO SETS for a full car, or one set per axle.
-
Product Release: VTT Billet Installation Dowels
Ever tried wrestling a BMW transfer case into a car on your own? Or struggled to line up a transmission or subframe as you're sliding it into place? If you have, you know just how tedious—and downright frustrating—it can be.
After doing these installs hundreds of times, we used to rely on cut-off factory bolts to help guide components into place. But cutting bolts for different applications turned out to be a hassle—time-consuming, inconsistent, and often not long enough to provide the guidance needed.
So we created a better solution: VTT Billet Aluminum Installation Dowels—designed specifically to make these installations easier, faster, and more accurate.
Key Features:
-
One universal length: 6 inches
- Bull nose for easy slip into the part being installed
-
Two thread sizes
-
Three thread pitches
-
Built-in 5mm hex in the end for easy install and removal
Available Thread Options:
-
M10 Standard Pitch – Ideal for BMW transfer case installs and more
-
M12 x 1.5 Fine Thread – Perfect for most BMW front and rear subframe installations
-
M12 Standard Pitch – Designed for BMW transmission installs
-
-
Secure Your AN Fittings the Right Way – Without the Damage
VTT now offers a complete line of precision Billet 6061-T6 Aluminum AN Wrenches, designed to grip without marring your fittings. Whether you're working with -3 or -20 AN sizes, we've got you covered.These wrenches are lightweight, durable, and anodized in 8 vibrant colors for a long-lasting finish and easy size identification.
Available Options:
-
Full Kit: Includes all sizes from -3 to -20
-
Common Size Kit: Includes -4, -6, -8, -10, and -12
-
Individual Wrenches: Purchase only the sizes you need
-
-
VTT Billet CNC Oil Caps
Upgrade your BMW engine bay with a touch of precision and durability. VTT Billet CNC Oil Caps replace the factory plastic cap with a high-quality, performance-focused alternative.
-
Premium Materials – Machined from 6061-T6 aircraft-grade aluminum with stainless steel locking tabs for a secure fit and long-lasting reliability.
-
Anodized Finishes – Available in red, black, blue, purple, gold, or clear anodizing to match your build’s style.
-
Perfect Fitment – Designed for all BMW engines with a two-prong locking tab oil cap design, including (but not limited to):
THIS CAP DOES NOT FIT, B58TU, S58, A90/91 SUPRA, THIS ONLY FITS 2 PRONG CAP STYLE
-
-
VTT Billet Coolant Reservoir Cap – BMW
Upgrade your engine bay and eliminate the factory plastic with the VTT Billet Coolant Reservoir Cap. This CNC-machined aluminum cap replaces the OEM plastic unit, giving you strength, style, and long-term durability while retaining all OEM functionality. Simply snap the factory pressure-relief valve into place, and you’re ready to go.
-
Premium Construction – CNC-machined from 6061-T6 aluminum.
-
Factory Functionality – Accepts the OEM pressure-relief insert for proper venting.
-
Cohesive Design – Matches our N5X Billet Oil Cap, N5X Billet Oil Filter Housing Cap, and Billet Power Steering Cap for a uniform, high-end look.
-
Color Options – Available in Red, Black, Blue, and Clear anodizing.
-
-
Looking to maximize your E9/8X Series BMW for drag racing? Want to be able to dial in the perfect amount of compression or rebound on your launch? The VTT Double adjust drag shock kit is just want the doctor ordered!
-
Looking to ditch your factory wheel lugs and upgrade to a high-quality stud kit—whether for track use or simply to make wheel changes faster and easier? VTT has you covered with our Wheel Stud Conversion Kits, engineered for strength, reliability, and long-term durability.
Our studs are forged from cold-rolled 10.9-class steel and finished with a black oxide corrosion-resistant coating, ensuring years of dependable service in both street and motorsport environments.
We offer one optimized size: 85mm overall length, with the following breakdown:
-
75mm total thread length
-
10mm bull nose for smooth lug engagement
-
12mm short-thread section (hub side)
-
12mm unthreaded shank
-
48mm long-thread section (lug nut side)
These studs are coated using Black Oxide, which does protect, BUT even when using Black Oxide, the studs CAN develop surface rust if left to the elements. We suggest a slight coat of WD-40 when you clean your wheels to prevent this.
-
-
Looking to up your boost limit on just about any BMW vehicle that runs a 3 or 4-wire BMW map sensor including but not limited to S58, B58, N54, N55, S55, S63, B48, B47, B42, B57, B46? We were too, so we decided to make a very easy plug-and-play kit for 3, and 4-wire BMW map sensors. These kits will allow you to completely replace the 3-wire sensor with one of our sensors, leave your stock 4-wire in place for IAT sensing, and move the power, ground, and sensor signal from the factory sensor to our sensor. These sensors have the proper scaling which will allow your tuner to simply change your map sensor scaling in the tune, and the factory ECU will be able to utilize the sensor voltage with no problem. We are offering these in 5 bar (58 psi), and 6 bar (72 psi), and each comes with a plug-and-play harness, and optional fittings for ease of installation.
Note: For the S58/B58 our Factory style Pre-Throttle map sensor is also 5 bar, and will work fine coupled with the post throttle kit, but the scaling is different, if you want matching Voltages Pre/Post throttle you can run two of these.
A variety of install pics can be found below and - Here
Scaling PDF Links: 5-Bar / 6-Bar
Features include:- Plug and Play harnesses with no wire splicing
- Output wire for connecting a PI or external controller to your post-throttle map sensor for the most stable signal that is not affected by throttle closure
- Different fittings are available for your plumbing needs.
- Can have matching voltage signals for pre/post throttle for ease of tuning, and boost reference
- B58/S58 etc Pre Throttle - 3 Wire Harness (Charge pipe to 1/8" NPT adapter needed, for B58/S58 90 degree adapter needed to provide sensor clearance)
- B58/S58 Post Throttle - 4 Wire Harness (Boost reference will be needed from manifold to sensor)
- F90 M5 Pre/Post Throttle - 4 Wire Harness (May need to repin) (Boost reference will be needed from manifold to sensor)
- Most all other platforms Pre/Post Throttle - 4 Wire Harness (May need to repin) (Boost reference will be needed from manifold to sensor)
- B58
- S58
- S63/ S63TU
- N63
- N54
- S55
- N55
- N20
- B46
- B48
- B57
- B47
-
VTT is proud to offer a truly plug-and-play line lock kit for select BMW vehicles that does NOT require running wiring inside the car, mounted switches, holes in the dash, etc. Our newly designed and released line lock kits use a 40amp wireless remote control switch with 4 different modes that allow you to tailor your line lock setup exactly as you prefer. You simply install the solenoids, install the harness with the switch which has all the wiring terminated, bleed the brakes, and you are ready for effortless burnouts which will not be interfered with by the DME because you are holding the brakes, nor wear your rear brake pads. You can store the remote anywhere in your vehicle, center console, cup holder, door cup holder, etc., and when you need to do a burnout to heat your race tires it's in arm's reach without running any wiring into the vehicle. Fitment is confirmed for G8X M3/4, A9X Supra - The kit itself including lines, solenoids, etc will fit most all late model BMW Chassis including F8X, F3X, G2X, etc. The main concern will be mounting the wireless switch in the passenger cowl area. The kit includes:
- Line lock solenoids with weather pack connectors
- Two Parker 90-degree -3 an fittings
- Two Stainless Steel adapter fittings
- Two DOT Approved Stainless Steel brake lines
- One complete wiring harness
- One Remote control switch with TWO remotes
-
Looking to convert your 5×120 or 5x112 vehicle to 5x114.3 wheels, or 5x120 wheels, and open up your wheel options DRAMATICALLY? We got covered with our VTT wheel spacer conversion kits. These kits are machined from billet 6061-T6 aluminum and anodized for a long-lasting finish. We then press in 10.9 class studs, with corrosion-resistant zinc coating for years of use. The spacer then accepts either a 5x114 wheel or a 5x120 wheel. The 5x114 use M14 studs, and the 5x120 use M12 studs. All the spacers have either a 66.6mm or 72.6mm Hub bore size to fit 99% of BMW applications.
QTY 1 is for ONE SPACER. If you need to do 4 wheels order FOUR!
We offer Hub-Centric adapter rings to fit other wheel bore sizes No wobble bolts or redrilling here. We offer these in 4 thicknesses 15mm, 17.5mm, 20mm, and 25mm. The studs coming out of the spacer are 40″ total length and come with Black Lugnuts. Spacers that convert to 5x120 have M12 studs, ALL others have M14x1.5 -
Looking to make sure all metal contaminates that are possibly in your oil are not circulated? VTT has you covered with our Titanium Magnetic oil drain plugs for BMW, and any other vehicle that uses an M12x1.5 drain plug. This drain plug will capture any ferrous metal particles in your oil, and capture them to be cleaned during your next oil change. It also is stronger than a Steel or Aluminum drain plug, and looks cool! These are made from GR5 Titanium and use a rare earth magnet to capture metal particles in your oil... Kit includes:
- 1 Titanium Drain Plug
- 1 M12 Crush Washer
-
Tired of your Dragy flying all over the car as you try to do runs? Tired of low sats or no sats warning due to improper location of the Dragy in the vehicle? Well say goodbye to those issues with our new Carbon Fiber and Plastic Dragy holders. These are made from either 100% Pre-Preg Carbon Fiber, or molded plastic for a perfect fit. The carbon fiber gives it just the right look to add to your performance vehicle! Each holder has dual Suction cups and will stick to any smooth surface. We suggest mounting them in the upper left or right corner of your windshield with a full view of the sky. Dragy holder features
- Stop your Dragy from flying off the dash, and having to search for it
- Position your Dragy in the optimal position for the best satellite coverage
- VTT Dragy holder exposes the entire top of the Dragy so nothing is blocking the receiver from the Satellite
- The charging port is not blocked and can be accessed with the cover on
- Choose from REAL Carbon Fiber or Molded Plastic
-
VTT “Ultimate” Front Drag Brake Kit
E-Series & F-Series BMW
Looking to make your E or F-Series BMW faster in the 1/4-mile or 1/2-mile?
Want to run 17" or even 15" front wheels?
Want to drop OVER 54 lbs of unsprung weight off the nose of the car while improving weight transfer — without breaking the bank?
The VTT Ultimate Front Drag Kit is engineered specifically for straight-line performance. This system allows you to run the wheel and tire combination needed to lower ETs while dramatically reducing unsprung and rotational mass compared to the factory steel front brake setup.
Less weight.
This kit comes in 1 variation, with two different caliper Options for each. We HIGHLY suggest 6-piston Calipers for street driving and 1/2 mile racing. These calipers will drop weight, AND be a braking upgrade over stock calipers.
More clearance.
Better weight transfer.
Faster passes.Pictures are for REFERENCE ONLY. All kits will come with varying hardware, brackets, and mounting styles based on the platform.
-
VTT ultimate E8/9X ultimate rear brake conversion kit VTT is happy to announce its new rear brake conversion kits for the E8X/E9X platforms. We take what already exists on the market, and make it much more complete, and much more performance-oriented while keeping the clearance for those 15” wheels. This kit replaces your rear brake rotors and calipers to fit 15″ wheels. It includes lightweight VTT calipers to go from the single-piston factory caliper to race-inspired 4-piston calipers. While dropping up to a whopping 20 LBS of unsprung weight off the back of your vehicle!
Pictures are for REFERENCE ONLY. All kits will come with varying hardware, brackets, and mounting styles based on the platform.
-
VTT Carbon Fiber headlight duct for the E90 will complete any racecar or streetcar build helping to get rid of weight and add functionality with a working 6″ velocity stack to run your turbocharger into for optimal flow, and ram air. 100% multi-layer prepreg Carbon Fiber, with a UV resistant clear coat for the ultimate in strength, and durability! We offer them in the following varieties: Passenger side duct with 6″ Velocity stack 3″ hose connection Passenger side duct with 6″ Velocity stack 4″ hose connection
FITMENT: PLEASE NOTE IT FITS ALL E90, AND E91 MODELS INCLUDING M3, ETC. THIS LIGHT HAS NOT BEEN TEST FIT ON AN LCI VEHICLE, AND WE CAN NOT CONFIRM IT FITS LCI. WE CAN ONLY CONFIRM PRE-LCI FITMENT AT THIS TIME.
-
VTT -16 Billet HIGH-FLOW Catch Can System
Maximum Venting for Maximum Power
VTT is proud to introduce our -16 Billet High-Flow Catch Can System — designed from the ground up for high-horsepower applications requiring serious crankcase ventilation. Whether you're pushing over 900WHP or beyond 2000WHP, this system delivers unmatched performance, reliability, and engine bay cleanliness.
Key Features:
-
Supports -16 AN lines (with optional -12 or -20 fittings)
- 20 Fluid OZ capacity
-
Engineered for big-power builds needing high crankcase pressure relief
-
Triple-stage filtration system to eliminate oil mist — even in the event of engine failure
-
Designed, tested, and proven to keep oil inside the catch can — not in your engine bay
Triple Filtration Technology:
-
Stage 1 - Stainless steel filter – captures 95% of oil mist on entry
-
Stage 2 - Perforated diffuser plate – further disperses and slows down airflow
-
Stage 3 - Final stainless mesh layer – scrubs out any remaining vapor before venting
This advanced system has been tested with over 200 PSI of pressure and more than half a quart of oil without releasing a trace of oil mist. As long as the catch can is properly serviced and not overfilled, even catastrophic engine failure won’t result in a mess under your hood.
Application-Specific Kits Available:
We offer plug-and-play kits for popular platforms, including:
-
G8X M2/M3/M4 (S58) SINGLE TURBO ONLY
-
F9X X3M/X4M SINGLE SINGLE TURBO ONLY
-
A9X Toyota Supra
Each Plug and play kit includes everything needed for installation: catch can, vehicle-specific bracket, fittings, hoses, and optional drain. Again, plug-and-play kits include ALL required parts. Bracket, fittings, line, etc. No additional fittings are required except the drain if wanted.
-
-
VTT High-Performance Ignition Coils
BMW N5X • B58 / S58 / B48 • VAG Platforms
Vargas Turbo Technologies (VTT) is proud to offer high-performance ignition coil upgrades for BMW N5X platforms, B58/S58/B48 engines, and select VAG applications.
Development & Testing
Our ignition coil program began with extensive outreach to multiple OEM and aftermarket coil manufacturers. We commissioned individual prototype coils, then subjected them to rigorous, repeatable testing in the United States to ensure they matched or exceeded factory performance standards.
Only the highest-performing designs were selected and produced to VTT’s exact specifications and colorways. These are not rebranded or cosmetic coils—each set is performance-validated.
-
VTT Billet Power Steering Cap – BMW
VTT is proud to introduce our billet aluminum replacement for the factory plastic BMW power steering cap. Designed to eliminate the weak OEM plastic cap, this upgrade delivers both durability and style while retaining all OEM functionality, including the built-in dipstick and vent provision.
-
Premium Construction – CNC-machined from 6061-T6 aluminum, anodized in your choice of finish.
-
Factory Functionality – Full dipstick and vent hole integration, just like OEM.
-
Cohesive Design – Matches perfectly with our N5X Billet Oil Cap and N5X Billet Oil Filter Housing Cap for a complete, uniform look.
-
Bundle Option – Order all three (Oil Cap, Oil Filter Housing Cap, and Power Steering Cap) for $175.
-
Color Options – Red, Black, Blue, and Clear anodizing.
-
-
This is an easy way to order all 3 VTT Billet engine caps for Valve Cover, Power steering, and Oil Filter Cap. We offer these caps in 4 colors - Red, Black, Blue, and Clear anodize
-
VTT Billet Oil Filter Housing Cap – BMW N5X / S55 / N20
VTT is proud to introduce our billet aluminum replacement for the factory plastic oil filter housing cap. Built for both performance and style, this upgrade eliminates the weak OEM plastic cap while also removing the need for a special tool during filter changes.
-
Premium Construction – CNC-machined from 6061-T6 aluminum with precision cooling fins to help reduce oil temps.
-
Factory Functionality – Retains all OEM provisions for the filter basket, including the lower pins essential for proper bypass valve function.
-
Easy Serviceability – Features a 19mm hex head for quick installation and removal with standard tools.
-
Complete Package – Includes a new sealing O-ring and small O-ring for the filter cage.
-
Color Options – Available in Red, Black, Blue, and Clear anodizing.
-
Cohesive Design – Matches perfectly with our N5X Billet Oil Cap and N5X Billet Power Steering Cap for a clean, uniform look under the hood.
-
Bundle Option – Get all three caps (Oil Cap, Oil Filter Housing Cap, and Power Steering Cap) for $175 – a 10% savings.
-
-
Give the Gift of VTT! Looking to get your friends, or family some go-fast parts, and no idea what they need, only that they love VTT? Well, our Gift Cards have you covered! They come in $50, $100, $250, $500, and $1000 increments. Each gift card is precision cut out of plastic in the shape of the VTT logo and has the dollar amount and the code on the back. Each gift code is unique and is locked to that card. To redeem simply enter the code during check out it will remove that amount, and if you have any leftover it will go back to the card.
You can choose to have your card physically mailed to you, or a virtual card where we can send you a scan of your card.
-
VTT Billet Wheel Spacers
VTT is proud to offer billet wheel spacers for most VAG, BMW, and the A90/91 Toyota Supra platforms.
Each spacer is:
-
CNC-machined from 6061-T6 aluminum
-
Hard anodized black for a long, corrosion-free life
We offer multiple fitments and sizes to suit a wide range of applications.
THESE ARE SOLD INDIVIDUALLY, FOR ONE AXLE ORDER TWO FOR A COMPLETE SET ORDER FOUR.
ANYTHING OVER 5MM WILL REQUIRE LONGER BOLTS OR STUDS. YOU CAN CHOOSE TO ADD A VTT WHEEL STUD KIT FROM THE OPTIONS.
PLEASE DOUBLE CHECK YOUR BOLT PATTERN AND HUB BORE BEFORE YOU ORDER. INSTALLED SPACERS CANNOT BE RETURNED!
-
-
Please Note: This is a Virtual Gift Card. After purchase you will receive an email with your Gift Card code
-
Need a Tee fitting for plumbing Vacuum, or Boost lines, Don't want to use cheap plastic ones that can get soft when hard, and brittle after they heat cycle? We didn't either, which is why we machined these high-quality billet tees to solve this issue. Machine from 6061-T6 aluminum, and anodized in black for a long-lasting corrosion-free finish, these tees look great, and will you never have to worry about one failing. We offer them in two sizes, each size has 12mm legs and 3 barbs:
- 7.60mm / -4 Push Lock for people looking to use -4 push lock hose or -4 AN hose. This is a perfect fit for those.
- 1/4" For people looking to use 1/4" vacuum tube
-
Are you building a single kit for the N54, N55, or S55 platform? M7 Locking exhaust nuts is not easy. So we made our own to combat the issue. These are the perfect solution to the problem of hard-to-find M7 lock nuts. Sold individually so order the number you need.
Note: This is nuts ONLY Stud not included, by our extended M7 studs here - https://vargasturbo.com/product/vtt-fab-extended-m7-n54-n55-s55-b58-2-port-head-studs/
-
VTT/PFS Stainless Steel Fuel Strainer for Walbro In-Tank Pumps
The fuel system is one of the most critical components of your entire build—it delivers the fuel that translates into big power and fast times! Without proper filtration, your Walbro 274, 285, or 295 fuel pump can ingest contaminants, leading to premature failure. However, choosing the right strainer or pre-filter is just as important as post-filtration. 🚨 Why Does Your Fuel Pump Need the Right Strainer? ✅ Too fine of a filter can restrict flow and cause the inlet to collapse. ✅ Too coarse of a filter can allow debris to pass through, damaging the pump and engine. ✅ Low-quality materials can break down, collapse, or cause fueling issues—leading to potential engine failure.The VTT/PFS Stainless Steel Fuel Strainer – The Ultimate Solution
