-
VTT is proud to offer the very best EASY-TO-INSTALL charge pipe solution for the 2013-2018 Cummins platform. This system completely does away with the restrictive, and muli-connection stock charge pipe system, and replaces it with two single 7-ply, Heat Resistant, Wire reinforced silicone charge pipes rated at over 250 psi. DON'T struggle trying to install aftermarket hard pipes with 8 clamps, and cuss-worthy space to try to squeeze them in! These are molded for the perfect fit in your engine bay, while not sacrificing anything in the way of flow or size. They also completely isolate your charge air from any additional heat soak coming in from the engine or ambient heat. The stock hot side pipes have many irregular shapes and turns causing turbulence as well as carrying heat.
-
VTT 6 Piston Caliper upgrade (Must own 4 piston kit)
$1,049.99 – $1,109.99 -
Sale!
VTT Audi/VW/Porsche Billet Oil Cap
$59.99$54.99Looking to spice up the engine bay of your Audi/VW or Porsche without spending a ton of money. Our Billet Oil caps come in 5 colors and will look great in any engine bay. CNC machined from a billet of 6061-T6 Aircraft aluminum they sport a factory fit and finish with a Viton O-ring for long a leak-free life. They fit a WIDE variety of vehicles and directly replace your factory oil cap. -
Looking to remove your BOV either for leak testing, or dont want to run one, and your charge pipe or housing has a flange on it. You can use this billet plate to block off the BOV flange. Uses the O-ring from the BOV to seal, and removes the BOV. Fitment: Tial BOV Turbosmart BOV with female flange like Tial
-
Sale!
VTT Billet Check Valves
$24.99 – $29.99VTT CNC Billet check valve that can be used for a variety of uses including a vacuum/boost check valve when removing the stock PCV system, and still wanting to run vacuum to the crankcase. Rated at over 100 psi, with a cracking psi of .25psi. -
VTT Billet Crankcase Breather replacement filter
$19.99 – $24.99Need a replacement filter for your VTT Billet Crankcase breather? You can order on here. We offer them in 3 heights, low 48mm, medium58mm, and tall 68mm. This is measured from base to top. The filter will include a new clamp. For reference: N54/55 mostly use the low A90 Supra use Medium Most Audi applications can fit a tall, but measure your filter before ordering. -
Looking to adapt your wheel bore size to a smaller hub bore? VTT has you covered with our hub-centric adapters. These adapters are made from Billet 6061-T6 aluminum, and anodized in black. We have these sizes currently
- 57.1mm hub to 60.1mm wheel bore
- 57.1mm hub to 64.1mm wheel bore
- 57.1mm hub to 66.1mm wheel bore
- 57.1mm hub to 66.6mm wheel bore
- 57.1mm hub to 67.1mm wheel bore
- 57.1mm hub to 70.3mm wheel bore
- 57.1mm hub to 71.6mm wheel bore
- 57.1mm hub to 72.6mm wheel bore
- 57.1mm hub to 73mm wheel bore
- 57.1mm hub to 74mm wheel bore
- 57.1mm hub to 74.1mm wheel bore
- 64.1mm hub to 72.6mm wheel bore
- 66.6mm hub to 72.6mm wheel bore
They are sold in sets of two, order TWO SETS for a full car, or one set per axle.
-
VTT is happy to offer our very unique and universal billet mount to fit any roll bar or cage with 1.5", 1.75", or 2" diameter tubing. These mounts are designed from 6061-T6 aluminum and are made to SECURELY hold a JBL Flip version 3 - Version 6 and allows you to bring music into your race car, off-road vehicle, rock crawler, boat, basically anything that has a length of tubing this will allow you to have an easy way to have tunes without having to install and mount a stereo system. They can also be used as a single mount to hold things such as a helmet, steering wheel, or anything you want to quickly hang for easy access once seated. For the JBL flip you will need TWO mounts, simply install them loosely, snap in your JBL Flip to get the proper spacing, and tighten down. The device is then securely mounted and can be removed easily. We offer these in a variety of anodized colors for a long-lasting durable finish including Black, Red, Blue, Clear, Orange, and Green Mounts are sold individually Features:
- Billet 6061-T6 Aluminum construction anodized in a variety of colors
- Can be used to SECURELY mount a JBL Flip 3-6 to anything that has a length of 1.5", 1.75" or 2" tubing
- Can also be used as a universal mount for anything you need to hang in your race car, off-road vehicle, etc
- Completely reversible, and can be moved from vehicle to vehicle
-
VTT Brake Kits Rotors/Hats only
$109.99 – $249.00This is for those running our brake kits that use our 11.75" or 13" Rotors that want to easily change between rotors for dedicated drag racing and street use. You can now buy Rotor/Hat Assemblies by themselves to switch between any of our 3 options- Scalloped (Recommended Drag use with parachute only)
- VTT HD ( Drag Use, Heavy Street duties, 1/2 Mile events, etc)
The price is for ONE ROTOR / OR ONE ROTOR/HAT ASSEMBLY
-
VTT Carbon Fiber Dragy Holder
$19.99 – $49.00Tired of your Dragy flying all over the car as you try to do runs? Tired of low sats or no sats warning due to improper location of the Dragy in the vehicle? Well say goodbye to those issues with our new Carbon Fiber and Plastic Dragy holders. These are made from either 100% Pre-Preg Carbon Fiber, or molded plastic for a perfect fit. The carbon fiber gives it just the right look to add to your performance vehicle! Each holder has dual Suction cups and will stick to any smooth surface. We suggest mounting them in the upper left or right corner of your windshield with a full view of the sky. Dragy holder features- Stop your Dragy from flying off the dash, and having to search for it
- Position your Dragy in the optimal position for the best satellite coverage
- VTT Dragy holder exposes the entire top of the Dragy so nothing is blocking the receiver from the Satellite
- The charging port is not blocked and can be accessed with the cover on
- Choose from REAL Carbon Fiber or Molded Plastic
-
VTT Ignition Coil Kits
$159.99 – $209.99VTT is proud to offer ignition coil replacements for the N5X platforms, as well as B5X, and many VAG platforms. We started our quest for coils by contacting multiple coil manufacturing companies, paying for individual coils to be made then putting them through rigorous testing in the USA to ensure they matched or exceeded factory output. Once we were satisfied with the testing, we had the best performing coils made to our colors and specs. We offer these coils as complete sets for the N54, B58/S58, and the VAG platforms in either 4, or 5 cylinders. We also offer upgraded plugs which are highly recommended to change when doing coil replacements These coils come in 3 colors, Red, Black, and Blue, and are not simply an aesthetic upgrade but match or exceed the factory secondary spark energy. The VAG coil, is extremely potent, and the tester was so impressed with it compared to the factory coil, he called it a "BEAST" of a coilNote: To extract maximum performance from VTT coils minor tune changes are required to optimize dwell periods. See recommended Dwell times below
-
VTT M14/M12 Titanium Wheel Stud kits
$159.99 – $319.99VTT is proud to offer Titanium wheel stud kits for the owner looking for the lowest possible unsprung weight while maintaining high strength, and good looks as all come with an amazing burnt finish. This kit is 60% lighter than factory steel studs and nuts with a total kit of 20 nuts, and studs being 3.1LBS. Sets of 10 are 1.55 lbs -
VTT is proud to offer the very best charge pipe solution for the VAG MK7 Golf/Jetta/A3 platforms. This system completely does away with the restrictive, and muli-connection stock charge pipe system, and replaces it with two single 6-ply, Heat Resistant, Wire reinforced silicone charge pipes rated at over 200 psi. They are molded for the perfect fit in your engine bay, while not sacrificing anything in the way of flow or size.
-
VTT MK7/MQB Ultimate Front Drag Brake Kit
$1,159.99 – $1,849.99Looking to make your MK7 GTi, Golf R, Jetta, etc, faster in the 1/4 mile or 1/2 mile racing? Want to run 15" wheels, and slicks in the front? Want to drop 63 lbs of weight off the front of the car at the same time? Do not want to break the bank while doing so? Look no further than the VTT Ultimake Front Drag kit for the MK7 platforms. This kit will allow you to run the wheel/tire combo you need to drop your ET's all while putting the car on a significant diet over the stock front brake set up. The kit is a true plug-and-play set up using VTT/Genuine Wilwood parts, coupled with DOT-approved brake lines, CNC rotor hats/brackets, and a CEL eliminator harness for the brake sensor. This kit comes in 3 different variations in 2 different caliper sizes -
VTT MQB Cast V2 “GC” Turbo Upgrade – G30-770/900
$1,599.00 – $1,999.00GC Stock-550WHP / GC+ stock-600WHPBALL BEARING NOW AVAILABLE!
Ready to take your MQB powered platform to the next level? Don’t want to deal with core charges, long lead times, or restrictive factory housings? Look no further! VTT has you covered with our 100% new casting V2 “GC” turbocharger upgrade. We start by keeping the great design elements of the factory turbo and removing the not-so-great ones such as the small factory inlet area, turbo muffler on the outlet, bearing housing oil structure, thrust bearing, and anything else we saw that could be improved upon. This is not your basic IHI CHRA. We completely changed the bearing structure to an new turbine shaft, and journal bearing making it larger than anything in the IHI IS20 or IS38 family, this truly is a custom unit. We also increased the thrust assembly dramatically to deal with the increased thrust loads. With the basics covered, we stepped it up a level by adding proprietary VTT changes to the housings, A/R Ratios and finished off by having all these parts cast to OE quality. What this means for you is serious MQB power made easy; GCs are a drop-in turbocharger upgrade that supports up to 600WHP while maintaining very fast spool and all factory connections including oil, water, downpipe, and charge pipe. This turbo is perfect for the MQB owner looking to max out the factory fuel system and make their MQB more fun to drive with power to redline, as well as the customer looking to add a fuel system and push towards the 550-600WHP range. This truly is the unit for everyone.
