-
Unsure of the state of your CHRA's, whether brand new from a questionable source or rebuilt? DON'T install them without having a proper High-Speed balance done! This is the #1 most critical factor when building a turbocharger, and is even more important for performance turbochargers or small twins that see a LOT of RPM. We use a Turbo Technics VS3 balancer, and balance most units down to under .5G Not all turbos will be able to pass a high-speed balancing test for any number of reasons (usually poor assembly, bent shaft, etc), if they will not pass, we will send you the specs they are in, and as close as we could get them. We then will give you the option to send them back, or we can disassemble, and rebuild them in-house using our other balancing, and assembly tools to ensure a properly built/balanced unit. The service is $79.99 each for most turbos, and we have the capabilities to balance most units. If sending in twins please choose TWO as the quantity
UNITS MUST BE SENT IN WITH NO HOUSINGS, AND IN A CONDITION READY TO BE BALANCED, IF YOU NEED TO SEND IN COMPLETE TURBOS, WE CAN DISASSEMBLE, AND BALANCE FOR YOU, BUT AN EXTRA CHARGE WILL APPLY. IF THE UNITS ARE SENT IN A CONDITION WHERE THEY CAN NOT BE BALANCED WE WILL LET YOU KNOW THE PRICE TO GET THEM TO A STATE WHERE THEY CAN BE
-
One Ethanol Racing Fuel
$69.99 – $559.99Please note: Due to heavy increases in freight costs we have had to raise prices by $50 on 54-gallon drums, and $15 on pails.
VTT is proud to be the West Coast dealer for One Ethanol racing fuel.
We have two blends available in 5-gallon pails and 54-gallon drums. See below for descriptions of both fuels
Fuel is available for local pick up only unless you email, and make arrangements for freight shipping. Be aware fuel is considered hazmat and the freight charges are equal to or more than the fuel in all instances. Fuel CANNOT be shipped normal shipping methods such as UPS, FED EX, etc
-
Replace your failed OEM fuel pump with a PFS OEM replacement. These are tested to flow the same as stock, and will completely replace your LPFP with a brand new bucket. This also replaces the fuel filter as the filter is built-in into the bucket. Comes with a 1-year warranty
-
PTE – Precision Turbochargers
$2,234.49 – $4,428.99VTT is proud to offer PTE Turbocharger products! -
Looking to go above 31PSI on your VAG vehicle that uses SENT map sensors? If so you will need this 4-bar SENT sensor with integrated IAT. These are plug and play for most 2.5L engines including DAZA, and DNWA(US VERSION), as well as some other VAG platforms. You will need to have your tuner rescale your map for the sensor, but that is the only change needed. We offer them in pairs only, which is needed on most vehicles.
-
VTA Breather
$39.99Not available for single can external PCV Valve. -
VTT “1.4” Kit for Audi/VW Platforms
$4,519.99 – $5,459.99VTT Is proud to announce our "1.4" kit for VW/Audi Platforms. This kit is a COMPLETE kit for AWD vehicles looking to maximize their traction at the drag strip. This set up virtually guarantees a 1.4 or better 60 ft time, and your best ET before installing. The kit includes EVERYTHING needed to convert the vehicle to 15" wheels/Slicks at all 4 corners. -
VTT “DCS” EWG System for TurboSmart Straight Gates
$799.99 – $1,499.99VTT is proud to offer our EWG "Direct Control System" or DCS! This is a completely new innovation for people looking to control the highest-flowing wastegate on the market using an existing BMW electronic actuator. This system will allow BMW owners who have a vehicle with Electronic Wastegates from the factory to utilize this system to control an externally wastegated turbo system, AND it will ALSO allow ANY vehicle to use this setup to control your own custom turbo system. This is done by utilizing our custom 7075 Billet aluminum bracket coupled with a Turbosmart Straight gate, and if needed an EWG controller made for us by DCCD Pro. This allows direct external wastegate control over any turbocharger system with or without EWG for the factory. Features:- Utilizes the most current wastegate technology the Turbosmart Straight Gate. This gate allows maximum flow with minimal restriction, low drive pressure, and much more. Full details can be found here - https://www.turbosmart.com/product/electronic-straightgate-esg50-external-wastegate/
- Can be configured in multiple ways, and angles based on how you mount the adapter
- The adapter is 7075 Aluminum which has the strength of steel and weight of aluminum
- All connection fittings, are made from Nitronic 60 which has extremely high temperature and wear properties
- Zero Drive Pressure, no springs, no poppet valves, direct control over the gate using factory ECU logic
- Adaptable to ANY turbo system on any car to provide the ultimate in boost control!
-
VTT is proud to offer our "OBD-LOCK" OBD port locking tool. This tool is made from billet 6061-T6 aluminum and is designed to completely lock out your OBD port from being accessed. This is useful for people who do not want dealers, techs, etc from accessing their OBD port, and possibly changing a tune, etc. This is also perfect for anti-theft prevention as it will not allow a would-be thief to hook up to the car's OBD port, duplicate a key, etc. The OBD-LOCK cannot be removed without physically destroying the OBD port if you do not have the proper tools. VTT uses 5 types of screw head designs for every 200 OBD-LOCKS made. This means that worldwide only 40 OBD-LOCKS are using the same head design. For each batch of 200, we redesign the screw heads meaning every batch of 200 OBD-LOCKS will use different screw heads and tools. Each OBD-LOCK sent has its head design chosen at random. After Extensive testing, we have found that our OBD lock fits EVERY SINGLE OBD port we have tried, this means it will fit every single OBD port currently on the market from a high-end BMW to a Ford F150 diesel. If you order one, and find it does not fit, PLEASE let us know.
FITMENT: We have TWO versions one for ALL GM vehicles and one for ALL NON-GM Vehicles. Please order the one you
-
Show off your VTT support and get a good laugh from people with our "We Like To Party" License plate bracket. Born from the infamous quote in Talladega nights
-
Looking to protect your single turbo investment, dont have a ton of room, and need a low profile filter that can flow what you need? VTT Has you covered with our Low Profile Single turbo Air Filters. These filters are custom-made for VTT. They are made with a heat-resistant silicone base, and a high-flowing cotton weave element with a pre-oiled design to catch contaminates but allow free flow. We currently offer them in Black, and 3 flange sizes. 3", 4" and 5" flange. With two filter heights. Tested at over 1200WHP with no loss of power observed. Filter Options - Offered in White, and Black with the following dimensions Short - 3.75" Tall, 7.5" OD Large end, 5" Small end 3", 4", or 5" Flange Tall - 4.5" Tall, 7.5" OD Large end, 5" Small end 3", 4", or 5" Flange
-
Sale!
VTT 1.8/2.0 MQB COMPLETE Catch Can System
$699.00$689.99With the VTT COMPLETE Catch can set up, we completely address the low AND high sides, by separating them, and running each side into its own chamber in the catch can. We do this using a custom PCV plate, that organizes the HIGH and LOW sides into nice short hose runs and uses strategically placed check valves to keep boost out of your crankcase, and in the manifold where it belongs. Our opening in the PCV plate is baffled, and the plate chambers themselves are filled with Stainless mesh to knock down any oil mist, and the catch can is also filled with this mesh. This means any oil is knocked out of the air BEFORE it gets to your intake ports or turbocharger inlet. We completely redesigned what people think of then they see an MQB catch can set up. VOLUME in the PCV system is just as important as the vacuum itself. Every set on the market runs lines across the ENTIRE engine bay, this long run, mean vacuum drop, and volume loss, this equals poor PCV operation. Our system mounts the can directly over the cold side of the turbocharger against the firewall, and the longest hose run is only a little over 9". We also use all custom CNC aluminum Banjo fittings, and Banjo Bolts, even our check valves are custom fitted into banjo Fittings. The -6 Banjo that pulls vacuum for the low side also serves as a place to run a boost tap if wanted. This makes it easy to run a boost reference for BOV, Boost gauge, 1:1 FPR reference, etc. -
Sale!
VTT 15″/17″ Drag Pack Wheels for BMW/Toyota/VAG
$269.99 – $349.99Looking for a Lightweight, AFFORDABLE drag pack that looks amazing for your BMW, Toyota, or VAG platform? Look no further! VTT is proud to announce our lineup of Drag pack wheels for various BMW/Toyota/VAG fitments! We teamed up with Rota and had them open custom molds for us of their extremely popular Grid design. With these molds, we have an exclusive on 15X10, 17X10, and 17X4.5 wheels in our exact specs. The wheels currently are offered in the colors and sizes belowWe chose ET45 across the board on the rear as this is a universally easy offset to fit and can be made to fit just about any application with the use of a spacer. - VTT Spacers can be found here - https://vargasturbo.com/product/vtt-billet-wheel-spacers/
Wheels are priced EACH, meaning per wheel
PLEASE NOTE! CHECK FITMENT CAREFULLY. ANY WHEELS THAT HAVE HAD TIRES MOUNTED OR ARE DAMAGED DURING TEST FITTING ETC ARE NOT RETURNABLE!
We make NO CLAIM these fit ANY PLATFORM, or ANY factory brake set up. It is YOUR JOB to measure, and make sure they will fit BEFORE you mount tires or install them. WE NEVER suggest shaving down brake calipers to fit a smaller wheel. If they do not fit. GET A SMALL BRAKE KIT!
Colors offered:- Satin Black
- Gloss Black
- Bronze,
- Gun Metallic
- 15x10 ET45 (wheel weight 16 lbs)
- 17x10 ET45 (wheel weight 19lbs)
- 17x4.5 ET-20 (wheel weight 16lbs)
- 15x10 ET45 - (wheel weight 16 lbs)
- 17x10 ET45 (wheel weight 19 lbs)
- 17x4.5 ET-20 (wheel weight 16 lbs)
