-
Are you building a single kit for the N54, N55, or S55 platform? The stock studs are usually a little bit short for most single-head flanges, and finding M7 studs is not easy. So we made our own longer studs to combat the issue. Made from 10.9 grade steel, and coated in black oxide, these are the perfect solution to the short stud problem. Sold individually so order the number you need. Stud details are as follows
- Overall length 47mm (stock 39mm)
- 3mm shoulder
- 6mm head which is 5mm hex
- 14mm short end
- 24mm long end (stock 15mm)
Dont forget our M7 copper lock nuts as well to complete the job - https://vargasturbo.com/product/vtt-fab-m7-copper-locking-exhaust-nuts/
-
Are you building a single kit for the N54, N55, or S55 platform? M7 Locking exhaust nuts is not easy. So we made our own to combat the issue. These are the perfect solution to the problem of hard-to-find M7 lock nuts. Sold individually so order the number you need.
Note: This is nuts ONLY Stud not included, by our extended M7 studs here - https://vargasturbo.com/product/vtt-fab-extended-m7-n54-n55-s55-b58-2-port-head-studs/
-
Building a kit using Mac solenoids to control boost? Need an easy way to mount it? VTT-FAB has you covered with our billet Mac Solenoid brackets. Machined from 6061 billet and anodized in 3 colors, these are the perfect way to mount your Mac valve and look good while doing it. Each kit includes:
- One Mac Solenoid bracket (3-Port or 4-Port)
- 2 Allen screws to hold the valve to the bracket
- M6 Mounting Bolt
-
Looking to up your boost limit on just about any BMW vehicle that runs a 3 or 4-wire BMW map sensor including but not limited to S58, B58, N54, N55, S55, S63, B48, B47, B42, B57, B46? We were too, so we decided to make a very easy plug-and-play kit for 3, and 4-wire BMW map sensors. These kits will allow you to completely replace the 3-wire sensor with one of our sensors, leave your stock 4-wire in place for IAT sensing, and move the power, ground, and sensor signal from the factory sensor to our sensor. These sensors have the proper scaling which will allow your tuner to simply change your map sensor scaling in the tune, and the factory ECU will be able to utilize the sensor voltage with no problem. We are offering these in 5 bar (58 psi), and 6 bar (72 psi), and each comes with a plug-and-play harness, and optional fittings for ease of installation.
Note: For the S58/B58 our Factory style Pre-Throttle map sensor is also 5 bar, and will work fine coupled with the post throttle kit, but the scaling is different, if you want matching Voltages Pre/Post throttle you can run two of these.
A variety of install pics can be found below and - Here
Scaling PDF Links: 5-Bar / 6-Bar
Features include:- Plug and Play harnesses with no wire splicing
- Output wire for connecting a PI or external controller to your post-throttle map sensor for the most stable signal that is not affected by throttle closure
- Different fittings are available for your plumbing needs.
- Can have matching voltage signals for pre/post throttle for ease of tuning, and boost reference
- B58/S58 etc Pre Throttle - 3 Wire Harness (Charge pipe to 1/8" NPT adapter needed, for B58/S58 90 degree adapter needed to provide sensor clearance)
- B58/S58 Post Throttle - 4 Wire Harness (Boost reference will be needed from manifold to sensor)
- F90 M5 Pre/Post Throttle - 4 Wire Harness (May need to repin) (Boost reference will be needed from manifold to sensor)
- Most all other platforms Pre/Post Throttle - 4 Wire Harness (May need to repin) (Boost reference will be needed from manifold to sensor)
- B58
- S58
- S63/ S63TU
- N63
- N54
- S55
- N55
- N20
- B46
- B48
- B57
- B47
-
Looking for Mac solenoids for your build? We got em here at VTT-FAB so you can get everything in one place. We have 3-port, and 4-port in stock!
-
VTT S55/N55 EWG Cast Aluminum Valve Cover
VTT is proud to introduce our S55/N55 EWG Cast Aluminum Valve Cover, designed for performance-driven BMW owners looking for a durable, stylish, and functional upgrade. This option provides a cost-effective alternative to our billet valve cover while still delivering enhanced engine bay aesthetics and eliminating the failure-prone factory plastic cover, which can crack over time.
Beyond durability, this valve cover removes the problematic factory PCV system, giving you complete control over how you set up your PCV. We highly recommend pairing it with a catch can for optimal performance. Additionally, this cover is perfect for single turbo conversions, offering increased clearance and improved heat resistance.
-
We have a variety of fittings in stock to help you get your turbo system plumbed up! Available are:
- 1/8" NPT to -6 AN Male (Great for water lines, or anywhere you need a small 1/8" NPT to -6 Male AN)
- M14x1.5 to -6 AN Male (Great for water lines on Garrett turbos GT, GTX, and G-Series, or anything that has a metric M14x1.5 thread and you need a -6AN male)
- .035" Turbo feed restrictors. These are for Garrett turbochargers and will fit GT, GTX, and G- Series up to G35
- Garret GT, GTX, and G-Series up to G35 -8 An drain adapter. For those that want a low profile -8 drain for their GT-G-Series Garrett. (Comes with two bolts, and a gasket)
-
VTT-FAB Top-Mount Single Turbo Kit
For BMW F8X S55 Platform
VTT-FAB is proud to offer the premiere top-mount single turbo kit for the BMW F8X S55 platform. This system is 100% made in the USA at our Hayward, CA facility using only premium materials and components.
The heart of the kit is a hand-fabricated 321 stainless manifold with billet flanges for maximum flow and long-term durability. It’s paired with our factory-controlled external wastegate system featuring a Turbosmart 60mm Straight Gate. This design gives you complete wastegate control directly through your factory ECU tune — no external boxes, MAC solenoids, or vacuum lines required. Simply reuse your factory actuator with our adapter, and you have a true boost range from 0 PSI to the limits of your turbocharger.
⚠️ Important Notes
-
Please email [email protected] to confirm current build times.
-
Every kit is built to order and cannot be canceled once fabrication begins.
-
-
High-Boost Crankcase Ventilation Adapter for BMW Engines Building or running a high-boost, high-powered BMW engine? Boost increases crankcase pressure, which, if left unchecked, can lead to issues such as smoking, power loss, and even engine failure. Adequate venting is essential for optimal performance and engine health. These are designed to connect directly to S58/B58(TU) stock VC, or screw into ANY VTT Billet or Cast VC While some believe a -10AN vent is sufficient for these builds, the truth is: it’s not. To address this, we developed a larger, more effective solution for our builds—now available for everyone. Our Oil Cap adapter securely snaps in place, replacing your oil cap and providing a platform for a -16ORB fitting in a variety of configurations. Choose from -12AN to -20AN fittings, depending on your build’s needs. This cap is thicker than our low-profile option so care must be taken when planning hood clearance for the versatile venting options.
Key Features:
- Attractive Oil cap design
- Connects to stock S58/B58(TU) VC or VTT Billet/Cast VC
- Vented, comes with multi-hole venting to knock down large oil droplets before they make their way into the catch can system
- High-performance venting: Supports configurations from -12AN to -20AN fittings.
- Customizable: Compatible with various fittings to suit your build.
Important Notes:
- This kit requires you to supply your own hose, hose ends, and catch can to complete the system.
- Some fitting options may require 4–5 days for shipping, as we keep only select configurations in stock.
- Also fits other platforms such as B48, B46, Mini, etc. DOES NOT FIT Gen 1 B58
-
Introducing VTT-FAB Billet TIG Trailing Shields VTT-FAB is proud to announce our Billet TIG Trailing Shields, designed to set a new standard in the trailing shield market. We identified a gap where existing options were either too expensive or made from materials that degrade, melt, or fail when exposed to hot surfaces during welding. With this in mind, we took a fresh, innovative approach and developed two high-quality trailing shields to address these issues.
Product Highlights
- Premium Construction: Crafted from billet 6061-T6 aluminum and anodized in red for corrosion resistance and durability.
- Optimal Gas Coverage: Equipped with an internal diffuser and a finely calibrated screen to fully diffuse gas, ensuring optimal coverage for stronger, cleaner welds.
- Versatile Design: Two versions are available:
- Radiused Trailing Shield: Contoured to match 2.5"–5" tubing.
- Flat Trailing Shield: Ideal for flat surfaces and other specific welding needs.
- Universal Compatibility: Suitable for all materials and designed to attach directly to your TIG torch.
- Extremely light: With fittings only 2 Oz for the flat version, and 3 Oz for the radiused!
Innovative Features
- Continuous Argon Flow: Prevents contamination, resulting in cleaner, stronger welds—an essential for TIG welding.
- Swivel Quick Disconnect (QD): Each shield comes with a VTT-FAB Swivel QD Female Connector and a 1/4" Barbed Male Fitting (available in straight or 90-degree options).
- Ensures smooth, tangle-free operation as the swivel moves effortlessly with your hand.
- Allows for quick detachment if you choose not to run gas, enabling you to leave the shield attached to your torch with no line in seconds.
-
High-Boost Crankcase Ventilation Adapter for S58/B58 Engines Building or running a high-boost, high-powered S58 or B58 engine? Boost increases crankcase pressure, which, if left unchecked, can lead to issues such as smoking, power loss, and even engine failure. Adequate venting is essential for optimal performance and engine health. While some believe a -10AN vent is sufficient for these builds, the truth is: it’s not. To address this, we developed a larger, more effective solution for our builds—now available for everyone. Our low-profile adapter securely snaps in place, replacing your oil cap and providing a platform for a -16ORB fitting in a variety of configurations. Choose from -12AN to -20AN fittings, depending on your build’s needs. At just 10mm thick, this adapter maximizes hood clearance for versatile venting options.
Key Features:
- Low-profile design: Only 10mm thick for maximum hood clearance.
- High-performance venting: Supports configurations from -12AN to -20AN fittings.
- Customizable: Compatible with various fittings to suit your build.
Important Notes:
- This kit requires you to supply your own hose, hose ends, and catch can to complete the system.
- Some fitting options may require 4–5 days for shipping, as we keep only select configurations in stock.
- Also fits other platforms such as B48, B46, Mini, etc. DOES NOT FIT Gen 1 B58
-
VTT-FAB is proud to present the finest V-Band heat sinks available on the market. These heat sinks are designed to enhance your welding experience by efficiently dissipating heat away from the V-band flange, thereby minimizing or eliminating warping and pulling.Crafted from 100% billet-machined 6061-T6 aluminum, these V-bands feature precisely machined fins that facilitate rapid heat release. Additionally, they are equipped with dual 1/8" NPT ports on both the top and bottom, with the interior port incorporating a built-in diffuser to ensure optimal gas flow during back purging.Our V-Band heat sinks are available in a range of sizes, including 2", 3.5", 3", and 4", as well as various types to accommodate different V-bands.Features:
- - 100% billet-machined from 6061-T6 aluminum
- - Dual 1/8" NPT ports on top and bottom
- - Built-in diffuser for perfect gas flow during back purging
- - Available in various sizes and styles
SEE BELOW FOR FULL FITMENT SPECS
-
VTT is proud to offer our EWG "Direct Control System" or DCS! This is a completely new innovation for people looking to control the highest-flowing wastegate on the market using an existing BMW electronic actuator. This system will allow BMW owners who have a vehicle with Electronic Wastegates from the factory to utilize this system to control an externally wastegated turbo system, AND it will ALSO allow ANY vehicle to use this setup to control your own custom turbo system. This is done by utilizing our custom 7075 Billet aluminum bracket coupled with a Turbosmart Straight gate, and if needed an EWG controller made for us by DCCD Pro. This allows direct external wastegate control over any turbocharger system with or without EWG for the factory. Features:
- Utilizes the most current wastegate technology the Turbosmart Straight Gate. This gate allows maximum flow with minimal restriction, low drive pressure, and much more. Full details can be found here - https://www.turbosmart.com/product/electronic-straightgate-esg50-external-wastegate/
- Can be configured in multiple ways, and angles based on how you mount the adapter
- The adapter is 7075 Aluminum which has the strength of steel and weight of aluminum
- All connection fittings, are made from Nitronic 60 which has extremely high temperature and wear properties
- Zero Drive Pressure, no springs, no poppet valves, direct control over the gate using factory ECU logic
- Adaptable to ANY turbo system on any car to provide the ultimate in boost control!
-
VTT-FAB Top-Mount Single Turbo Kit
For BMW G8X / F9X S58 Platforms
VTT-FAB is proud to introduce the premiere top-mount single turbo system for the BMW G8X and F9X S58 platforms. Built 100% in-house at our Hayward, CA facility with only the finest components, this kit is engineered to deliver unmatched performance, durability, and simplicity.
At the heart of the system is a hand-fabricated 321 stainless manifold with billet flanges, designed for maximum flow and long-term reliability. Combined with our revolutionary factory-controlled external wastegate system (Turbosmart 60mm Straight Gate), you gain complete boost control directly through your OEM ECU tune — no external boxes, no MAC solenoids, and no extra vacuum/boost lines. Simply reuse your factory actuator with our adapter, and you’re ready for seamless plug-and-play operation with a true boost range from 0 PSI up to the limits of your turbo.
⚠️ Important Notes:
-
If your kit shows out of stock, email [email protected] for current build times.
-
Every VTT-FAB kit is built to order. Once fabrication begins, orders cannot be canceled — please order carefully.
-
-
Looking to keep the underhood heat down on your single turbo car, or build? We got you covered with our VTT-FAB Carbon Fiber Turbo Blankets. The outer shell is made of Carbon Fiber, and the inner shell is Silica Fiber. For 2500F intermittent / 1800 direct heat rating. We have them in 2 sizes T3, and T4. See fitment below Kit included:
- 1 Carbon Blanket of choice
- 2 install springs
-
Are you looking to fab up your own S55 Single kit, but want our game-changing factory control via Turbosmart Straight gate? Yep, we offer that. This manifold is fully fabricated in-house using 321 1.25" Sch 10 Weld els, our own wire cut flange, and cast 6 into 1 Collector. We also fab the Turbosmart straight gate port which will provide perfect fitment for our factory-controlled setup. this manifold is designed to work with T3 V-Band inlets such as Garret G25, G30, G35, PTE T3 Size V-band inlet turbos, and Turbosmart T3 V-Band inlet turbos. This kit will require the use of our VTT-FAB Factory controlled External Straight gate set up, which can be purchased separately, and can be added from the drop-down. Features:
- Fully Fabbed in-house in Hayward Ca using US-sourced parts
- All Tig Welded
- 6 into Cast Collector that fits most T3 Small Frame Style V-band flanges (choose turbo chose from the drop-down)
- Fully set up for our VTT-FAB factory-controlled turbo smart straight gate. Making this plug-and-play with your existing tuner
- 321 Stainless Weld Els for the ultimate in heat resistance and durability
- 1.25" Primary for lightening spool, and high exhaust gas velocity
- Works with VTT-FAB Fitting adapters
THIS IS THE MANIFOLD ONLY! WE DO NOT SELL DOWNPIPES, CHARGE PIPES, ETC. SEPERATELY. THIS WILL REQUIRE YOU TO FAB UP ALL OF THOSE THINGS TO MAKE THIS WORK. IF YOU CANNOT DO THAT WE SUGGEST BUYING THE COMPLETE KIT...
-
VTT is happy to offer custom tig welded 304 Stainless N54/N55 equal-length turbo manifolds. These are perfect for someone trying to fabricate a twin-turbo setup, and needs manifolds. The flange will fit any Garret turbo from GT series, GTX series, and G-Series G25, and G30 V-band.
These are sold as a set of TWO
-
Fabbing up a custom single turbo or twin turbo kit that requires a custom water neck adapter to clear. We got you covered. These are machined from billet 6061-T6 and come in raw aluminum for easy welding.
-
VTT-FAB B58 Factory Control EWG Top Mount Single Turbo kit
For BMW G-Series & Toyota A91 6-Port B58 Platforms
VTT-FAB is proud to offer the premiere top-mount single turbo system for the BMW G-Series and Toyota A91 B58 platforms. This kit is 100% made in the USA at our Hayward, CA facility, using only the highest-quality materials and components.
At the core is a hand-fabricated equal-length 321 stainless steel manifold with billet flanges, designed for maximum flow, durability, and that signature 6-into-1 turbo sound. The system is paired with our factory-controlled external wastegate setup, featuring a Turbosmart 60mm Straight Gate. This innovative design allows full external gate control through the OEM ECU — no additional boxes, MAC solenoids, or vacuum/boost lines required. Simply reuse your factory actuator with our adapter for seamless, plug-and-play control from 0 PSI all the way up to your turbo’s limits.
Unlike other kits, the VTT-FAB system uses no silicone couplers. Instead, we provide VTT-FAB HD clamps to eliminate the risk of blown boost hoses under extreme load.
⚠️ Important Notes:
-
Every VTT-FAB kit is built to order and cannot be canceled once fabrication begins. Please order carefully.
-
If your kit of choice is listed out of stock, email [email protected] for current build times.
-
Garrett turbo options are oil-cooled only (no water lines). This is perfectly fine for street and drag applications. For extended track/road-race use, we recommend adding water cooling
-
-
Sale!
VTT x PFS EBS (External Brushless System) Fuel System
VTT, in collaboration with Performance Fueling Solutions (PFS), is proud to introduce the PFS EBS — External Brushless System.
The EBS is a fully stand-alone, next-generation brushless fuel system available in both platform-specific and universal fitments. Built around state-of-the-art Protec brushless pump technology, this system is capable of supporting up to 2,500 HP on ethanol-based fuels — and even more on gasoline or ethanol blends.
With its compact 15" x 10" footprint and ultra-lightweight construction, the PFS EBS is engineered for performance without compromise. The complete system — including pumps, surge tank, FPR, controllers, and wiring harness — weighs in at under 10 lbs (dry), thanks to a carbon fiber mounting plate and carefully chosen lightweight materials.
EBS Bench Testing Video:
EBS Bench Test Video
