-
PFS B58 Port Injection Kit
$689.99 – $2,299.99Looking for some more fuel for your B58 powered BMW? Not looking to break the bank on overpriced PI kits? PFS has you covered with its Plug, and play PI kit for the B58. -
Do you work on a lot of BMW engines from various platforms? Do you ever struggle with heavy cylinder heads, either lifting off the engine or simply moving around? Ever ruined an EXPENSIVE multi-layer head gasket while trying to install a cylinder head due to no secure way to hold it without two people? We answered yes to all of those things, and came up with a tool for anyone that works on BMWs often, and needs a way to simply, and easily remove/install, or simply move around a cylinder head. These cylinder head tools are machined from a solid billet of 6061-T6 aluminum and anodized in 4 colors for long-lasting corrosion resistance. They are knurled for a non-slip grip when oily or wet, and positioned so the head is balanced when lifting The Head Handler fits the following engines, N54, N55, S55, B58, S58 and we offer short extensions for installation with no cams/Cam ledges on the head, or long extensions for people that want to install or remove a head with cams still installed. (B58 only requires short extensions)
-
VTT noticed a hole in the A9X/Z4 market for a high-quality, lightweight, NVH-friendly, and easy-to-install Diff Lock Down kit to improve diff stability under launching, and hard cornering. So we did something about it and went to work on a very innovative design that 100% positively locks the diff down from movement, while shielding it from adding a ton of NVH, and can be used with the stock diff, and subframe bushings. This design uses existing mounting points on the vehicle, you do NOT have to remove the subframe or the Diff to install. Simply remove 4 diff bolts, drill two holes in the subframe slightly bigger, install two M10 riv-nuts, and install the lockdown, you do not even have to move the exhaust. A typical install can be 15-30 minutes for someone who is experienced working on vehicles, an hour if you like taking it slow. You WILL need a Riv-nut tool to install the Riv-nuts, we provide a link below for what we recommend on Amazon. Features:
- Lightweight 1.5 lbs for the entire lockdown plate
- Uses FOUR connection points on the Diff, and two on the subframe for the ultimate in positive diff location, this will stop all diff movement on launch, saving your guibos, etc
- 100% Billet construction from 6061-T6 aluminum
- Anodized in 4 colors for corrosion resistance, a long-lasting finish, and good looks
- The subframe does NOT have to be removed for installation
- Uses all 12.9 grade hardware
- Does not add excessive NVH
- Positively locks down the diff to eliminate all unwanted movement under launches, acceleration, cornering, etc.
-
Unsure of the state of your CHRA's, whether brand new from a questionable source or rebuilt? DON'T install them without having a proper High-Speed balance done! This is the #1 most critical factor when building a turbocharger, and is even more important for performance turbochargers or small twins that see a LOT of RPM. We use a Turbo Technics VS3 balancer, and balance most units down to under .5G Not all turbos will be able to pass a high-speed balancing test for any number of reasons (usually poor assembly, bent shaft, etc), if they will not pass, we will send you the specs they are in, and as close as we could get them. We then will give you the option to send them back, or we can disassemble, and rebuild them in-house using our other balancing, and assembly tools to ensure a properly built/balanced unit. The service is $79.99 each for most turbos, and we have the capabilities to balance most units. If sending in twins please choose TWO as the quantity
UNITS MUST BE SENT IN WITH NO HOUSINGS, AND IN A CONDITION READY TO BE BALANCED, IF YOU NEED TO SEND IN COMPLETE TURBOS, WE CAN DISASSEMBLE, AND BALANCE FOR YOU, BUT AN EXTRA CHARGE WILL APPLY. IF THE UNITS ARE SENT IN A CONDITION WHERE THEY CAN NOT BE BALANCED WE WILL LET YOU KNOW THE PRICE TO GET THEM TO A STATE WHERE THEY CAN BE
-
The Factory B58 TU Upper Cylinder head hose is plastic and is right in the path of your charge pipe if you lose a connection and it blows off. If this does happen to you it can break the plastic neck emptying your coolant in seconds causing you in the best-case scenario to be stranded, and in the worst-case scenario expensive engine damage. Add some cheap insurance with our Billet Upper Cylinder head hose, this sits right above the plastic water neck. Product Details:
- Plug and play direct factory replacement
- 6061-T6 Billet aluminum with black anodizing for a corrosion-free life
- 7-Ply Silicone in 3 colors
- Cheap insurance against a blown charge pipe which could turn into a blown motor
-
VTT is proud to offer a Phenolic spacer for the BMW B58 platform. When upgrading to an aluminum charge cooler you get the benefit of a better core, and more cooling capacity, but it also comes with the downside of DIRECT heat transfer from the head to the manifold which can cause heat soak and less-than-ideal IAT's even with an upgraded charge cooler. We manufacture these from G11 Expoxy sheet which has great heat and hardness characteristics, and we feel is the ideal material for this application. The thickness is 8mm.
Please note: Longer studs or bolts may be required introducing a phenolic spacer into your system
-
PFS Supra upgraded LPFP Line
$89.99VTT is proud to offer the PFS A90/91 Supra upgraded LPFP line. This line replaces the factory line from the tank to the hard-line under the drivers feet with a line which increases diameter 22%, and volume/area 56% over factory line. The factory line is just under 8mm ID the PFS line uses genuine Parker 801-6 hose which is 10mm ID. This is a plug-and-play option. Remove your factory line, and install this line in its place, it will fit in all the line holders. -
VTT Virtual Gift Card
$50.00 – $1,000.00Please Note: This is a Virtual Gift Card. After purchase you will receive an email with your Gift Card code
-
VTT A90/91 Supra Carbon Fiber Driveshaft
$1,899.00THE DRIVESHAFT for the MK5 Supra! VTT Is proud to offer our Carbon Fiber Driveshaft for the A90/91 Supra made exclusively for us by PST one of the leading names in CF driveshaft technology! This driveshaft is made from 3.25" CF tubing Spicer 1350 Yolks, and U-Joints. All pieces are then bonded using PST's proprietary process, and balanced to within 1/8 In/Ounce. We couple the driveshaft with VTT Custom 7075 aluminum adapters, 4340 Rear end Adapter all which convert the 3-bolt BMW bolt pattern to the 4-bolt Spicer yolk pattern and one heavy-duty CV Joint. ALL OF THE quickest and fastest Supra run this shaft, dont get stuck with a lower-strength broken shaft at the strip. Do it once, do it right for LESS! Made in the U.S.A -
A90/91 Supra / G – Series BMW “GC” Front Drag Brake Kit
$1,219.99 – $1,849.99Looking to make your A90/91 Supra faster in the 1/4 mile or 1/2 mile racing? Want to run 17", (or 15" wheels with suspension modifications), and skinnies in the front? Want to drop OVER 70lbs of unsprung weight off the front of the car at the same time? Do not want to break the bank while doing so? Look no further than the VTT "GC" Front Drag kit for the A90/91 Toyota Supra. This kit will allow you to run the wheel/tire combo you need to drop your ET's all while putting the car on a significant diet over the stock front brake set up. The kit is a true plug-and-play kit using Genuine Wilwood parts, coupled with DOT-approved brake lines, CNC 7075 rotor hats/brackets, and a CEL eliminator harness for the brake sensor. This kit comes in 2 different variations, with two different caliper sizes for each Fits all 2020+ Supra, and some G-Series BMW. We have confirmed fitment on M340iDisclaimer: The HD kits are designed for street use, and drag racing. Never use for heavy braking racing environments such as Auto-X or Road Racing. Scalloped kits should never be used for street driving, and are ONE-PASS COOL DOWN DRAG RACING ONLY, EVEN IN THIS ENVIRONMENT, THEY MAY CRACK IF USED TOO AGGRESSIVELY. Always drive within your limits!
-
Need a Tee fitting for plumbing Vacuum, or Boost lines, Don't want to use cheap plastic ones that can get soft when hard, and brittle after they heat cycle? We didn't either, which is why we machined these high-quality billet tees to solve this issue. Machine from 6061-T6 aluminum, and anodized in black for a long-lasting corrosion-free finish, these tees look great, and will you never have to worry about one failing. We offer them in two sizes, each size has 12mm legs and 3 barbs:
- 7.60mm / -4 Push Lock for people looking to use -4 push lock hose or -4 AN hose. This is a perfect fit for those.
- 1/4" For people looking to use 1/4" vacuum tube
-
B58 CP-CARRILLO FORGED PISTON SET
$1,419.99 – $1,469.99These are the same premium pistons we use in our winning race and high-performance street engines around the world! We feel that these are the best pistons for your high performance or racing engine. -
VTT-FAB Billet Velocity Stack
$39.99 – $49.99Running an open turbo, and want to straight out the airflow to the compressor for extra efficiency. Our billet velocity stack is what you need. Backed by physics a Bellmouth or velocity stack will help smooth the air coming into the turbocharger or on NA cars. These are made from 6061-T6, and anodized in a variety of colors and sizes. Currently, we offer 3", 4", and 5" These are suitable to fit any intake tubing or turbocharger inlet with that size. These are available with or without a silicone connector and clamps. Our V-Stacks are also made to extend down on the outside so you can attach a Vibrant S&B or other compatible 7" Filter on the 3"/4" version. Features:- Smooth air before it enters the turbocharger or Intake
- Very low profile, only sticking 2.5" above the turbocharger inlet. Even if you have no room for a filter these will fit
- Fits all turbochargers with a 3", 4" or 5" inlet including PTE Sportsman Cover!
- 3" and 4" version works with Vibrant #10961 7" filter or S&B 1032 Filter if you have room
- 100% billet construction for high-strength
- Anodized for long life, and durability
-
Sale!
VTT A90/91 Supra Billet Oil Cap
$54.99 – $59.99Want to get rid of the plastic oil cap on your Supra, and add some nice billet pop to your engine bay? Look no further than the VTT Billet Oil cap. These are a true Billet oil cap machined from 6061-T6, and anodized in a variety of colors. These are NOT a thin cap that snaps over your existing oil cap. Currently, we offer them in 4 colors -
Sale!
VTT Billet Large Capacity BMW ZF8HP Transmission Pan
$699.00$599.00VTT is Proud to offer our Billet Aluminum ZF8HP 8-speed Transmission pan. This pan does away with the factory plastic or cast aluminum pan and upgrades it to 6061-T6 aluminum anodized in a variety of colors. This pan increases fluid capacity to 5.7 QTs compared to the stock pan which holds 3.7 QTs, has a US-made reusable Viton Gasket, a rare earth magnet that sits under the filter to not only support it, but pulls metal from the fluid, machined external fins to help aid in cooling, and a -6 ORB magnetic drain plug. Clearance is NOT increased on G8X, X3/4M, or F90 M5, if used on smaller model ZF8HP with the plastic pan, the pan DOES fit but has reduced clearance. Product Features:- Billet construction using 6061-T6 aluminum for long life, and added strength
- Add a full 2 QTs fluid capacity at 5450ML (5.7QTs) compared to 3500ML (3.7QTs)
- Machined fins for improved cooling
- Rare Erath magnet built in to pull metal from the fluid
- US-Made Viton Gasket
- -6 ORB magnetic drain plug for easy service
-
VTT-FAB Extension Harnesses
$45.99 – $99.00Need to move your coolant expansion tank to the other side of the vehicle for a single turbo kit you are building, extend Map sensor plugs, or IAT, how about Throttle Body? Don't cut your factory wires. Just get a VTT-FAB extension harness, and plug and play! These come in various lengths and are covered in expanded sheathing with heat shrink on both ends for a long-lasting, good-looking finish. Available:- Coolant Extension for late model BMW 2015+ 5 ft
- Pre-Throttle Map sensor extension harness 2 ft
- Pre-Throttle IAT Sensor extension harness 2 ft
- B58/S58/B48 etc Throttle body extension harness 2 ft
- B58 to S55 Throttle conversion/extension harness 2 ft
- EWG Actuator Extension harness, Various Lengths
- N54 stock MAP to 3.4 N20 Map sensor extension
-
VTT is proud to offer high-performance drop-in replacement filters for the BMW B58 TU, this includes G series BMW including Z4, A90/91 Toyota Suora, and. These filters are custom-made for VTT. They are made with a heat-resistant silicone base, and a high-flowing cotton weave element with a pre-oiled design to catch contaminates but allow free flow. We designed these to work with our Carbon Fiber intake Tops, but these filters will also work perfectly with the stock tops. We offer them in two colors. Red, and Black Features:
- 50 States Emissions Legal
- Easy to install in 15-30 minutes even for a novice
- Filters can be cleaned forever meaning never buy new filters
- Completely reversible if you ever want to remove
-
VTT 6 Piston Caliper upgrade (Must own 4 piston kit)
$1,049.99 – $1,109.99 -
Sale!
VTT A90/91 Double Adjust Drag Shock Kit
$1,349.99$1,329.99Looking to maximize your A90/91 for drag racing? Want to be able to dial in the perfect amount of compression or rebound on your launch? The VTT Double adjust drag shock kit is just want the doctor ordered! -
B58 CP-CARRILLO CONNECTING ROD, SET (6)
$1,739.99 – $2,209.99Carrillo connecting rods are well known within pro racing and street performance circles for good reason; they produce a premium product that winning racers around the world depend on. -
VTT “DCS” EWG System for TurboSmart Straight Gates
$799.99 – $1,499.99VTT is proud to offer our EWG "Direct Control System" or DCS! This is a completely new innovation for people looking to control the highest-flowing wastegate on the market using an existing BMW electronic actuator. This system will allow BMW owners who have a vehicle with Electronic Wastegates from the factory to utilize this system to control an externally wastegated turbo system, AND it will ALSO allow ANY vehicle to use this setup to control your own custom turbo system. This is done by utilizing our custom 7075 Billet aluminum bracket coupled with a Turbosmart Straight gate, and if needed an EWG controller made for us by DCCD Pro. This allows direct external wastegate control over any turbocharger system with or without EWG for the factory. Features:- Utilizes the most current wastegate technology the Turbosmart Straight Gate. This gate allows maximum flow with minimal restriction, low drive pressure, and much more. Full details can be found here - https://www.turbosmart.com/product/electronic-straightgate-esg50-external-wastegate/
- Can be configured in multiple ways, and angles based on how you mount the adapter
- The adapter is 7075 Aluminum which has the strength of steel and weight of aluminum
- All connection fittings, are made from Nitronic 60 which has extremely high temperature and wear properties
- Zero Drive Pressure, no springs, no poppet valves, direct control over the gate using factory ECU logic
- Adaptable to ANY turbo system on any car to provide the ultimate in boost control!
-
Looking to adapt your wheel bore size to a smaller hub bore? VTT has you covered with our hub-centric adapters. These adapters are made from Billet 6061-T6 aluminum, and anodized in black. We have these sizes currently
- 57.1mm hub to 60.1mm wheel bore
- 57.1mm hub to 64.1mm wheel bore
- 57.1mm hub to 66.1mm wheel bore
- 57.1mm hub to 66.6mm wheel bore
- 57.1mm hub to 67.1mm wheel bore
- 57.1mm hub to 70.3mm wheel bore
- 57.1mm hub to 71.6mm wheel bore
- 57.1mm hub to 72.6mm wheel bore
- 57.1mm hub to 73mm wheel bore
- 57.1mm hub to 74mm wheel bore
- 57.1mm hub to 74.1mm wheel bore
- 64.1mm hub to 72.6mm wheel bore
- 66.6mm hub to 72.6mm wheel bore
They are sold in sets of two, order TWO SETS for a full car, or one set per axle.
-
Sale!
VTT BMW Wireless Plug, and Play Line Lock Kit
$649.00$599.00VTT is proud to offer a truly plug-and-play line lock kit for select BMW vehicles that does NOT require running wiring inside the car, mounted switches, holes in the dash, etc. Our newly designed and released line lock kits use a 40amp wireless remote control switch with 4 different modes that allow you to tailor your line lock setup exactly as you prefer. You simply install the solenoids, install the harness with the switch which has all the wiring terminated, bleed the brakes, and you are ready for effortless burnouts which will not be interfered with by the DME because you are holding the brakes, nor wear your rear brake pads. You can store the remote anywhere in your vehicle, center console, cup holder, door cup holder, etc., and when you need to do a burnout to heat your race tires it's in arm's reach without running any wiring into the vehicle. Fitment is confirmed for G8X M3/4, A9X Supra - The kit itself including lines, solenoids, etc will fit most all late model BMW Chassis including F8X, F3X, G2X, etc. The main concern will be mounting the wireless switch in the passenger cowl area. The kit includes:- Line lock solenoids with weather pack connectors
- Two Parker 90-degree -3 an fittings
- Two Stainless Steel adapter fittings
- Two DOT Approved Stainless Steel brake lines
- One complete wiring harness
- One Remote control switch with TWO remotes
-
Skunk 2 B58 TU Camshafts
$1,545.00Skunk2 Ultra Series Stage 1 Camshafts for Toyota Supra MK5/BMW B58TU /// FEATURES • Billet 8660 Alloy Steel Camshafts • Improved Efficiency/Power • Widest Possible Power Band • Smooth Driveability & Idle • Retains Double VANOS + Valvetronic Functionality -
PTE – Precision Turbochargers
$2,234.49 – $4,428.99VTT is proud to offer PTE Turbocharger products! -
VTT is proud to offer 2020+ Toyota Supra Carbon fiber intake lids. BMW did a wonderful job designing these intakes and we have found they are only slightly restrictive at elevated power levels. With this in mind, we decided to just take their cues, and make a factory-style carbon fiber intake top with a high-flow cotton pre-oiled filter. These are 8 layers of 100% carbon, not a single layer wrapped over plastic, and they are 1.3MM thick with our logo vacuum printed onto the tops, with a UV-resistant gloss clear coating. This is not only strong but will resist discoloration for an extended period of time. The filters themselves are made with a heat-resistant silicone base, a high-flowing cotton weave element with a pre-oiled design to catch contaminates but allow free flow. Filters are available by themselves for a flow upgrade while keeping the stock look here – https://vargasturbo.com/product/vtt-bmw-toyota-b58-tu-high-performance-drop-in-air-filter-upgrade/ Complete CF Lid kit with Silicone intake tube, and billet adapter available here - https://vargasturbo.com/product/vtt-a90-91-supra-modular-silicone-intake-system/
-
Looking to remove your BOV either for leak testing, or dont want to run one, and your charge pipe or housing has a flange on it. You can use this billet plate to block off the BOV flange. Uses the O-ring from the BOV to seal, and removes the BOV. Fitment: Tial BOV Turbosmart BOV with female flange like Tial
-
Looking to protect your single turbo investment, dont have a ton of room, and need a low profile filter that can flow what you need? VTT Has you covered with our Low Profile Single turbo Air Filters. These filters are custom-made for VTT. They are made with a heat-resistant silicone base, and a high-flowing cotton weave element with a pre-oiled design to catch contaminates but allow free flow. We currently offer them in Black, and 3 flange sizes. 3", 4" and 5" flange. With two filter heights. Tested at over 1200WHP with no loss of power observed. Filter Options - Offered in White, and Black with the following dimensions Short - 3.75" Tall, 7.5" OD Large end, 5" Small end 3", 4", or 5" Flange Tall - 4.5" Tall, 7.5" OD Large end, 5" Small end 3", 4", or 5" Flange
-
Sale!
BMW Factory OEM EWG Actuator Replacement – 11 65 8 691 853
$499.00$349.00Looking to replace your damaged factory BMW Actuator part number - 11658691853 VTT has located and ordered in bulk these actuators, and offer them at a discounted price. These are 100% FACTORY BMW OEM actuators, not aftermarket. Fitment is for the following, but they work to replace basically any BMW Actuator. -
VTT Tesla Model 3 / Model Y Billet Wheel Spacers
$54.99 – $69.99VTT is proud to offer billet wheel spacers for most Tesla platforms. These spacers are CNC machined from 6061-T6 aluminum and hard anodized black for a long corrosion-free life. We offer them in the below sizes, which fit many platforms including but not excluded to Model 3, Model Y, Model S, and Model X- 5x114.3 to 5/114.3 64.1 Bore for Model Y, Model 3 - 15mm, 17.5mm, 20mm, and 25mm
- 5X120 TO 5/120 64.1 Bore for Model S, Model X - 15mm, 17.5mm, 20mm, and 25mm
THESE ARE SOLD INDIVIDUALLY, FOR ONE AXLE ORDER TWO, FOR A COMPLETE SET, ORDER FOUR.
YOU MUST ENSURE YOU HAVE CLEARANCE IN YOUR WHEEL TO FIT THE ORIGINAL MOUNTING HOLES AS THEY ARE NOT FLUSH WITH THE SPACER.
PLEASE DOUBLE-CHECK YOUR BOLT PATTERN, AND HUB BORE BEFORE YOU ORDER. INSTALLED SPACERS CANNOT BE RETURNED!
-
VTT Physical Gift Cards
$50.00 – $1,000.00Give the Gift of VTT! Looking to get your friends, or family some go-fast parts, and no idea what they need, only that they love VTT? Well, our Gift Cards have you covered! They come in $50, $100, $250, $500, and $1000 increments. Each gift card is precision cut out of plastic in the shape of the VTT logo and has the dollar amount and the code on the back. Each gift code is unique and is locked to that card. To redeem simply enter the code during check out it will remove that amount, and if you have any leftover it will go back to the card.
You can choose to have your card physically mailed to you, or a virtual card where we can send you a scan of your card.
-
Sale!
TOYOTA B58B30 STROKER KITS
$7,229.99 – $7,559.99VTT Is proud to offer the BC stroker kit for the Toyota B58B30 engine platform that incorporates a 100mm stroke, steel billet crank, BC 4340 Pro Series Heavy-Duty connecting rods rated to 1600+ horsepower.
