-
One Ethanol Racing Fuel
$69.99 – $559.99Please note: Due to heavy increases in freight costs we have had to raise prices by $50 on 54-gallon drums, and $15 on pails.
VTT is proud to be the West Coast dealer for One Ethanol racing fuel.
We have two blends available in 5-gallon pails and 54-gallon drums. See below for descriptions of both fuels
Fuel is available for local pick up only unless you email, and make arrangements for freight shipping. Be aware fuel is considered hazmat and the freight charges are equal to or more than the fuel in all instances. Fuel CANNOT be shipped normal shipping methods such as UPS, FED EX, etc
-
PFS S58 Port Injection Kit
$899.00 – $1,369.99Looking for some more fuel for your S58 powered BMW? Not looking to run Bulky PI plates, and push your TB and charge tract out of alignment? PFS has you covered with its Plug, and play PI kit for the S58. -
Looking to go above 45 psi in your BMW-powered vehicle? Looking for a plug-and-play solution? We have you covered with our BMW 5 bar sensor. These will allow 58 psi to be read and are factory plug, and play. Simply remove your old sensor, replace it with the 5 bar, and have your tuner rescale your map values in both your DME tune and your PI tune if applicable. These are GENUINE BMW sensors directly from BMW.
-
Heat is the enemy of power, and the last thing you want is hot coolant heating your charge air even further right before it enters the charge cooler, but this is what BMW has done on the S58. This is done for emissions and quick warm-up purposes. However, If you are looking to make power on the S58, and are upgrading your charge cooler, or adding PI. While you are there, it takes 30 seconds to remove the coolant lines from the TB connections and replace them with our billet coolant delete kit. This completely removes the coolant from the Throttle body and provides a bypass for the coolant. Simply remove the two lines going to the throttle body, and run our hose in their place. You leave the coolant fittings on the TB open and avoid any unwanted heat being introduced into your charge tract. In our opinion a must for full effort builds. We take the work out of it for you. Kit included:
- One Plug and Play TB Coolant Delete Hose
- Billet 6061 Anodized coolant fittings for long leak-free life
- Reinforced 7-ply silicone hose for strength and longevity
- Vibration-resistant crimp clamps
- 100% plug and play, NO cutting or removing factory clamps or hoses. Fully reversible
-
PFS G8X/F97/98 S58 BMW Drop in Brushless LPFP upgrade (1000WHP+ Capable)
$1,469.99 – $1,679.99PFS is proud to offer a true drop-in 1000WHP+ capable LPFP for G -Series s58, and the F9X X3/4M. This LPFP needs NO additional pumps, wiring harnesses, etc etc. It will support up to 800WHP on Ethanol percentages as high as E98 and will support much higher power levels with less E content as long as you have the octane to support it. For the pump, we start with a factory bucket, we modify it extensively to accept our custom PFS Brushless fuel pump. We then re-terminate the factory wiring to accept the new pump. No wiring splices, done the same way the factory does -the right way.PLEASE NOTE, X3/4M USES A DIFFERENT TOP HAT FOR PRE-LCI, AND LCI. WE HAVE NEW PRE-LCI BUILDS IN STOCK, LCI NEEDS TO SEND YOUR CORE FIRST FOR US TO UPGRADE. CURRENTLY, WE ARE WAITING ON G8X CORES, AND ARE ONLY BUILDING YOUR CORES WITH A 1-3 DAY TURNAROUND.
-
Need a Tee fitting for plumbing Vacuum, or Boost lines, Don't want to use cheap plastic ones that can get soft when hard, and brittle after they heat cycle? We didn't either, which is why we machined these high-quality billet tees to solve this issue. Machine from 6061-T6 aluminum, and anodized in black for a long-lasting corrosion-free finish, these tees look great, and will you never have to worry about one failing. We offer them in two sizes, each size has 12mm legs and 3 barbs:
- 7.60mm / -4 Push Lock for people looking to use -4 push lock hose or -4 AN hose. This is a perfect fit for those.
- 1/4" For people looking to use 1/4" vacuum tube
-
PFS S58 Port Injection Block Off kit
$104.99 – $209.99Looking to return your S58 back to stock, and need a way to close off the ports drilled in the manifold? We got you covered. This kit will bolt into place, allow you to use your existing fuel rail, and insert injector blanks. Or you buy a new rail with the blanks, which will allow you to sell your current PI kit complete. -
VTT “Game Changer” S58 Charge Air Cooler
$3,999.99 – $4,569.00VTT is proud to announce our “Game Changer” charge air cooler for the S58 G8X, and F9X X3/4M platforms! We have completed testing, and any production changes, and are happy to open Pre-orders for the coolers! While the factory charge air cooler is well done, and robust it leaves a lot to be desired on repeated pulls and ends up heat soaked very quickly. Using Proprietary US MADE “WAGNER Intercooler” Cores. We then couple that with CFD-designed runners, and end tanks that we have TIG welded right here in San Leandro California. With this strategy, we are able to take the limited space given to us by the factory, and add not only a larger more efficient core, but also much better designed/flowing runners, and end tanks. We also pack the unit with tons of awesome features, all at a great price! Pricing is as follows:- DI Manifold only - Raw Aluminum - $3999
- PI Manifold with Fuel Rail and PI provisions - Raw Aluminum - $4199
- DI Manifold only - Cerakoted with thermal Dispersion OR custom color - $4369
- PI Manifold With Fuel Rail and PI provisions - Cerakoted with thermal Dispersion OR custom color - $4569
