-
VTT Universal Turbo Fittings – Oil & Coolant Solutions for BMW Turbo Builds!
Looking to fabricate your own turbo kit for BMW platforms? Need an easy solution to block off water lines or create custom feed and drain fittings? Look no further! VTT offers a wide range of high-quality oil and coolant fittings to simplify your build. Our fittings are designed for most late-model BMW platforms, providing a plug-and-play solution for custom turbo setups. 📌 Available Fitting Options: 🔹 Oil Feed – -4 AN Male 🔹 Oil Drain – -10 AN Male 🔹 Coolant Fittings – Barbed Male or Block-Off Options -
Are you building a single kit for the N54, N55, or S55 platform? The stock studs are usually a little bit short for most single-head flanges, and finding M7 studs is not easy. So we made our own longer studs to combat the issue. Made from 10.9 grade steel, and coated in black oxide, these are the perfect solution to the short stud problem. Sold individually so order the number you need. Stud details are as follows
- Overall length 47mm (stock 39mm)
- 3mm shoulder
- 6mm head which is 5mm hex
- 14mm short end
- 24mm long end (stock 15mm)
Dont forget our M7 copper lock nuts as well to complete the job - https://vargasturbo.com/product/vtt-fab-m7-copper-locking-exhaust-nuts/
-
Are you building a single kit for the N54, N55, or S55 platform? M7 Locking exhaust nuts is not easy. So we made our own to combat the issue. These are the perfect solution to the problem of hard-to-find M7 lock nuts. Sold individually so order the number you need.
Note: This is nuts ONLY Stud not included, by our extended M7 studs here - https://vargasturbo.com/product/vtt-fab-extended-m7-n54-n55-s55-b58-2-port-head-studs/
-
WHP Level supported (with proper fuel, upgrades, and tuning) Stock – 425WHP
While we feel this should go without saying—since none of the photos show a turbine housing—just to be absolutely clear:
This product includes the CHRA and compressor housing only.
It is designed to be used with your existing stock turbine housing.Frequently Asked Questions What is included in the N55 Turbo Upgrade Kit?
The N55 Turbo Upgrade Kit includes high-performance components designed to enhance your engine’s power and efficiency. It typically features upgraded turbochargers, supporting hardware, and installation instructions for a seamless upgrade.Will the N55 Turbo Upgrade improve my car’s performance?
Yes, this upgrade is engineered to increase horsepower, torque, and overall responsiveness. It optimizes airflow and boost pressure, providing a noticeable improvement in acceleration and engine efficiency.Is the N55 Turbo Upgrade compatible with my vehicle?
The kit is designed specifically for BMW models equipped with the N55 engine. Please check your vehicle’s year and model compatibility before purchasing to ensure a proper fit.Can I install the N55 Turbo Upgrade myself, or do I need a professional?
While some experienced enthusiasts may install the kit themselves, professional installation is recommended to ensure proper tuning, optimal performance, and warranty compliance.
-
Looking to protect your single turbo investment, dont have a ton of room, and need a low profile filter that can flow what you need? VTT Has you covered with our Low Profile Single turbo Air Filters. These filters are custom-made for VTT. They are made with a heat-resistant silicone base, and a high-flowing cotton weave element with a pre-oiled design to catch contaminates but allow free flow. We currently offer them in Black, and 3 flange sizes. 3", 4" and 5" flange. With two filter heights. Tested at over 1200WHP with no loss of power observed. Filter Options - Offered in White, and Black with the following dimensions Short - 3.75" Tall, 7.5" OD Large end, 5" Small end 3", 4", or 5" Flange Tall - 4.5" Tall, 7.5" OD Large end, 5" Small end 3", 4", or 5" Flange
-
Looking to remove your BOV either for leak testing, or dont want to run one, and your charge pipe or housing has a flange on it. You can use this billet plate to block off the BOV flange. Uses the O-ring from the BOV to seal, and removes the BOV. Fitment: Tial BOV Turbosmart BOV with female flange like Tial
-
VTT is proud to offer its very own Game Changer S55/N55 to B58 Coil conversion kit for the BMW S55/N55 platforms. The 55 series of engines has notoriously had ignition problems with the factory coils, while aftermarket upgrades do exist, they can be bulky. The solution is the BMW B58 ignition coils which are extremely robust and can support well over 1000WHP with no issues. This means a plug-and-play affordable solution that fits like stock, and looks AMAZING doing so! We designed our own 6061-T6 Billet bracket in a plethora of colors including matching shades for every S55/N55 Valve Cover. This means you can mix and match the color of the bracket with coil color, with VC color to truly tailor your engine bay to look exactly how you want it to!
Note: Flash setting changes may be required when installing the conversion kit to ensure the proper function of the B58 coils with S55/N55 DME. This can be found in almost all flashing software settings such as MHD, Bm3, etc.
-
Need a Tee fitting for plumbing Vacuum, or Boost lines, Don't want to use cheap plastic ones that can get soft when hard, and brittle after they heat cycle? We didn't either, which is why we machined these high-quality billet tees to solve this issue. Machine from 6061-T6 aluminum, and anodized in black for a long-lasting corrosion-free finish, these tees look great, and will you never have to worry about one failing. We offer them in two sizes, each size has 12mm legs and 3 barbs:
- 7.60mm / -4 Push Lock for people looking to use -4 push lock hose or -4 AN hose. This is a perfect fit for those.
- 1/4" For people looking to use 1/4" vacuum tube
-
Get rid of the restrictive stock plastic intake on your E-Series N55 powered BMW, and replace it with our 2.5 full flow aluminum intake. This is a MUST when upgrading turbos, or trying to get the most from your stock turbo. Constructed of high-grade aluminum, and powder coated with a very durable gloss black finish this upgrade looks as good as it performs.
-
Looking to up your boost limit on just about any BMW vehicle that runs a 3 or 4-wire BMW map sensor including but not limited to S58, B58, N54, N55, S55, S63, B48, B47, B42, B57, B46? We were too, so we decided to make a very easy plug-and-play kit for 3, and 4-wire BMW map sensors. These kits will allow you to completely replace the 3-wire sensor with one of our sensors, leave your stock 4-wire in place for IAT sensing, and move the power, ground, and sensor signal from the factory sensor to our sensor. These sensors have the proper scaling which will allow your tuner to simply change your map sensor scaling in the tune, and the factory ECU will be able to utilize the sensor voltage with no problem. We are offering these in 5 bar (58 psi), and 6 bar (72 psi), and each comes with a plug-and-play harness, and optional fittings for ease of installation.
Note: For the S58/B58 our Factory style Pre-Throttle map sensor is also 5 bar, and will work fine coupled with the post throttle kit, but the scaling is different, if you want matching Voltages Pre/Post throttle you can run two of these.
A variety of install pics can be found below and - Here
Scaling PDF Links: 5-Bar / 6-Bar
Features include:- Plug and Play harnesses with no wire splicing
- Output wire for connecting a PI or external controller to your post-throttle map sensor for the most stable signal that is not affected by throttle closure
- Different fittings are available for your plumbing needs.
- Can have matching voltage signals for pre/post throttle for ease of tuning, and boost reference
- B58/S58 etc Pre Throttle - 3 Wire Harness (Charge pipe to 1/8" NPT adapter needed, for B58/S58 90 degree adapter needed to provide sensor clearance)
- B58/S58 Post Throttle - 4 Wire Harness (Boost reference will be needed from manifold to sensor)
- F90 M5 Pre/Post Throttle - 4 Wire Harness (May need to repin) (Boost reference will be needed from manifold to sensor)
- Most all other platforms Pre/Post Throttle - 4 Wire Harness (May need to repin) (Boost reference will be needed from manifold to sensor)
- B58
- S58
- S63/ S63TU
- N63
- N54
- S55
- N55
- N20
- B46
- B48
- B57
- B47
-
Looking for Mac solenoids for your build? We got em here at VTT-FAB so you can get everything in one place. We have 3-port, and 4-port in stock!
-
Supported power level: GC Stock-600WHP GC+ Stock-700 WHP Ready to take your N55 to the next level? Don’t want to deal with core charges, long lead times, or restrictive factory housings? Look no further! VTT has you covered with our 100% new casting N55 “GC” and “GC+” turbocharger upgrade. We start by keeping the great design elements of the factory N55 turbo and removing the not-so-great ones such as the small factory inlet area, bearing housing oil structure, thrust bearing, and anything else we saw that could be improved upon. With the basics covered, we stepped it up a level adding proprietary VTT changes, and finished off by having all these parts cast to OE quality. What this means for you is serious N55 power made easy; GCs are a drop in turbocharger upgrade that supports over 600-700 WHP while maintaining factory-like spool and all factory connections including oil, water, downpipe, and charge pipe. Add an aluminum intake, tune, and install kit to ensure your GC/GC+ is working at its best!
-
Unsure of the state of your CHRA's, whether brand new from a questionable source or rebuilt? Don't install them without having a proper High-Speed balance done! This is the #1 most critical factor when building a turbocharger, and is even more important for performance turbochargers or small twins that see a LOT of RPM. We use a Turbo Technics VS3 balancer, and balance most units down to under .5G Not all turbos will be able to pass a high-speed balancing test for any number of reasons (usually poor assembly, bent shaft, etc), if they will not pass, we will send you the specs they are in, and as close as we could get them. We then will give you the option to send them back, or we can disassemble, and rebuild them in-house using our other balancing, and assembly tools to ensure a properly built/balanced unit. The service is for most turbos, and we have the capability to balance most units, NOT ALL. If sending in twins please choose TWO as the quantity
UNITS MUST BE SENT IN WITH NO HOUSINGS, AND IN A CONDITION READY TO BE BALANCED, IF YOU NEED TO SEND IN COMPLETE TURBOS, WE CAN DISASSEMBLE, AND BALANCE FOR YOU, BUT AN EXTRA CHARGE WILL APPLY. IF THE UNITS ARE SENT IN A CONDITION WHERE THEY CAN NOT BE BALANCED WE WILL LET YOU KNOW THE PRICE TO GET THEM TO A STATE WHERE THEY CAN BE
-
VTT Billet Velocity Stack (V-Stack)
3" • 4" • 5" Inlet Sizes
Running an open turbo and want to straighten airflow into the compressor for maximum efficiency? The VTT Billet Velocity Stack is exactly what you need.
Backed by fluid-dynamics principles, a proper bellmouth / velocity stack smooths incoming airflow, reduces turbulence, and improves air entry into the turbocharger—or intake on naturally aspirated applications. Unlike thin, stamped alternatives, our V-Stacks are precision-machined for strength, consistency, and performance.
Each unit is CNC-machined from 6061-T6 billet aluminum and anodized for durability and corrosion resistance. Available in 3", 4", and 5" inlet sizes, these stacks are designed to fit any intake tubing or turbocharger inlet of the corresponding diameter.
-
VTT is proud to offer our EWG "Direct Control System" or DCS! This is a completely new innovation for people looking to control the highest-flowing wastegate on the market using an existing BMW electronic actuator. This system will allow BMW owners who have a vehicle with Electronic Wastegates from the factory to utilize this system to control an externally wastegated turbo system, AND it will ALSO allow ANY vehicle to use this setup to control your own custom turbo system. This is done by utilizing our custom 7075 Billet aluminum bracket coupled with a Turbosmart Straight gate, and if needed an EWG controller made for us by DCCD Pro. This allows direct external wastegate control over any turbocharger system with or without EWG for the factory. Features:
- Utilizes the most current wastegate technology the Turbosmart Straight Gate. This gate allows maximum flow with minimal restriction, low drive pressure, and much more. Full details can be found here - https://www.turbosmart.com/product/electronic-straightgate-esg50-external-wastegate/
- Can be configured in multiple ways, and angles based on how you mount the adapter
- The adapter is 7075 Aluminum which has the strength of steel and weight of aluminum
- All connection fittings, are made from Nitronic 60 which has extremely high temperature and wear properties
- Zero Drive Pressure, no springs, no poppet valves, direct control over the gate using factory ECU logic
- Adaptable to ANY turbo system on any car to provide the ultimate in boost control!
-
Looking to replace your damaged factory BMW Actuator part number - 11658691853 VTT has located and ordered in bulk these actuators, and offer them at a discounted price. These are 100% FACTORY BMW OEM actuators, not aftermarket. Fitment is for the following, but they work to replace basically any BMW Actuator.
-
Please Note: This is a Virtual Gift Card. After purchase you will receive an email with your Gift Card code
-
Glass in your VTT Catch Can broken? If so we have replacements avaialble for $10 each. These are direct replacements for the glass that came with your cans.
-
Looking to keep the underhood heat down on your single turbo car, or build? We got you covered with our VTT-FAB Carbon Fiber Turbo Blankets. The outer shell is made of Carbon Fiber, and the inner shell is Silica Fiber. For 2500F intermittent / 1800 direct heat rating. We have them in 2 sizes T3, and T4. See fitment below Kit included:
- 1 Carbon Blanket of choice
- 2 install springs
-
VTT is happy to offer custom tig welded 304 Stainless N54/N55 equal-length turbo manifolds. These are perfect for someone trying to fabricate a twin-turbo setup, and needs manifolds. The flange will fit any Garret turbo from GT series, GTX series, and G-Series G25, and G30 V-band.
These are sold as a set of TWO
-
VTT is proud to offer PTE Turbocharger products! Please Note: All Precision Turbos have a 2-3 week shipping time
-
Give the Gift of VTT! Looking to get your friends, or family some go-fast parts, and no idea what they need, only that they love VTT? Well, our Gift Cards have you covered! They come in $50, $100, $250, $500, and $1000 increments. Each gift card is precision cut out of plastic in the shape of the VTT logo and has the dollar amount and the code on the back. Each gift code is unique and is locked to that card. To redeem simply enter the code during check out it will remove that amount, and if you have any leftover it will go back to the card.
You can choose to have your card physically mailed to you, or a virtual card where we can send you a scan of your card.
