-
Sale!
VTT S55 / N55 Crank Bolt Capture
$129.00$119.99The VTT S55 crank bolt capture. slips over the head of the crank bolt fully encapsulating it, and locks it to the crank hub, meaning it cannot back out no matter what. -
VTT BILLET BMW N54/N55/S55 Crank Seal Guard
$79.99 – $169.99VTT BILLET BMW N54/55 Crank Seal Guard.
It is a well-known issue on the BMW N54/N55/S55 platforms that your serpentine belt can fail for various reasons, when this happens you have a high chance of the belt getting sucked behind the front damper, and then being pushed past the crank seal into your oil pan. From there it can get sucked into the oil pick up causing total engine failure, even if you do not lose the engine it is a COSTLY repair to remove the sub-frame and drop the oil pan to remove the belt. The best way to combat this is to watch for oil leaks and keep up on your maintenance. BUT Even with those preventative measures, pre-mature belt failure can occur. This crank seal guard installs over your front crank seal and will keep the belt from being sucked in if a belt failure does occur. This is a cheap way to ensure you do not end up having to replace your motor from oil starvation due to an ingested belt. -
Sale!
VTT Billet Check Valves
$24.99 – $29.99VTT CNC Billet check valve that can be used for a variety of uses including a vacuum/boost check valve when removing the stock PCV system, and still wanting to run vacuum to the crankcase. Rated at over 100 psi, with a cracking psi of .25psi. -
VTT Billet CNC oil caps add a nice touch of quality to an otherwise plastic-filled BMW engine bay. We offer these in red, black, blue Purple, gold, and clear anodizing. Made from 6061-T6 aircraft aluminum with stainless steel locking tabs. Fits ALL BMWs with a two-prong locking tab design, including but not limited to. N54, N55, S55, S54, N20, S63, S63TU, M54, B58, N63, S65, S85, M57 DieselTHIS CAP DOES NOT FIT, B58TU, S58, A90/91 SUPRA, THIS ONLY FITS 2 PRONG CAP STYLE
-
VTT Ignition Coil Kits
$159.99 – $209.99VTT is proud to offer ignition coil replacements for the N5X platforms, as well as B5X, and many VAG platforms. We started our quest for coils by contacting multiple coil manufacturing companies, paying for individual coils to be made then putting them through rigorous testing in the USA to ensure they matched or exceeded factory output. Once we were satisfied with the testing, we had the best performing coils made to our colors and specs. We offer these coils as complete sets for the N54, B58/S58, and the VAG platforms in either 4, or 5 cylinders. We also offer upgraded plugs which are highly recommended to change when doing coil replacements These coils come in 3 colors, Red, Black, and Blue, and are not simply an aesthetic upgrade but match or exceed the factory secondary spark energy. The VAG coil, is extremely potent, and the tester was so impressed with it compared to the factory coil, he called it a "BEAST" of a coilNote: To extract maximum performance from VTT coils minor tune changes are required to optimize dwell periods. See recommended Dwell times below
-
A well-known issue with the N54 and early N55 with Hydraulic power steering is the plastic pulley either hitting the subframe or simply breaking on its own. This can cause the belt to be ejected from the pulley, and leave you stranded with no serpentine belt. To top it off, if you continue to run the vehicle with the belt off, you also have a good chance of sucking the belt into the engine through the front seal. Put an end to the dreaded plastic PS pulley issues with our 100% Billet Aluminum PS pulley. We make these from 6061-T6 aluminum and anodize them in one of 4 colors (Black, Red, Blue, and Clear) for a great look, and long-lasting finish. These weigh 11Oz, very close to the weight of a stock pulley, and are lighter than the cast aluminum versions on the market.
-
Sale!
VTT Cold Side Charge Pipe
$89.99 – $119.99Whenever upgrading your N54 we suggest going to a true BOV like a Turbosmart Raceport. This cold side charge pipe allows you to do that while getting rid of the prone to cracking plastic charge pipe, and plastic DV's. If you do want to keep the DV set up, we also offer a DV charge pipe. Also available for N55 with no bungs at all, as the DV is on the turbo. Looking for the Charge Pipe & BOV Combo? Click Here -
NGK 94201 Spark plug set for all S58/B58/48 applications, and ALSO for N54/55 running the new B58 coil upgrade. We recommend these for running 100% e85, and high boost on many BMW applications including N54, N55, S55, if you upgrade to the B58 coils. These are also great maintenance replacements for your S58/B58/48 powered vehicle at a much better price than most. Plugs can be bought as a set of 6. You can add pre-gapping for an additional $25
-
NGK 97506 Pre-Gapped Spark Plug Set
$104.99 – $139.99NGK 95706 Spark plug set required for running 100% e85, and high boost on many BMW application including N54, N55, S55, etc. Plugs can be bought as a set of 6. You can add pre-gapping for an additional $25 -
VTT is proud to offer our billet replacement for the factory plastic Oil filter housing cap. This cap does away with the weak plastic cap, and the need for a special tool for removal, while adding some pop, and color to your engine bay. These oil filter housing caps retain ALL of the factory provisions for the filter basket, including the lower pins which are important for the proper function of pressure bypass, etc. They also have cooling fins to help with oil temps. We also designed these caps to complement our Billet Oil caps, and upcoming Billet Power Steering caps, so all 3 will have the same design. Order all 3 - Oil Cap, Oil Filter housing Cap, and Power steering cap for $175 - 10% savings We offer these caps in 4 colors - Red, Black, Blue, and Clear anodize. The cap has a 19mm hex for easy installation, and removal, and includes a new sealing O-ring, and a small O-ring for the oil filter cage.
-
Replacement Gasket for VTT Valve Covers
$29.99 – $64.99Need to replace the gasket on your VTT Aluminum VC? Simply choose your model from the dropdowns to ensure you get the correct version. -
VTT is proud to offer our billet replacement for the factory plastic Power steering cap. This cap does away with the weak plastic cap, while adding some pop, and color to your engine bay. These Power Steering caps retain ALL of the factory provisions including dipstick, and vent hole We also designed these caps to complement our N5X Billet Oil caps, and N5XBillet Oil filter Caps caps, so all 3 will have the same design. Order all 3 - Oil Cap, Oil Filter housing Cap, and Power steering cap for $175 We offer these caps in 4 colors - Red, Black, Blue, and Clear anodize
-
VTT is proud to offer our billet replacement for the factory plastic Coolant Reservoir cap. This cap does away with the weak plastic cap while adding some pop, and color to your engine bay. These Coolant caps retain ALL of the factory provisions by simply allowing you to snap the factory pressure-relief into the new Billet Cap We also designed these caps to complement our N5X Billet Oil caps, N5XBillet Oil filter housing caps, and Billet Power Steering cap and so all 4 will have the same design. We offer these caps in 4 colors - Red, Black, Blue, and Clear anodize, as well as a choice of custom anodize at a cost of $100 extra.
-
Looking for a little extra clearance on your coolant tank fitting due to relocation for single turbo, forward-facing intake manifold, etc. This 90-degree fitting will allow you to run the hose straight down instead of straight out, and increase your clearance, and routing choices. Made of 6061-T6 and anodized black for a long-lasting finish. Comes with fitting, and 1 clamp.
-
VTT Billet Crankcase Breather replacement filter
$19.99 – $24.99Need a replacement filter for your VTT Billet Crankcase breather? You can order on here. We offer them in 3 heights, low 48mm, medium58mm, and tall 68mm. This is measured from base to top. The filter will include a new clamp. For reference: N54/55 mostly use the low A90 Supra use Medium Most Audi applications can fit a tall, but measure your filter before ordering. -
VTT Billet N54/N55 Vacuum/Boost Adapter
$49.99 – $64.99We are happy to release our BMW B54/N55 (Limited N55 Fitment) vacuum/boost adapter. These go inline with the Throttle Body fitting and provide a full boost/vacuum signal from the manifold. This fitting adds two 1/8NPT bungs to accept any fitting that has 1/8" NPT threads. You can choose options, 1/4" barb, as well as 1/8NPT plugs if you only want one barb, etc. These are perfect for running your PI off manifold pressure which is much more accurate than charge pipe, and they are also great for BOV running the proper size line without having to drill a hole in your manifold. These do space out any sensors etc giving inaccurate readings like some of the other brands do. They are made from 6061-T6 anodized black, with steel plugs, and Blue Anodized barbed fittings. You can choose to order in a few ways. You can choose straight or 90-degree barbs. Adapter alone - $40 Basic kit - 1 Adapter, 1 barb, and one plug, one vacuum cap, and one zip tie $45.00 Dual Barb kit - 1 Adapter, 2 barbs, one vacuum cap, and one zip tie $55.00 -
The stock outlet adapter on the N54/55 is NOTORIOUS for cracking when removing. This Billet replacement ensures no leaks, and no more cracked adapters. Available in 6 colors! Black, Red, Clear, Blue, Purple, Gold
-
VTT is proud to offer a Titanium hardware upgrade for all our Billet and Cast VC's. This will come with M6x30 Ti bolts N54 /N55/S55/B58 Gen 1/ B58 TU it will be an Umbrella head with a 16.3mm head. These bolts weigh half as much as comparable steel hardware and look amazing. Colors to choose from will be Burnt, Black, and Natural (silver)
-
VTT Reinforced Universal Silicone Hoses
$9.99 – $14.99VTT offers silicone hoses in various Push-lock sizes, we use these for our catch can kits, but they are also suitable for coolant, vacuum, boost, etc. Do not use with fuel. We offer: -10 Push Lock 24", and 18" -8 Push Lock 24", and 19.5" -6 Push Lock 24" -
VTA Breather
$39.99Not available for single can external PCV Valve. -
VTT is proud to offer our "OBD-LOCK" OBD port locking tool. This tool is made from billet 6061-T6 aluminum and is designed to completely lock out your OBD port from being accessed. This is useful for people who do not want dealers, techs, etc from accessing their OBD port, and possibly changing a tune, etc. This is also perfect for anti-theft prevention as it will not allow a would-be thief to hook up to the car's OBD port, duplicate a key, etc. The OBD-LOCK cannot be removed without physically destroying the OBD port if you do not have the proper tools. VTT uses 5 types of screw head designs for every 200 OBD-LOCKS made. This means that worldwide only 40 OBD-LOCKS are using the same head design. For each batch of 200, we redesign the screw heads meaning every batch of 200 OBD-LOCKS will use different screw heads and tools. Each OBD-LOCK sent has its head design chosen at random. After Extensive testing, we have found that our OBD lock fits EVERY SINGLE OBD port we have tried, this means it will fit every single OBD port currently on the market from a high-end BMW to a Ford F150 diesel. If you order one, and find it does not fit, PLEASE let us know.
FITMENT: We have TWO versions one for ALL GM vehicles and one for ALL NON-GM Vehicles. Please order the one you
-
VTT-FAB Billet Oil/Coolant Fittings, and block offs
$20.00 – $40.00Looking to fab your own turbo kit for BMW platforms, and need an easy solution to block off water lines, or create feed and drain fittings. Look no further, we offer a wide range of oil/coolant fitting options for most late-model BMW platforms. See the Full description below for a full part number breakdown -
Do you work on a lot of BMW engines from various platforms? Tired of having to adjust universal engine stand plates to fit your engine? Hate not having access to the flywheel end with the engine on the stand? We answered yes to all of those things, we made a tool for anyone that works on BMWs often, and wanted a strong bolt-on engine stand plate that keeps the flywheel end of the engine open! These engine stand plates are machined from a solid billet of 6061-T6 aluminum and anodized in 5 colors for long-lasting corrosion resistance. The engine stand plates currently fit the following engines, N54, N55, S55, B58, S58 with more to come! These are lightweight, and rated for over 1200 lbs! Key Features:
- Lightweight and strong billet 6061-T6, anodized for a long-lasting finish
- Direct bolt on to the intake side motor mount location
- Clears all accessories when installed for easy engine assembly when on stand INCLUDING flywheel or flex plate
- Provisions for location pin, and bar to spin the engine on the stand
-
Sale!
VTT-FAB M7 Copper Locking Exhaust Nuts
$3.00$1.49Are you building a single kit for the N54, N55, or S55 platform? M7 Locking exhaust nuts is not easy. So we made our own to combat the issue. These are the perfect solution to the problem of hard-to-find M7 lock nuts. Sold individually so order the number you need.Note: This is nuts ONLY Stud not included, by our extended M7 studs here - https://vargasturbo.com/product/vtt-fab-extended-m7-n54-n55-s55-b58-2-port-head-studs/
-
This is an easy way to order all 3 VTT Billet engine caps for Valve Cover, Power steering, and Oil Filter Cap. We offer these caps in 4 colors - Red, Black, Blue, and Clear anodize
-
Sale!
VTT S55/N55 EWG BILLET CNC Valve Cover
$1,499.00$1,439.99VTT is proud to announce our S55/N55 EWG Billet Valve cover. We created these for the N/S55 owner who wants to add a great look to their engine bay while also getting rid of the stock plastic valve cover which can crack with higher mileage. These will work with the stock PCV hose or an aftermarket catch can, such as our S55 engine catch can kit. Valve Cover Details:- 100% CNC 6061-T6 Aircraft aluminum construction
- Anodized in a variety of colors
- Lightweight; 9.7 lbs. (compared to 7.9 lbs for a stock cover - only 1.8 lbs difference)
- Gives the end-user variety for setting up their Valve Cover and PCV System
- Only Billet option on the market
- All Ports are fully Baffled to avoid unwanted oil from escaping
-
Looking to make sure all metal contaminates that are possibly in your oil are not circulated? VTT has you covered with our Titanium Magnetic oil drain plugs for BMW, and any other vehicle that uses an M12x1.5 drain plug. This drain plug will capture any ferrous metal particles in your oil, and capture them to be cleaned during your next oil change. It also is stronger than a Steel or Aluminum drain plug, and looks cool! These are made from GR5 Titanium and use a rare earth magnet to capture metal particles in your oil... Kit includes:
- 1 Titanium Drain Plug
- 1 M12 Crush Washer
-
VTT Carbon Fiber Dragy Holder
$19.99 – $49.00Tired of your Dragy flying all over the car as you try to do runs? Tired of low sats or no sats warning due to improper location of the Dragy in the vehicle? Well say goodbye to those issues with our new Carbon Fiber and Plastic Dragy holders. These are made from either 100% Pre-Preg Carbon Fiber, or molded plastic for a perfect fit. The carbon fiber gives it just the right look to add to your performance vehicle! Each holder has dual Suction cups and will stick to any smooth surface. We suggest mounting them in the upper left or right corner of your windshield with a full view of the sky. Dragy holder features- Stop your Dragy from flying off the dash, and having to search for it
- Position your Dragy in the optimal position for the best satellite coverage
- VTT Dragy holder exposes the entire top of the Dragy so nothing is blocking the receiver from the Satellite
- The charging port is not blocked and can be accessed with the cover on
- Choose from REAL Carbon Fiber or Molded Plastic
-
Looking to remove the HPFP or DI system on your N54? This plate will block the vacuum pump and prevent oil leaks. You will need to remove any fuel lines, etc. Kit includes
- Block Plate
-
VTT N54/55 BMW Single Piece Silicone Cold Side Charge Pipe
$104.99 – $439.99VTT is proud to offer the very best charge pipe solution for the BMW E Series N54/55 platforms. This system completely does away with the restrictive, and muli-connection stock charge pipe system, and replaces it with a single 6-ply, Heat Resistant, Wire reinforced silicone charge pipe rated at over 200 psi.FITMENT:
• E Series N54 vehicles 335, 135 (Does not fit Z4, and 5 Series) •E Series N55 vehicles 335, 135 (Does not fit SUV or other models) -
Sale!
VTT BMW Carbon Fiber Driveshaft
$1,899.00 – $1,999.99Why overpay for a custom BMW CF Driveshaft? VTT Is proud to offer our Carbon Fiber Driveshaft for many BMW Models made exclusively for us in the USA by PST one of the leading names n CF driveshaft technology! This driveshaft is made from 3.25" CF tubing Spicer 1350 Yolks, and U-Joints. All pieces are then bonded using PST's proprietary process, and balanced to within 1/8 In/Ounce. We couple the driveshaft with VTT Custom 7075 aluminum adapters which completely eliminate any extra guibos etc. These shafts connect directly to the BMW 3 bolt flange, and our 4340 adapter in the rear to get rid of the screw in the shaft. Made in the U.S.A Each Shaft includes the following- 1 VTT/PST CF Driveshaft with attached VTT 7075 adapters
- 1 VTT 4340 Rear End Adapter
- 1 VTT Billet Adapter installation Tool
- 1 BMW Nut Repair kit
- 6 M8 Rear CV joint bolts (E9X, E46 M3 only)
- 3 M10 Rear flange bolts
- 3 M10 front flange bolts
- 1 Small tube of Loc-tite medium thread locker
-
Sale!Are you building a single kit for the N54, N55, or S55 platform? The stock studs are usually a little bit short for most single-head flanges, and finding M7 studs is not easy. So we made our own longer studs to combat the issue. Made from 10.9 grade steel, and coated in black oxide, these are the perfect solution to the short stud problem. Sold individually so order the number you need. Stud details are as follows
- Overall length 47mm (stock 39mm)
- 3mm shoulder
- 6mm head which is 5mm hex
- 14mm short end
- 24mm long end (stock 15mm)
Dont forget our M7 copper lock nuts as well to complete the job - https://vargasturbo.com/product/vtt-fab-m7-copper-locking-exhaust-nuts/
-
Sale!
CNC N54/N55 Single Flange
$309.99 – $389.99100% CNC flange in mild or SS. This flange will fit all N54's and N55's and comes COMPLETE ready for welding your runners onto it -
VTT- S55 / N55 PCV Delete kit
$94.99 – $379.99Have a problematic PCV on your S55/N55 powered BMW, don't want to pay to replace the entire VC? The VTT PCV delete kit is just what you need. This kit blocks the factory PCV from pulling from the head ports, gets rid of the tear-prone rubber diaphragm, and essentially converts your VC into VTA through the factory front port on the VC. This kit can work stand-alone with the cap, and a -10 ORB plug, can be used to run an extra breather port, or it can be installed with any Catch Can kit that uses the front port of the stock VC. Simply remove the factory cap, take out the diaphragm, screw the plug into the center port, and tap the new cap on with a soft blow hammer or similar. This deletes the PCV and allows you to avoid the issues of a failed diaphragm. Kit Choices- Cap and -10ORB plug only (to be used with an existing catch can or VTA)
- Cap and Catch can kit (recirc or VTA) Complete kit to delete the PCV, and run a catch can (Currently works with S55 only)
- Cap Only (To be used if routing an additional hose from the cap to location or set up of choice, requires your parts to work)
- 1 PCV Cap
- 1 PCV port block off Plug
- 1 -10 ORB Plug
- Optional Catch Can kit
-
Show off your VTT support and get a good laugh from people with our "We Like To Party" License plate bracket. Born from the infamous quote in Talladega nights
-
VTT-FAB Billet Mac Solenoid brackets
$45.99 – $49.99Building a kit using Mac solenoids to control boost? Need an easy way to mount it? VTT-FAB has you covered with our billet Mac Solenoid brackets. Machined from 6061 billet and anodized in 3 colors, these are the perfect way to mount your Mac valve and look good while doing it. Each kit includes:- One Mac Solenoid bracket (3-Port or 4-Port)
- 2 Allen screws to hold the valve to the bracket
- M6 Mounting Bolt
-
We have heard all the stories about fluid all over the engine bay, seen the headbands, socks, sweatbands, and all the fixes people have used and still have issues with their PS reservoir. So we decided to do something about it, and started with a ground-up design that completely fixed all those issues, and added some much-needed features to an old BMW design. Kit Includes:
- 1 PS Reservoir in choice of color
- 2 or 4 fittings
- 2 Hose clamps
- Optional One-Way Breather
-
VTT “GC” S55/N55 to B58 Coil Conversion Kit
From: $319.99VTT is proud to offer its very own Game Changer S55/N55 to B58 Coil conversion kit for the BMW S55/N55 platforms. The 55 series of engines has notoriously had ignition problems with the factory coils, while aftermarket upgrades do exist, they can be bulky. The solution is the BMW B58 ignition coils which are extremely robust and can support well over 1000WHP with no issues. This means a plug-and-play affordable solution that fits like stock, and looks AMAZING doing so! We designed our own 6061-T6 Billet bracket in a plethora of colors including matching shades for every S55/N55 Valve Cover. This means you can mix and match the color of the bracket with coil color, with VC color to truly tailor your engine bay to look exactly how you want it to!Note: Flash setting changes may be required when installing the conversion kit to ensure the proper function of the B58 coils with S55/N55 DME. This can be found in almost all flashing software settings such as MHD, Bm3, etc.
-
Do you work on a lot of BMW engines from various platforms? Do you ever struggle with heavy cylinder heads, either lifting off the engine or simply moving around? Ever ruined an EXPENSIVE multi-layer head gasket while trying to install a cylinder head due to no secure way to hold it without two people? We answered yes to all of those things, and came up with a tool for anyone that works on BMWs often, and needs a way to simply, and easily remove/install, or simply move around a cylinder head. These cylinder head tools are machined from a solid billet of 6061-T6 aluminum and anodized in 4 colors for long-lasting corrosion resistance. They are knurled for a non-slip grip when oily or wet, and positioned so the head is balanced when lifting The Head Handler fits the following engines, N54, N55, S55, B58, S58 and we offer short extensions for installation with no cams/Cam ledges on the head, or long extensions for people that want to install or remove a head with cams still installed. (B58 only requires short extensions)
-
VTT Virtual Gift Card
$50.00 – $1,000.00Please Note: This is a Virtual Gift Card. After purchase you will receive an email with your Gift Card code
-
Need a Tee fitting for plumbing Vacuum, or Boost lines, Don't want to use cheap plastic ones that can get soft when hard, and brittle after they heat cycle? We didn't either, which is why we machined these high-quality billet tees to solve this issue. Machine from 6061-T6 aluminum, and anodized in black for a long-lasting corrosion-free finish, these tees look great, and will you never have to worry about one failing. We offer them in two sizes, each size has 12mm legs and 3 barbs:
- 7.60mm / -4 Push Lock for people looking to use -4 push lock hose or -4 AN hose. This is a perfect fit for those.
- 1/4" For people looking to use 1/4" vacuum tube
-
VTT is Proud to offer our Billet Aluminum DCT Transmission pan. This pan does away with the factory plastic pan and upgrades it to 6061-T6 aluminum anodized in a variety of colors. This pan increases fluid capacity by 80% or almost DOUBLE the stock pan, has a US-made reusable Viton Gasket, a rare earth magnet built in to pull metal from the fluid, machined external fins to help aid in cooling, and a -6 ORB drain plug. Product Features:
- Billet construction using 6061-T6 aluminum for long life, and added strength
- 80% or Almost DOUBLE the factory fluid capacity at 2000ML compared to 1150ML
- Machined fins for improved cooling
- Rare Erath magnet built in to pull metal from the fluid
- US-Made Viton Gasket
- -6 ORB drain plug for easy service
-
Adding a Front-facing manifold to your N54, and need to extend your map sensor harness? We got you covered with our 24" extension harness. High-quality wiring, with seating, and our own 3D printed connectors ensure a perfect fit. Fits all N54, and very early N55, please check your plug connection on your map sensor before ordering
-
VTT E90 Carbon Fiber Headlight Duct
$579.99 – $629.99VTT Carbon Fiber headlight duct for the E90 will complete any racecar or streetcar build helping to get rid of weight and add functionality with a working 6″ velocity stack to run your turbocharger into for optimal flow, and ram air. 100% multi-layer prepreg Carbon Fiber, with a UV resistant clear coat for the ultimate in strength, and durability! We offer them in the following varieties: Passenger side duct with 6″ Velocity stack 3″ hose connection Passenger side duct with 6″ Velocity stack 4″ hose connectionFITMENT: PLEASE NOTE IT FITS ALL E90, AND E91 MODELS INCLUDING M3, ETC. THIS LIGHT HAS NOT BEEN TEST FIT ON AN LCI VEHICLE, AND WE CAN NOT CONFIRM IT FITS LCI. WE CAN ONLY CONFIRM PRE-LCI FITMENT AT THIS TIME.
-
VTT “DCS” EWG System for TurboSmart Straight Gates
$799.99 – $1,499.99VTT is proud to offer our EWG "Direct Control System" or DCS! This is a completely new innovation for people looking to control the highest-flowing wastegate on the market using an existing BMW electronic actuator. This system will allow BMW owners who have a vehicle with Electronic Wastegates from the factory to utilize this system to control an externally wastegated turbo system, AND it will ALSO allow ANY vehicle to use this setup to control your own custom turbo system. This is done by utilizing our custom 7075 Billet aluminum bracket coupled with a Turbosmart Straight gate, and if needed an EWG controller made for us by DCCD Pro. This allows direct external wastegate control over any turbocharger system with or without EWG for the factory. Features:- Utilizes the most current wastegate technology the Turbosmart Straight Gate. This gate allows maximum flow with minimal restriction, low drive pressure, and much more. Full details can be found here - https://www.turbosmart.com/product/electronic-straightgate-esg50-external-wastegate/
- Can be configured in multiple ways, and angles based on how you mount the adapter
- The adapter is 7075 Aluminum which has the strength of steel and weight of aluminum
- All connection fittings, are made from Nitronic 60 which has extremely high temperature and wear properties
- Zero Drive Pressure, no springs, no poppet valves, direct control over the gate using factory ECU logic
- Adaptable to ANY turbo system on any car to provide the ultimate in boost control!
-
VTT-FAB Carbon Fiber Turbo Blanket
$64.99 – $99.00Looking to keep the underhood heat down on your single turbo car, or build? We got you covered with our VTT-FAB Carbon Fiber Turbo Blankets. The outer shell is made of Carbon Fiber, and the inner shell is Silica Fiber. For 2500F intermittent / 1800 direct heat rating. We have them in 2 sizes T3, and T4. See fitment below Kit included:- 1 Carbon Blanket of choice
- 2 install springs
-
VTT is happy to offer custom tig welded 304 Stainless N54/N55 equal-length turbo manifolds. These are perfect for someone trying to fabricate a twin-turbo setup, and needs manifolds. The flange will fit any Garret turbo from GT series, GTX series, and G-Series G25, and G30 V-band.
These are sold as a set of TWO
-
Looking to protect your single turbo investment, dont have a ton of room, and need a low profile filter that can flow what you need? VTT Has you covered with our Low Profile Single turbo Air Filters. These filters are custom-made for VTT. They are made with a heat-resistant silicone base, and a high-flowing cotton weave element with a pre-oiled design to catch contaminates but allow free flow. We currently offer them in Black, and 3 flange sizes. 3", 4" and 5" flange. With two filter heights. Tested at over 1200WHP with no loss of power observed. Filter Options - Offered in White, and Black with the following dimensions Short - 3.75" Tall, 7.5" OD Large end, 5" Small end 3", 4", or 5" Flange Tall - 4.5" Tall, 7.5" OD Large end, 5" Small end 3", 4", or 5" Flange
-
Sale!
BMW Factory OEM EWG Actuator Replacement – 11 65 8 691 853
$499.00$349.00Looking to replace your damaged factory BMW Actuator part number - 11658691853 VTT has located and ordered in bulk these actuators, and offer them at a discounted price. These are 100% FACTORY BMW OEM actuators, not aftermarket. Fitment is for the following, but they work to replace basically any BMW Actuator. -
VTT Crank Hub Install Special!
$2,000.00VTT is happy to announce our Spline lock Crnak Hub special! We are offering COMPLETE crank hub service for N54, N55, And S55 using our Spline Lock hubs for $2000 out the door, this includes all parts, and labor required. The usual turnaround time is 2 days, but we can get them done in one day if early morning drop-off is done. Our shop is in Hayward, CA 94541, and we are currently taking appointments to fill up our calendar through the holidays!If you are interested, please email [email protected] with the words "Crank Hub Appointment" in the title, and we can get back to you with an open time slot ASAP. Thank you!
AGAIN: Once purchased you MUST email [email protected] to schedule an appointment. You CANNOT show up until you have appointment CONFIRMATION.
-
VTT Physical Gift Cards
$50.00 – $1,000.00Give the Gift of VTT! Looking to get your friends, or family some go-fast parts, and no idea what they need, only that they love VTT? Well, our Gift Cards have you covered! They come in $50, $100, $250, $500, and $1000 increments. Each gift card is precision cut out of plastic in the shape of the VTT logo and has the dollar amount and the code on the back. Each gift code is unique and is locked to that card. To redeem simply enter the code during check out it will remove that amount, and if you have any leftover it will go back to the card.
You can choose to have your card physically mailed to you, or a virtual card where we can send you a scan of your card.
