-
Are you building a single kit for the N54, N55, or S55 platform? The stock studs are usually a little bit short for most single-head flanges, and finding M7 studs is not easy. So we made our own longer studs to combat the issue. Made from 10.9 grade steel, and coated in black oxide, these are the perfect solution to the short stud problem. Sold individually so order the number you need. Stud details are as follows
- Overall length 47mm (stock 39mm)
- 3mm shoulder
- 6mm head which is 5mm hex
- 14mm short end
- 24mm long end (stock 15mm)
Dont forget our M7 copper lock nuts as well to complete the job - https://vargasturbo.com/product/vtt-fab-m7-copper-locking-exhaust-nuts/
-
Are you building a single kit for the N54, N55, or S55 platform? M7 Locking exhaust nuts is not easy. So we made our own to combat the issue. These are the perfect solution to the problem of hard-to-find M7 lock nuts. Sold individually so order the number you need.
Note: This is nuts ONLY Stud not included, by our extended M7 studs here - https://vargasturbo.com/product/vtt-fab-extended-m7-n54-n55-s55-b58-2-port-head-studs/
-
WHP Level supported (with proper fuel, upgrades, and tuning) Stock - 500WHP
-
VTT Head Port Block-Off Kit
The VTT Head Port Block-Off Kit is designed to seal the built-in ports in the cylinder head that utilize engine vacuum to clear the low-side PCV system. This factory setup can draw oil into the intake manifold, leading to valve carbon buildup and other unwanted issues.
Kit Includes:
-
6 precision-fit set screws
-
Engine-specific tap
This kit is compatible with N54 engines. Each kit is supplied with the correct tap for your specific engine type.
-
-
Need N54 turbo replacements, don't have full turbo replacements in your budget, like wrenching on your own stuff? If you answered yes to any of those questions, the VTT N54 CHRA replacements are perfect for you!
-
WHP Level supported (with proper fuel, upgrades, and tuning) Stock - 625WHP
-
WHP Level supported (with proper fuel, upgrades, and tuning) Stock - 525WHP
-
WHP Level supported (with proper fuel, upgrades, and tuning) Stock - 675WHP
-
Looking to protect your single turbo investment, dont have a ton of room, and need a low profile filter that can flow what you need? VTT Has you covered with our Low Profile Single turbo Air Filters. These filters are custom-made for VTT. They are made with a heat-resistant silicone base, and a high-flowing cotton weave element with a pre-oiled design to catch contaminates but allow free flow. We currently offer them in Black, and 3 flange sizes. 3", 4" and 5" flange. With two filter heights. Tested at over 1200WHP with no loss of power observed. Filter Options - Offered in White, and Black with the following dimensions Short - 3.75" Tall, 7.5" OD Large end, 5" Small end 3", 4", or 5" Flange Tall - 4.5" Tall, 7.5" OD Large end, 5" Small end 3", 4", or 5" Flange
-
WHP Level supported (with proper fuel, upgrades, and tuning) Stock-850WHP VTT is proud to announce an All-new VTT GC redesign for 2021! The latest in our line of N54 VTT “GC” turbochargers. The GC “F-RB” or Full-Rebrand.
This is an all-new take on the VTT N54 “GC” turbocharger, using 100% new parts throughout that is pure performance. Some of the new groundbreaking features include: All turbine side parts are now fully cast from 310 Stainless Steel for increased temperature resistance, and ultimate corrosion resistance. We also fully redesigned the turbine housing -the F-RB's have a much larger volute as well as a proprietary AR which will dramatically increase flow capacity, helping to eliminate stress on the turbine wheel. Fully redesigned compressor housings which now include V-band OR Hose Barb connection options (while our current stock of hose barb connections last). The CHRA’s are redesigned with new compressor wheels, bullet nuts, and better internal parts. These are new turbochargers from the compressor housing to the bearing housing, to the turbine housing, we had them engineered to fit in the stock N54 location, but provide the full flow of a much larger turbo, and providing a flow increase over the V2 “GC”.
With this all-new design, there is no other 850WHP capable turbocharger option on the market single or twins that can match the spool, ease of fitment, power, reliability, OR price of our GC “F-RB” turbochargers!
-
Building a kit using Mac solenoids to control boost? Need an easy way to mount it? VTT-FAB has you covered with our billet Mac Solenoid brackets. Machined from 6061 billet and anodized in 3 colors, these are the perfect way to mount your Mac valve and look good while doing it. Each kit includes:
- One Mac Solenoid bracket (3-Port or 4-Port)
- 2 Allen screws to hold the valve to the bracket
- M6 Mounting Bolt
-
Looking to remove your BOV either for leak testing, or dont want to run one, and your charge pipe or housing has a flange on it. You can use this billet plate to block off the BOV flange. Uses the O-ring from the BOV to seal, and removes the BOV. Fitment: Tial BOV Turbosmart BOV with female flange like Tial
-
Need a Tee fitting for plumbing Vacuum, or Boost lines, Don't want to use cheap plastic ones that can get soft when hard, and brittle after they heat cycle? We didn't either, which is why we machined these high-quality billet tees to solve this issue. Machine from 6061-T6 aluminum, and anodized in black for a long-lasting corrosion-free finish, these tees look great, and will you never have to worry about one failing. We offer them in two sizes, each size has 12mm legs and 3 barbs:
- 7.60mm / -4 Push Lock for people looking to use -4 push lock hose or -4 AN hose. This is a perfect fit for those.
- 1/4" For people looking to use 1/4" vacuum tube
-
Looking to up your boost limit on just about any BMW vehicle that runs a 3 or 4-wire BMW map sensor including but not limited to S58, B58, N54, N55, S55, S63, B48, B47, B42, B57, B46? We were too, so we decided to make a very easy plug-and-play kit for 3, and 4-wire BMW map sensors. These kits will allow you to completely replace the 3-wire sensor with one of our sensors, leave your stock 4-wire in place for IAT sensing, and move the power, ground, and sensor signal from the factory sensor to our sensor. These sensors have the proper scaling which will allow your tuner to simply change your map sensor scaling in the tune, and the factory ECU will be able to utilize the sensor voltage with no problem. We are offering these in 5 bar (58 psi), and 6 bar (72 psi), and each comes with a plug-and-play harness, and optional fittings for ease of installation.
Note: For the S58/B58 our Factory style Pre-Throttle map sensor is also 5 bar, and will work fine coupled with the post throttle kit, but the scaling is different, if you want matching Voltages Pre/Post throttle you can run two of these.
A variety of install pics can be found below and - Here
Scaling PDF Links: 5-Bar / 6-Bar
Features include:- Plug and Play harnesses with no wire splicing
- Output wire for connecting a PI or external controller to your post-throttle map sensor for the most stable signal that is not affected by throttle closure
- Different fittings are available for your plumbing needs.
- Can have matching voltage signals for pre/post throttle for ease of tuning, and boost reference
- B58/S58 etc Pre Throttle - 3 Wire Harness (Charge pipe to 1/8" NPT adapter needed, for B58/S58 90 degree adapter needed to provide sensor clearance)
- B58/S58 Post Throttle - 4 Wire Harness (Boost reference will be needed from manifold to sensor)
- F90 M5 Pre/Post Throttle - 4 Wire Harness (May need to repin) (Boost reference will be needed from manifold to sensor)
- Most all other platforms Pre/Post Throttle - 4 Wire Harness (May need to repin) (Boost reference will be needed from manifold to sensor)
- B58
- S58
- S63/ S63TU
- N63
- N54
- S55
- N55
- N20
- B46
- B48
- B57
- B47
-
Looking for Mac solenoids for your build? We got em here at VTT-FAB so you can get everything in one place. We have 3-port, and 4-port in stock!
-
Unsure of the state of your CHRA's, whether brand new from a questionable source or rebuilt? Don't install them without having a proper High-Speed balance done! This is the #1 most critical factor when building a turbocharger, and is even more important for performance turbochargers or small twins that see a LOT of RPM. We use a Turbo Technics VS3 balancer, and balance most units down to under .5G Not all turbos will be able to pass a high-speed balancing test for any number of reasons (usually poor assembly, bent shaft, etc), if they will not pass, we will send you the specs they are in, and as close as we could get them. We then will give you the option to send them back, or we can disassemble, and rebuild them in-house using our other balancing, and assembly tools to ensure a properly built/balanced unit. The service is for most turbos, and we have the capability to balance most units, NOT ALL. If sending in twins please choose TWO as the quantity
UNITS MUST BE SENT IN WITH NO HOUSINGS, AND IN A CONDITION READY TO BE BALANCED, IF YOU NEED TO SEND IN COMPLETE TURBOS, WE CAN DISASSEMBLE, AND BALANCE FOR YOU, BUT AN EXTRA CHARGE WILL APPLY. IF THE UNITS ARE SENT IN A CONDITION WHERE THEY CAN NOT BE BALANCED WE WILL LET YOU KNOW THE PRICE TO GET THEM TO A STATE WHERE THEY CAN BE
-
VTT Billet Velocity Stack (V-Stack)
3" • 4" • 5" Inlet Sizes
Running an open turbo and want to straighten airflow into the compressor for maximum efficiency? The VTT Billet Velocity Stack is exactly what you need.
Backed by fluid-dynamics principles, a proper bellmouth / velocity stack smooths incoming airflow, reduces turbulence, and improves air entry into the turbocharger—or intake on naturally aspirated applications. Unlike thin, stamped alternatives, our V-Stacks are precision-machined for strength, consistency, and performance.
Each unit is CNC-machined from 6061-T6 billet aluminum and anodized for durability and corrosion resistance. Available in 3", 4", and 5" inlet sizes, these stacks are designed to fit any intake tubing or turbocharger inlet of the corresponding diameter.
-
We are proud to introduce the latest in our line of N54 turbocharger products the VTT "GC LITE" 2.0 turbochargers.WHP Level supported (with proper fuel, upgrades, and tuning) Stock-700WHP
-
We have a variety of fittings in stock to help you get your turbo system plumbed up! Available are:
- 1/8" NPT to -6 AN Male (Great for water lines, or anywhere you need a small 1/8" NPT to -6 Male AN)
- M14x1.5 to -6 AN Male (Great for water lines on Garrett turbos GT, GTX, and G-Series, or anything that has a metric M14x1.5 thread and you need a -6AN male)
- .035" Turbo feed restrictors. These are for Garrett turbochargers and will fit GT, GTX, and G- Series up to G35
- Garret GT, GTX, and G-Series up to G35 -8 An drain adapter. For those that want a low profile -8 drain for their GT-G-Series Garrett. (Comes with two bolts, and a gasket)
-
All new design for 2018! We are proud to introduce the latest in our line of N54 turbocharger products the VTT "GC" 2.0 turbochargers. This is a new N54 turbocharger from the ground up, using 100% new parts throughout.
-
VTT is proud to offer our EWG "Direct Control System" or DCS! This is a completely new innovation for people looking to control the highest-flowing wastegate on the market using an existing BMW electronic actuator. This system will allow BMW owners who have a vehicle with Electronic Wastegates from the factory to utilize this system to control an externally wastegated turbo system, AND it will ALSO allow ANY vehicle to use this setup to control your own custom turbo system. This is done by utilizing our custom 7075 Billet aluminum bracket coupled with a Turbosmart Straight gate, and if needed an EWG controller made for us by DCCD Pro. This allows direct external wastegate control over any turbocharger system with or without EWG for the factory. Features:
- Utilizes the most current wastegate technology the Turbosmart Straight Gate. This gate allows maximum flow with minimal restriction, low drive pressure, and much more. Full details can be found here - https://www.turbosmart.com/product/electronic-straightgate-esg50-external-wastegate/
- Can be configured in multiple ways, and angles based on how you mount the adapter
- The adapter is 7075 Aluminum which has the strength of steel and weight of aluminum
- All connection fittings, are made from Nitronic 60 which has extremely high temperature and wear properties
- Zero Drive Pressure, no springs, no poppet valves, direct control over the gate using factory ECU logic
- Adaptable to ANY turbo system on any car to provide the ultimate in boost control!
-
Please Note: This is a Virtual Gift Card. After purchase you will receive an email with your Gift Card code
-
Glass in your VTT Catch Can broken? If so we have replacements avaialble for $10 each. These are direct replacements for the glass that came with your cans.
-
Looking to keep the underhood heat down on your single turbo car, or build? We got you covered with our VTT-FAB Carbon Fiber Turbo Blankets. The outer shell is made of Carbon Fiber, and the inner shell is Silica Fiber. For 2500F intermittent / 1800 direct heat rating. We have them in 2 sizes T3, and T4. See fitment below Kit included:
- 1 Carbon Blanket of choice
- 2 install springs
-
VTT is happy to offer custom tig welded 304 Stainless N54/N55 equal-length turbo manifolds. These are perfect for someone trying to fabricate a twin-turbo setup, and needs manifolds. The flange will fit any Garret turbo from GT series, GTX series, and G-Series G25, and G30 V-band.
These are sold as a set of TWO
-
Fabbing up a custom single turbo or twin turbo kit that requires a custom water neck adapter to clear. We got you covered. These are machined from billet 6061-T6 and come in raw aluminum for easy welding.
-
VTT is proud to offer PTE Turbocharger products! Please Note: All Precision Turbos have a 2-3 week shipping time
-
Give the Gift of VTT! Looking to get your friends, or family some go-fast parts, and no idea what they need, only that they love VTT? Well, our Gift Cards have you covered! They come in $50, $100, $250, $500, and $1000 increments. Each gift card is precision cut out of plastic in the shape of the VTT logo and has the dollar amount and the code on the back. Each gift code is unique and is locked to that card. To redeem simply enter the code during check out it will remove that amount, and if you have any leftover it will go back to the card.
You can choose to have your card physically mailed to you, or a virtual card where we can send you a scan of your card.
-
WHP Level supported (with proper fuel, upgrades, and tuning) 500 - 900WHP
