-
Looking to get the most efficient turbocharger operation out of your N54-powered BMW? The best way to do this is to remove all restrictions from the inlet and charge the tract. The factory charge pipe has a very small 1" opening and a poorly designed Y section that couples the two banks into one before entering the intercooler. This VTT N54 Aluminum outlet gets rid of those restrictions and provides a full 1.5" from the turbochargers to a smooth Y transition into a 2.5" outlet to fit most aftermarket intercoolers. Do not be fooled by companies trying to sell you oversized 2" charge pipes, these are not going to pick up any power, and will kill velocity. The smallest diameter you can run while still providing adequate flow is always best for flow velocity and reducing time to TQ.
-
VTT Head Port Block-Off Kit
The VTT Head Port Block-Off Kit is designed to seal the built-in ports in the cylinder head that utilize engine vacuum to clear the low-side PCV system. This factory setup can draw oil into the intake manifold, leading to valve carbon buildup and other unwanted issues.
Kit Includes:
-
6 precision-fit set screws
-
Engine-specific tap
This kit is compatible with N54 engines. Each kit is supplied with the correct tap for your specific engine type.
-
-
Whenever upgrading your N54 we suggest going to a true BOV like a Turbosmart Raceport. This cold side charge pipe allows you to do that while getting rid of the prone to cracking plastic charge pipe, and plastic DV's. If you do want to keep the DV set up, we also offer a DV charge pipe. Also available for N55 with no bungs at all, as the DV is on the turbo. Looking for the Charge Pipe & BOV Combo? Click Here
-
VTT silicone inlets are the premier choice for your N54 inlet needs. Made from high-quality, wire-impregnated silicone, these inlets are a full 6mm thick and can withstand even the harshest underhood conditions.
-
VTT Billet Vacuum Canisters
VTT is proud to offer our billet replacement for the factory plastic vacuum tanks that store vacuum from the pump and regulate boost via the solenoids.
The OEM plastic cans – and their small plastic nipples – are known to crack over time. When they fail, you’ll experience low boost, no boost, or inconsistent performance. Our billet cans eliminate this weak link while adding strength, durability, and a pop of color to your engine bay.
Key Features
-
Direct Replacement: Retains all factory provisions, including mounting points.
-
Upgraded Fittings: Includes billet 90-degree barbed fittings for cleaner, easier vacuum line routing.
-
Premium Construction: CNC-machined from 6061-T6 aluminum, anodized for beauty and long service life.
-
Distinct Look: Knurled finish adds a high-end, motorsport-inspired aesthetic.
-
Matching Lineup: Designed to complement the full VTT N54 billet accessory line – oil caps, oil filter housing caps, coolant cap, valve cover, oil cooler block-off plate, power steering cap, and more.
-
-
A plug and play BOV option for your N54. This kit comes with everything you will need to replace your undersized factory DV with a high quality Turbosmart Race port.
-
We are happy to release our BMW B54/N55 (Limited N55 Fitment) vacuum/boost adapter. These go inline with the Throttle Body fitting and provide a full boost/vacuum signal from the manifold. This fitting adds two 1/8NPT bungs to accept any fitting that has 1/8" NPT threads. You can choose options, 1/4" barb, as well as 1/8NPT plugs if you only want one barb, etc. These are perfect for running your PI off manifold pressure which is much more accurate than charge pipe, and they are also great for BOV running the proper size line without having to drill a hole in your manifold. These do space out any sensors etc giving inaccurate readings like some of the other brands do. They are made from 6061-T6 anodized black, with steel plugs, and Blue Anodized barbed fittings. You can choose to order in a few ways. You can choose straight or 90-degree barbs. Adapter alone Basic kit - 1 Adapter, 1 barb, and one plug, one vacuum cap, and one zip tie Dual Barb kit - 1 Adapter, 2 barbs, one vacuum cap, and one zip tie
-
Sale!Save 15% on your VTT Silicone inlets, and aluminum outlets if you order them together!
-
Looking to protect your single turbo investment, dont have a ton of room, and need a low profile filter that can flow what you need? VTT Has you covered with our Low Profile Single turbo Air Filters. These filters are custom-made for VTT. They are made with a heat-resistant silicone base, and a high-flowing cotton weave element with a pre-oiled design to catch contaminates but allow free flow. We currently offer them in Black, and 3 flange sizes. 3", 4" and 5" flange. With two filter heights. Tested at over 1200WHP with no loss of power observed. Filter Options - Offered in White, and Black with the following dimensions Short - 3.75" Tall, 7.5" OD Large end, 5" Small end 3", 4", or 5" Flange Tall - 4.5" Tall, 7.5" OD Large end, 5" Small end 3", 4", or 5" Flange
-
Need a Tee fitting for plumbing Vacuum, or Boost lines, Don't want to use cheap plastic ones that can get soft when hard, and brittle after they heat cycle? We didn't either, which is why we machined these high-quality billet tees to solve this issue. Machine from 6061-T6 aluminum, and anodized in black for a long-lasting corrosion-free finish, these tees look great, and will you never have to worry about one failing. We offer them in two sizes, each size has 12mm legs and 3 barbs:
- 7.60mm / -4 Push Lock for people looking to use -4 push lock hose or -4 AN hose. This is a perfect fit for those.
- 1/4" For people looking to use 1/4" vacuum tube
-
VTT is proud to offer the very best charge pipe solution for the BMW E Series N54/55 platforms. This system completely does away with the restrictive, and muli-connection stock charge pipe system, and replaces it with a single 6-ply, Heat Resistant, Wire reinforced silicone charge pipe rated at over 200 psi.
FITMENT:
• E Series N54 vehicles 335, 135 (Does not fit Z4, and 5 Series) •E Series N55 vehicles 335, 135 (Does not fit SUV or other models) -
If running a Tial BOV on your N54 instead of the TurboSmart Raceport you want to run the black spring. This will provide you with the most complete vent, and eliminate any chance for flutter/surge.
-
Looking to up your boost limit on just about any BMW vehicle that runs a 3 or 4-wire BMW map sensor including but not limited to S58, B58, N54, N55, S55, S63, B48, B47, B42, B57, B46? We were too, so we decided to make a very easy plug-and-play kit for 3, and 4-wire BMW map sensors. These kits will allow you to completely replace the 3-wire sensor with one of our sensors, leave your stock 4-wire in place for IAT sensing, and move the power, ground, and sensor signal from the factory sensor to our sensor. These sensors have the proper scaling which will allow your tuner to simply change your map sensor scaling in the tune, and the factory ECU will be able to utilize the sensor voltage with no problem. We are offering these in 5 bar (58 psi), and 6 bar (72 psi), and each comes with a plug-and-play harness, and optional fittings for ease of installation.
Note: For the S58/B58 our Factory style Pre-Throttle map sensor is also 5 bar, and will work fine coupled with the post throttle kit, but the scaling is different, if you want matching Voltages Pre/Post throttle you can run two of these.
A variety of install pics can be found below and - Here
Scaling PDF Links: 5-Bar / 6-Bar
Features include:- Plug and Play harnesses with no wire splicing
- Output wire for connecting a PI or external controller to your post-throttle map sensor for the most stable signal that is not affected by throttle closure
- Different fittings are available for your plumbing needs.
- Can have matching voltage signals for pre/post throttle for ease of tuning, and boost reference
- B58/S58 etc Pre Throttle - 3 Wire Harness (Charge pipe to 1/8" NPT adapter needed, for B58/S58 90 degree adapter needed to provide sensor clearance)
- B58/S58 Post Throttle - 4 Wire Harness (Boost reference will be needed from manifold to sensor)
- F90 M5 Pre/Post Throttle - 4 Wire Harness (May need to repin) (Boost reference will be needed from manifold to sensor)
- Most all other platforms Pre/Post Throttle - 4 Wire Harness (May need to repin) (Boost reference will be needed from manifold to sensor)
- B58
- S58
- S63/ S63TU
- N63
- N54
- S55
- N55
- N20
- B46
- B48
- B57
- B47
-
VTT N54 Billet Center Feed Intake Manifold
VTT is proud to introduce our ground-up engineered N54 Billet Center Feed Intake Manifold—not a rebadged sheet metal clone like others on the market. This is a purpose-built manifold designed for performance, utility, and seamless integration.
Through advanced CAE/Multiphysics simulations under both steady and unsteady state conditions, we’ve delivered a manifold that not only outflows the OEM unit but also installs with zero compromises. No need for custom charge pipes or modified throttle body harnesses—bolt it on and go.
Real-world testing on a 570WHP stock-motor F-RB Lite turbo car yielded 20–30WHP gains with no tuning changes, especially at the top of the RPM range—where it counts most. Expect even greater results with ported heads, high-lift cams, or higher-output builds.
-
VTT Cone Filters feature High flow elements with a silicone body and a velocity stack built-in for smooth flow. We offer these filters in a variety of sizes for universal use. These are also replacement filters for VTT intake kits including B58 Gen 1, TU, Supra, Audi 4.0, N54 Dual Cone filter kit, etc Kit Includes:
- 1 - Cone Filter
- 1 - Clamp
-
VTT Carbon Fiber headlight duct for the E90 will complete any racecar or streetcar build helping to get rid of weight and add functionality with a working 6″ velocity stack to run your turbocharger into for optimal flow, and ram air. 100% multi-layer prepreg Carbon Fiber, with a UV resistant clear coat for the ultimate in strength, and durability! We offer them in the following varieties: Passenger side duct with 6″ Velocity stack 3″ hose connection Passenger side duct with 6″ Velocity stack 4″ hose connection
FITMENT: PLEASE NOTE IT FITS ALL E90, AND E91 MODELS INCLUDING M3, ETC. THIS LIGHT HAS NOT BEEN TEST FIT ON AN LCI VEHICLE, AND WE CAN NOT CONFIRM IT FITS LCI. WE CAN ONLY CONFIRM PRE-LCI FITMENT AT THIS TIME.
-
Please Note: This is a Virtual Gift Card. After purchase you will receive an email with your Gift Card code
-
Adding a Front-facing manifold to your N54, and need to extend your map sensor harness? We got you covered with our 24" extension harness. High-quality wiring, with seating, and our own 3D printed connectors ensure a perfect fit. Fits all N54, and very early N55, please check your plug connection on your map sensor before ordering
-
Glass in your VTT Catch Can broken? If so we have replacements avaialble for $10 each. These are direct replacements for the glass that came with your cans.
