-
VTT is proud to offer our billet replacement for the factory plastic Coolant Reservoir cap. This cap does away with the weak plastic cap while adding some pop, and color to your engine bay. These Coolant caps retain ALL of the factory provisions by simply allowing you to snap the factory pressure-relief into the new Billet Cap We also designed these caps to complement our N5X Billet Oil caps, N5XBillet Oil filter housing caps, and Billet Power Steering cap and so all 4 will have the same design. We offer these caps in 4 colors - Red, Black, Blue, and Clear anodize, as well as a choice of custom anodize at a cost of $100 extra.
-
VTT is proud to offer our billet replacement for the factory plastic Power steering cap. This cap does away with the weak plastic cap, while adding some pop, and color to your engine bay. These Power Steering caps retain ALL of the factory provisions including dipstick, and vent hole We also designed these caps to complement our N5X Billet Oil caps, and N5XBillet Oil filter Caps caps, so all 3 will have the same design. Order all 3 - Oil Cap, Oil Filter housing Cap, and Power steering cap for $175 We offer these caps in 4 colors - Red, Black, Blue, and Clear anodize
-
VTT N54, N55, S55, N20, B58 Billet Motor Mount Inserts
$169.99 – $449.99 -
Looking for a little extra clearance on your coolant tank fitting due to relocation for single turbo, forward-facing intake manifold, etc. This 90-degree fitting will allow you to run the hose straight down instead of straight out, and increase your clearance, and routing choices. Made of 6061-T6 and anodized black for a long-lasting finish. Comes with fitting, and 1 clamp.
-
VTT Billet Crankcase Breather replacement filter
$19.99 – $24.99Need a replacement filter for your VTT Billet Crankcase breather? You can order on here. We offer them in 3 heights, low 48mm, medium58mm, and tall 68mm. This is measured from base to top. The filter will include a new clamp. For reference: N54/55 mostly use the low A90 Supra use Medium Most Audi applications can fit a tall, but measure your filter before ordering. -
VTT Billet N54/N55 Vacuum/Boost Adapter
$49.99 – $64.99We are happy to release our BMW B54/N55 (Limited N55 Fitment) vacuum/boost adapter. These go inline with the Throttle Body fitting and provide a full boost/vacuum signal from the manifold. This fitting adds two 1/8NPT bungs to accept any fitting that has 1/8" NPT threads. You can choose options, 1/4" barb, as well as 1/8NPT plugs if you only want one barb, etc. These are perfect for running your PI off manifold pressure which is much more accurate than charge pipe, and they are also great for BOV running the proper size line without having to drill a hole in your manifold. These do space out any sensors etc giving inaccurate readings like some of the other brands do. They are made from 6061-T6 anodized black, with steel plugs, and Blue Anodized barbed fittings. You can choose to order in a few ways. You can choose straight or 90-degree barbs. Adapter alone - $40 Basic kit - 1 Adapter, 1 barb, and one plug, one vacuum cap, and one zip tie $45.00 Dual Barb kit - 1 Adapter, 2 barbs, one vacuum cap, and one zip tie $55.00 -
VTT is proud to offer a Titanium hardware upgrade for all our Billet and Cast VC's. This will come with M6x30 Ti bolts N54 /N55/S55/B58 Gen 1/ B58 TU it will be an Umbrella head with a 16.3mm head. These bolts weigh half as much as comparable steel hardware and look amazing. Colors to choose from will be Burnt, Black, and Natural (silver)
-
The stock outlet adapter on the N54/55 is NOTORIOUS for cracking when removing. This Billet replacement ensures no leaks, and no more cracked adapters. Available in 6 colors! Black, Red, Clear, Blue, Purple, Gold
-
VTT is proud to offer our billet replacement for the factory plastic vacuum tanks that store vacuum from the pump and use it to regulate boost via the solenoids. The stock plastic can, and small plastic nipples on the stock cans have a tendency to crank over time, and if they leak you will get low boost, or no boost, and poor performance. These cans do away with the weak plastic cans while adding some pop, and color to your engine bay. These vacuum cans retain ALL of the factory provisions including mounting points but come with 90-degree fittings for easier routing of the lines We also designed these cans to complement our N54 Billet lineup - N5X Billet Oil caps, N5XBillet Oil filter housing caps, Billet coolant cap, Billet valve cover, billet oil cooler block off plate, and Billet Power Steering cap and so on. All will have matching color We offer these cans in 4 colors - Red, Black, Blue, and Clear anodize
-
VTT is proud to offer our "OBD-LOCK" OBD port locking tool. This tool is made from billet 6061-T6 aluminum and is designed to completely lock out your OBD port from being accessed. This is useful for people who do not want dealers, techs, etc from accessing their OBD port, and possibly changing a tune, etc. This is also perfect for anti-theft prevention as it will not allow a would-be thief to hook up to the car's OBD port, duplicate a key, etc. The OBD-LOCK cannot be removed without physically destroying the OBD port if you do not have the proper tools. VTT uses 5 types of screw head designs for every 200 OBD-LOCKS made. This means that worldwide only 40 OBD-LOCKS are using the same head design. For each batch of 200, we redesign the screw heads meaning every batch of 200 OBD-LOCKS will use different screw heads and tools. Each OBD-LOCK sent has its head design chosen at random. After Extensive testing, we have found that our OBD lock fits EVERY SINGLE OBD port we have tried, this means it will fit every single OBD port currently on the market from a high-end BMW to a Ford F150 diesel. If you order one, and find it does not fit, PLEASE let us know.
FITMENT: We have TWO versions one for ALL GM vehicles and one for ALL NON-GM Vehicles. Please order the one you
-
VTA Breather
$39.99Not available for single can external PCV Valve. -
VTT Reinforced Universal Silicone Hoses
$9.99 – $14.99VTT offers silicone hoses in various Push-lock sizes, we use these for our catch can kits, but they are also suitable for coolant, vacuum, boost, etc. Do not use with fuel. We offer: -10 Push Lock 24", and 18" -8 Push Lock 24", and 19.5" -6 Push Lock 24" -
Sale!
VTT External PCV Adapter fitting
$99.99 – $129.99Adapter fitting that is required to convert your N54 to external PCV if you want to keep your crankcase under vacuum at idle, and anytime you have a vacuum condition in your intake manifold. -
Sale!
VTT PCV Flapper delete
$58.00$54.99Made of 6061-T6 aircraft aluminum anodized black, comes with O-ring, and stainless steel holding clip -
Sale!
VTT-FAB M7 Copper Locking Exhaust Nuts
$3.00$1.49Are you building a single kit for the N54, N55, or S55 platform? M7 Locking exhaust nuts is not easy. So we made our own to combat the issue. These are the perfect solution to the problem of hard-to-find M7 lock nuts. Sold individually so order the number you need.Note: This is nuts ONLY Stud not included, by our extended M7 studs here - https://vargasturbo.com/product/vtt-fab-extended-m7-n54-n55-s55-b58-2-port-head-studs/
-
Do you work on a lot of BMW engines from various platforms? Tired of having to adjust universal engine stand plates to fit your engine? Hate not having access to the flywheel end with the engine on the stand? We answered yes to all of those things, we made a tool for anyone that works on BMWs often, and wanted a strong bolt-on engine stand plate that keeps the flywheel end of the engine open! These engine stand plates are machined from a solid billet of 6061-T6 aluminum and anodized in 5 colors for long-lasting corrosion resistance. The engine stand plates currently fit the following engines, N54, N55, S55, B58, S58 with more to come! These are lightweight, and rated for over 1200 lbs! Key Features:
- Lightweight and strong billet 6061-T6, anodized for a long-lasting finish
- Direct bolt on to the intake side motor mount location
- Clears all accessories when installed for easy engine assembly when on stand INCLUDING flywheel or flex plate
- Provisions for location pin, and bar to spin the engine on the stand
-
This is an easy way to order all 3 VTT Billet engine caps for Valve Cover, Power steering, and Oil Filter Cap. We offer these caps in 4 colors - Red, Black, Blue, and Clear anodize
-
VTT Modular BILLET CNC Valve Cover
$1,379.99VTT is proud to announce a ground-up system designed to give the end user complete control over their valve cover/ PCV setup. Tired of being told you will run two -10 lines from your VC to your Catch Can? So were we. Now you can run them any way you want, including complete VTA, oil cap one-way breather, etc. Nothing on the market comes close to the versatility of this setup, and it truly is the ULTIMATE Valve cover, PCV combo, or Valve cover, or PCV setup. You choose how many or how few you want to run. Valve Cover Details:- 100% CNC 6061-T6 Aircraft aluminum construction
- Anodized in a variety of colors
- Lightweight; 9.7 lbs. (compared to 7.9 lbs for a stock cover - only 1.8 lbs difference)
- Gives the end-user true variety for setting up their Valve Cover and PCV System
- Lower pricing than other non-modular options on the market
- All Ports are fully Baffled to avoid unwanted oil from escaping
-
VTT/FF N54 Intake Manifold
$1,429.99THE FAB FACTORY MANIFOLD IS BACK at VTT!
-
Looking to make sure all metal contaminates that are possibly in your oil are not circulated? VTT has you covered with our Titanium Magnetic oil drain plugs for BMW, and any other vehicle that uses an M12x1.5 drain plug. This drain plug will capture any ferrous metal particles in your oil, and capture them to be cleaned during your next oil change. It also is stronger than a Steel or Aluminum drain plug, and looks cool! These are made from GR5 Titanium and use a rare earth magnet to capture metal particles in your oil... Kit includes:
- 1 Titanium Drain Plug
- 1 M12 Crush Washer
-
Looking to remove the HPFP or DI system on your N54? This plate will block the vacuum pump and prevent oil leaks. You will need to remove any fuel lines, etc. Kit includes
- Block Plate
-
VTT Carbon Fiber Dragy Holder
$19.99 – $49.00Tired of your Dragy flying all over the car as you try to do runs? Tired of low sats or no sats warning due to improper location of the Dragy in the vehicle? Well say goodbye to those issues with our new Carbon Fiber and Plastic Dragy holders. These are made from either 100% Pre-Preg Carbon Fiber, or molded plastic for a perfect fit. The carbon fiber gives it just the right look to add to your performance vehicle! Each holder has dual Suction cups and will stick to any smooth surface. We suggest mounting them in the upper left or right corner of your windshield with a full view of the sky. Dragy holder features- Stop your Dragy from flying off the dash, and having to search for it
- Position your Dragy in the optimal position for the best satellite coverage
- VTT Dragy holder exposes the entire top of the Dragy so nothing is blocking the receiver from the Satellite
- The charging port is not blocked and can be accessed with the cover on
- Choose from REAL Carbon Fiber or Molded Plastic
-
Sale!Are you building a single kit for the N54, N55, or S55 platform? The stock studs are usually a little bit short for most single-head flanges, and finding M7 studs is not easy. So we made our own longer studs to combat the issue. Made from 10.9 grade steel, and coated in black oxide, these are the perfect solution to the short stud problem. Sold individually so order the number you need. Stud details are as follows
- Overall length 47mm (stock 39mm)
- 3mm shoulder
- 6mm head which is 5mm hex
- 14mm short end
- 24mm long end (stock 15mm)
Dont forget our M7 copper lock nuts as well to complete the job - https://vargasturbo.com/product/vtt-fab-m7-copper-locking-exhaust-nuts/
-
VTT N54 “DI Injector” Delete Kit
$319.99Looking to get rid of the troublesome and expensive DI injectors on your BMW N54 and move to PI only and a standalone? If so VTT has you covered with its new N54 PI delete kit. This kit allows you to SAFELY remove the DI injectors, install our delete fittings, and run PI only. We machined these deletes from 310 Stainless for extreme heat, and corrosion resistance, and include 3 hold downs. These DI deletes COMPLETELY get rid of all factory provisions, including the seal. If the seal is left intact with no fuel to cool the injector or delete it will quickly overheat and melt the delicate seal causing combustion gasses to escape the engine creating misfires, and worse possibly damaging your injector bore on the cylinder head. Our deletes are machined to be a press fit into the cylinder, and can be either cooled with liquid nitrogen, and dropped in, or tapped in with a hammer, and then held down with the included hold downs. We also include M6 tapped holes on the top of each one in case they need to be removed you can attach a slide hammer, and remove the delete. These are sold as a kit and come with the following- 6 - 310 Stainless DI Delete fittings
- 3 - Hold down brackets
EXTREME ENGINE MODS ARE REQUIRED TO RUN THIS KIT, PLEASE SEE BELOW
-
VTT N54/55 BMW Single Piece Silicone Cold Side Charge Pipe
$104.99 – $439.99VTT is proud to offer the very best charge pipe solution for the BMW E Series N54/55 platforms. This system completely does away with the restrictive, and muli-connection stock charge pipe system, and replaces it with a single 6-ply, Heat Resistant, Wire reinforced silicone charge pipe rated at over 200 psi.FITMENT:
• E Series N54 vehicles 335, 135 (Does not fit Z4, and 5 Series) •E Series N55 vehicles 335, 135 (Does not fit SUV or other models) -
VTT N54 Stock Style Coil Hold Down Kit
$104.99 – $159.99Tire of sloppy coil placement with your stock N54 VC? Upgraded to a VTT Cast or Billet VC, and want to run the stock style coils, while positively securing the coils to the plug? We got you covered with our N54 stock style coil hold-down bracket. This kit uses our N54 to B58 coil conversion bracket, with 6 billet S brackets to securely hold your stock style coils in place. This will eliminate any possible misfire issues from coils being raised off the plug, etc. It also looks badass, and can be ordered in all colors to match your existing setup, including Carbon Fiber! -
VTT is proud to release our very own center feed N54 intake manifold. This is NOT the SAME sheet metal manifold everyone is selling with a different logo on it, this is a ground-up design focusing on utility as well as increased flow capability. We performed CAE/Multiphysics simulation for both steady and unsteady state operating conditions in order to bring real-world performance benefits to your N54 build. Our manifold is stronger, outflows the OEM manifold, and installs just as easily as your stock piece (no custom charge pipe or throttle body harness required). Performance gains of 20-30WHP+ were had with no tune changes on a 570WHP stock motor F-RB lite turbo car at the top of the RPM range where it matters most for performance. These numbers will only increase with ported heads, high lift cams, or even higher horsepower builds!
-
Sale!
VTT BMW Carbon Fiber Driveshaft
$1,899.00 – $1,999.99Why overpay for a custom BMW CF Driveshaft? VTT Is proud to offer our Carbon Fiber Driveshaft for many BMW Models made exclusively for us in the USA by PST one of the leading names n CF driveshaft technology! This driveshaft is made from 3.25" CF tubing Spicer 1350 Yolks, and U-Joints. All pieces are then bonded using PST's proprietary process, and balanced to within 1/8 In/Ounce. We couple the driveshaft with VTT Custom 7075 aluminum adapters which completely eliminate any extra guibos etc. These shafts connect directly to the BMW 3 bolt flange, and our 4340 adapter in the rear to get rid of the screw in the shaft. Made in the U.S.A Each Shaft includes the following- 1 VTT/PST CF Driveshaft with attached VTT 7075 adapters
- 1 VTT 4340 Rear End Adapter
- 1 VTT Billet Adapter installation Tool
- 1 BMW Nut Repair kit
- 6 M8 Rear CV joint bolts (E9X, E46 M3 only)
- 3 M10 Rear flange bolts
- 3 M10 front flange bolts
- 1 Small tube of Loc-tite medium thread locker
CARBON DRIVESHAFTS ARE CONSIDERED CUSTOM PER ORDER AND CANNOT BE CANCELLED ONCE MADE.
PLEASE ORDER CAREFULLY!
-
N54 Specific bracket for our Midual VTT catch cans. This is for the Dual can version. Mounts to the driver side strut bar.
