-
Sale!
Black Tial BOV Spring
$54.99$49.99If running a Tial BOV on your N54 instead of the TurboSmart Raceport you want to run the black spring. This will provide you with the most complete vent, and eliminate any chance for flutter/surge. -
Sale!
BMW/Toyota 5×112 to 5×114 Bolt Pattern Conversion Kits
$69.99 – $129.99Looking to convert your 5x112 M14x1.25 vehicle such as A90/91 Toyota Supra, and 2020+ BMW G-series to 5x114 to open up your wheel options? We got covered with our VTT wheel stud conversion kits. These kits are forged cold-rolled steel in 10.9 class, with corrosion-resistant coating for years of use, and convert your vehicle to M12x1.50 wheel studs which allow you to fit 5x114 wheels with no other changes.PLEASE NOTE – THESE STUDS WILL ONLY WORK IF YOUR WHEELS ARE DRILLED M14 THESE WILL NOT WORK FOR WHEELS DRILLED M12!
DO NOT USE ANY HUB-CENTERING SLEEVES WITH THESE CONVERSION STUDS, THE LUGS WILL CENTER THE WHEELS. THE USE OF A CENTERING SLEEVE MAY LEAD TO STUDS BREAKING. FOR INSTALLATION YOU MUST SNUG EACH LUG UP SLOWLY, AND IN A STAR PATTERN TO GET THE WHEEL CENTERED ON THE LUGS, FAILURE TO DO SO CAN ALSO LEAD TO FAILURE.
-
Unsure of the state of your CHRA's, whether brand new from a questionable source or rebuilt? DON'T install them without having a proper High-Speed balance done! This is the #1 most critical factor when building a turbocharger, and is even more important for performance turbochargers or small twins that see a LOT of RPM. We use a Turbo Technics VS3 balancer, and balance most units down to under .5G Not all turbos will be able to pass a high-speed balancing test for any number of reasons (usually poor assembly, bent shaft, etc), if they will not pass, we will send you the specs they are in, and as close as we could get them. We then will give you the option to send them back, or we can disassemble, and rebuild them in-house using our other balancing, and assembly tools to ensure a properly built/balanced unit. The service is $79.99 each for most turbos, and we have the capabilities to balance most units. If sending in twins please choose TWO as the quantity
UNITS MUST BE SENT IN WITH NO HOUSINGS, AND IN A CONDITION READY TO BE BALANCED, IF YOU NEED TO SEND IN COMPLETE TURBOS, WE CAN DISASSEMBLE, AND BALANCE FOR YOU, BUT AN EXTRA CHARGE WILL APPLY. IF THE UNITS ARE SENT IN A CONDITION WHERE THEY CAN NOT BE BALANCED WE WILL LET YOU KNOW THE PRICE TO GET THEM TO A STATE WHERE THEY CAN BE
-
Sale!
CNC N54/N55 Single Flange
$309.99 – $389.99100% CNC flange in mild or SS. This flange will fit all N54's and N55's and comes COMPLETE ready for welding your runners onto it -
N54 “GC 2.0” Stock Location Turbocharger Kit (fits all N54 models)
From:$4,199.00$2,759.99All new design for 2018! We are proud to introduce the latest in our line of N54 turbocharger products the VTT "GC" 2.0 turbochargers. This is a new N54 turbocharger from the ground up, using 100% new parts throughout. -
N54 “GC LITE 2.0” Stock location Turbocharger Kit
From:$3,199.00$2,489.99We are proud to introduce the latest in our line of N54 turbocharger products the VTT "GC LITE" 2.0 turbochargers.WHP Level supported (with proper fuel, upgrades, and tuning) Stock-700WHP -
N54 Aluminum Turbo Outlet
$229.99 – $319.99Looking to get the most efficient turbocharger operation out of your N54-powered BMW? The best way to do this is to remove all restrictions from the inlet and charge the tract. The factory charge pipe has a very small 1" opening and a poorly designed Y section that couples the two banks into one before entering the intercooler. This VTT N54 Aluminum outlet gets rid of those restrictions and provides a full 1.5" from the turbochargers to a smooth Y transition into a 2.5" outlet to fit most aftermarket intercoolers. Do not be fooled by companies trying to sell you oversized 2" charge pipes, these are not going to pick up any power, and will kill velocity. The smallest diameter you can run while still providing adequate flow is always best for flow velocity and reducing time to TQ. -
Looking for a little extra clearance on your coolant tank fitting due to relocation for single turbo, forward-facing intake manifold, etc. This 90-degree fitting will allow you to run the hose straight down instead of straight out, and increase your clearance, and routing choices. Made of 6061-T6 and anodized black for a long-lasting finish. Comes with fitting, and 1 clamp.
-
N54 CHRA REPLACEMENT OEM / STAGE 1
Starting At $424.00Need N54 turbo replacements, don't have full turbo replacements in your budget, like wrenching on your own stuff? If you answered yes to any of those questions, the VTT N54 CHRA replacements are perfect for you! -
N54 F-RB Turbocharger Kit
From: $2,759.99WHP Level supported (with proper fuel, upgrades, and tuning) Stock-850WHP VTT is proud to announce an All-new VTT GC redesign for 2021! The latest in our line of N54 VTT “GC” turbochargers. The GC “F-RB” or Full-Rebrand.This is an all-new take on the VTT N54 “GC” turbocharger, using 100% new parts throughout that is pure performance. Some of the new groundbreaking features include: All turbine side parts are now fully cast from 310 Stainless Steel for increased temperature resistance, and ultimate corrosion resistance. We also fully redesigned the turbine housing -the F-RB's have a much larger volute as well as a proprietary AR which will dramatically increase flow capacity, helping to eliminate stress on the turbine wheel. Fully redesigned compressor housings which now include V-band OR Hose Barb connection options (while our current stock of hose barb connections last). The CHRA’s are redesigned with new compressor wheels, bullet nuts, and better internal parts. These are new turbochargers from the compressor housing to the bearing housing, to the turbine housing, we had them engineered to fit in the stock N54 location, but provide the full flow of a much larger turbo, and providing a flow increase over the V2 “GC”.
With this all-new design, there is no other 850WHP capable turbocharger option on the market single or twins that can match the spool, ease of fitment, power, reliability, OR price of our GC “F-RB” turbochargers!
