-
NGK 95706 Spark plug set required for running 100% e85, and high boost on many BMW applications, including N54, N55, S55, etc. Plugs can be bought as a set of 6. You can add pre-gapping for an additional charge
-
Looking to protect your single turbo investment, dont have a ton of room, and need a low profile filter that can flow what you need? VTT Has you covered with our Low Profile Single turbo Air Filters. These filters are custom-made for VTT. They are made with a heat-resistant silicone base, and a high-flowing cotton weave element with a pre-oiled design to catch contaminates but allow free flow. We currently offer them in Black, and 3 flange sizes. 3", 4" and 5" flange. With two filter heights. Tested at over 1200WHP with no loss of power observed. Filter Options - Offered in White, and Black with the following dimensions Short - 3.75" Tall, 7.5" OD Large end, 5" Small end 3", 4", or 5" Flange Tall - 4.5" Tall, 7.5" OD Large end, 5" Small end 3", 4", or 5" Flange
-
Need a Tee fitting for plumbing Vacuum, or Boost lines, Don't want to use cheap plastic ones that can get soft when hard, and brittle after they heat cycle? We didn't either, which is why we machined these high-quality billet tees to solve this issue. Machine from 6061-T6 aluminum, and anodized in black for a long-lasting corrosion-free finish, these tees look great, and will you never have to worry about one failing. We offer them in two sizes, each size has 12mm legs and 3 barbs:
- 7.60mm / -4 Push Lock for people looking to use -4 push lock hose or -4 AN hose. This is a perfect fit for those.
- 1/4" For people looking to use 1/4" vacuum tube
-
Looking to up your boost limit on just about any BMW vehicle that runs a 3 or 4-wire BMW map sensor including but not limited to S58, B58, N54, N55, S55, S63, B48, B47, B42, B57, B46? We were too, so we decided to make a very easy plug-and-play kit for 3, and 4-wire BMW map sensors. These kits will allow you to completely replace the 3-wire sensor with one of our sensors, leave your stock 4-wire in place for IAT sensing, and move the power, ground, and sensor signal from the factory sensor to our sensor. These sensors have the proper scaling which will allow your tuner to simply change your map sensor scaling in the tune, and the factory ECU will be able to utilize the sensor voltage with no problem. We are offering these in 5 bar (58 psi), and 6 bar (72 psi), and each comes with a plug-and-play harness, and optional fittings for ease of installation.
Note: For the S58/B58 our Factory style Pre-Throttle map sensor is also 5 bar, and will work fine coupled with the post throttle kit, but the scaling is different, if you want matching Voltages Pre/Post throttle you can run two of these.
A variety of install pics can be found below and - Here
Scaling PDF Links: 5-Bar / 6-Bar
Features include:- Plug and Play harnesses with no wire splicing
- Output wire for connecting a PI or external controller to your post-throttle map sensor for the most stable signal that is not affected by throttle closure
- Different fittings are available for your plumbing needs.
- Can have matching voltage signals for pre/post throttle for ease of tuning, and boost reference
- B58/S58 etc Pre Throttle - 3 Wire Harness (Charge pipe to 1/8" NPT adapter needed, for B58/S58 90 degree adapter needed to provide sensor clearance)
- B58/S58 Post Throttle - 4 Wire Harness (Boost reference will be needed from manifold to sensor)
- F90 M5 Pre/Post Throttle - 4 Wire Harness (May need to repin) (Boost reference will be needed from manifold to sensor)
- Most all other platforms Pre/Post Throttle - 4 Wire Harness (May need to repin) (Boost reference will be needed from manifold to sensor)
- B58
- S58
- S63/ S63TU
- N63
- N54
- S55
- N55
- N20
- B46
- B48
- B57
- B47
-
Looking for Mac solenoids for your build? We got em here at VTT-FAB so you can get everything in one place. We have 3-port, and 4-port in stock!
-
Unsure of the state of your CHRA's, whether brand new from a questionable source or rebuilt? Don't install them without having a proper High-Speed balance done! This is the #1 most critical factor when building a turbocharger, and is even more important for performance turbochargers or small twins that see a LOT of RPM. We use a Turbo Technics VS3 balancer, and balance most units down to under .5G Not all turbos will be able to pass a high-speed balancing test for any number of reasons (usually poor assembly, bent shaft, etc), if they will not pass, we will send you the specs they are in, and as close as we could get them. We then will give you the option to send them back, or we can disassemble, and rebuild them in-house using our other balancing, and assembly tools to ensure a properly built/balanced unit. The service is for most turbos, and we have the capability to balance most units, NOT ALL. If sending in twins please choose TWO as the quantity
UNITS MUST BE SENT IN WITH NO HOUSINGS, AND IN A CONDITION READY TO BE BALANCED, IF YOU NEED TO SEND IN COMPLETE TURBOS, WE CAN DISASSEMBLE, AND BALANCE FOR YOU, BUT AN EXTRA CHARGE WILL APPLY. IF THE UNITS ARE SENT IN A CONDITION WHERE THEY CAN NOT BE BALANCED WE WILL LET YOU KNOW THE PRICE TO GET THEM TO A STATE WHERE THEY CAN BE
-
We have a variety of fittings in stock to help you get your turbo system plumbed up! Available are:
- 1/8" NPT to -6 AN Male (Great for water lines, or anywhere you need a small 1/8" NPT to -6 Male AN)
- M14x1.5 to -6 AN Male (Great for water lines on Garrett turbos GT, GTX, and G-Series, or anything that has a metric M14x1.5 thread and you need a -6AN male)
- .035" Turbo feed restrictors. These are for Garrett turbochargers and will fit GT, GTX, and G- Series up to G35
- Garret GT, GTX, and G-Series up to G35 -8 An drain adapter. For those that want a low profile -8 drain for their GT-G-Series Garrett. (Comes with two bolts, and a gasket)
-
VTT is proud to offer our EWG "Direct Control System" or DCS! This is a completely new innovation for people looking to control the highest-flowing wastegate on the market using an existing BMW electronic actuator. This system will allow BMW owners who have a vehicle with Electronic Wastegates from the factory to utilize this system to control an externally wastegated turbo system, AND it will ALSO allow ANY vehicle to use this setup to control your own custom turbo system. This is done by utilizing our custom 7075 Billet aluminum bracket coupled with a Turbosmart Straight gate, and if needed an EWG controller made for us by DCCD Pro. This allows direct external wastegate control over any turbocharger system with or without EWG for the factory. Features:
- Utilizes the most current wastegate technology the Turbosmart Straight Gate. This gate allows maximum flow with minimal restriction, low drive pressure, and much more. Full details can be found here - https://www.turbosmart.com/product/electronic-straightgate-esg50-external-wastegate/
- Can be configured in multiple ways, and angles based on how you mount the adapter
- The adapter is 7075 Aluminum which has the strength of steel and weight of aluminum
- All connection fittings, are made from Nitronic 60 which has extremely high temperature and wear properties
- Zero Drive Pressure, no springs, no poppet valves, direct control over the gate using factory ECU logic
- Adaptable to ANY turbo system on any car to provide the ultimate in boost control!
-
Sale!
VTT F9X M5 / M8
Blow-Off Valve (BOV) Kit — S63 Engine
Fits BMW F90 M5 & F91 / F92 / F93 M8 (All Trims)
Why the S63 Needs a Proper Blow-Off Valve
As capable as the S63 platform is in the F9X M5 and M8, one critical component is missing from the factory configuration: a true diverter valve (DV) or blow-off valve (BOV) to properly vent excess boost pressure during throttle lift.
From the factory, the S63 relies on Valvetronic to manage pressure relief. While this strategy works from an OEM drivability standpoint, it is not an effective method of fully venting boost pressure. Under higher load, rapid throttle closures, or tuned conditions, this can lead to compressor surge, increased stress on the turbochargers, and reduced turbocharger longevity over time.
The VTT BOV Kit adds the missing mechanical venting solution the S63 needs. By properly evacuating excess boost pressure during throttle lift, this system:
-
Reduces compressor surge
-
Protects turbochargers under aggressive driving
-
Improves long-term reliability
-
Delivers the signature BOV sound enthusiasts expect
This is a functional upgrade first—sound is simply the byproduct.
If upgrading Turbos on your F9x, this kit is something we feel is required to increase longevity
-
-
Sale!
VTT F9X M5 / M8
Complete Turbo-Side Intake System (S63)
VTT is proud to offer a true full turbo-side intake system for the BMW F9X M5 and M8 platforms, equipped with the S63 engine, that eliminates every factory airflow restriction from the turbocharger inlet all the way to the air filter.
Most intake kits on the market only replace the upper airbox or filter section, while leaving the restrictive factory molded plastic turbo inlet piping in place. That turbo-side inlet is the primary airflow choke point on the S63 platform—meaning those kits only address half of the problem.
Our system replaces the entire factory intake tract, starting directly at the turbochargers, with precision-machined 6061-T6 billet adapters that bolt straight to the compressor inlets. Airflow then transitions smoothly into reinforced 2.5” → 4” high-temperature silicone tubing, finishing with dual VTT 4” dry-element air filters.
This is a true unrestricted intake system—no factory bottlenecks left behind—allowing the S63 to breathe properly under both stock and increased airflow demand.
