-
Sale!
BMW Factory OEM EWG Actuator Replacement – 11 65 8 691 853
$499.00$349.00Looking to replace your damaged factory BMW Actuator part number - 11658691853 VTT has located and ordered in bulk these actuators, and offer them at a discounted price. These are 100% FACTORY BMW OEM actuators, not aftermarket. Fitment is for the following, but they work to replace basically any BMW Actuator. -
Sale!
BMW/Toyota 5×112 to 5×114 Bolt Pattern Conversion Kits
$69.99 – $129.99Looking to convert your 5x112 M14x1.25 vehicle such as A90/91 Toyota Supra, and 2020+ BMW G-series to 5x114 to open up your wheel options? We got covered with our VTT wheel stud conversion kits. These kits are forged cold-rolled steel in 10.9 class, with corrosion-resistant coating for years of use, and convert your vehicle to M12x1.50 wheel studs which allow you to fit 5x114 wheels with no other changes.PLEASE NOTE – THESE STUDS WILL ONLY WORK IF YOUR WHEELS ARE DRILLED M14 THESE WILL NOT WORK FOR WHEELS DRILLED M12!
DO NOT USE ANY HUB-CENTERING SLEEVES WITH THESE CONVERSION STUDS, THE LUGS WILL CENTER THE WHEELS. THE USE OF A CENTERING SLEEVE MAY LEAD TO STUDS BREAKING. FOR INSTALLATION YOU MUST SNUG EACH LUG UP SLOWLY, AND IN A STAR PATTERN TO GET THE WHEEL CENTERED ON THE LUGS, FAILURE TO DO SO CAN ALSO LEAD TO FAILURE.
-
Unsure of the state of your CHRA's, whether brand new from a questionable source or rebuilt? DON'T install them without having a proper High-Speed balance done! This is the #1 most critical factor when building a turbocharger, and is even more important for performance turbochargers or small twins that see a LOT of RPM. We use a Turbo Technics VS3 balancer, and balance most units down to under .5G Not all turbos will be able to pass a high-speed balancing test for any number of reasons (usually poor assembly, bent shaft, etc), if they will not pass, we will send you the specs they are in, and as close as we could get them. We then will give you the option to send them back, or we can disassemble, and rebuild them in-house using our other balancing, and assembly tools to ensure a properly built/balanced unit. The service is $79.99 each for most turbos, and we have the capabilities to balance most units. If sending in twins please choose TWO as the quantity
UNITS MUST BE SENT IN WITH NO HOUSINGS, AND IN A CONDITION READY TO BE BALANCED, IF YOU NEED TO SEND IN COMPLETE TURBOS, WE CAN DISASSEMBLE, AND BALANCE FOR YOU, BUT AN EXTRA CHARGE WILL APPLY. IF THE UNITS ARE SENT IN A CONDITION WHERE THEY CAN NOT BE BALANCED WE WILL LET YOU KNOW THE PRICE TO GET THEM TO A STATE WHERE THEY CAN BE
-
N63/N63TU – S63/S63TU Stage 1 TurboCharger Upgrade
$3,149.99 – $4,199.99WHP Level supported (with proper fuel, upgrades, and tuning) Stock-800WHP We are proud to introduce the first in our line of N63/N63TU - S63/S63TU turbocharger products the VTT Stage 1 hybrid turbochargers. If you are ready to take your N/S63-powered vehicle to the next level, this is the upgrade for you. We start with a fresh rebuild using all factory spec internals, then we machine the stock compressor housings to take our own custom-sized VTT billet compressor wheels, these wheels can support up to 800WHP with the proper tuning and fuel. We then triple balance the wheels, CHRA, and assemble them into the freshly prepared housings. Please select your model -
NGK 97506 Pre-Gapped Spark Plug Set
$104.99 – $139.99NGK 95706 Spark plug set required for running 100% e85, and high boost on many BMW application including N54, N55, S55, etc. Plugs can be bought as a set of 6. You can add pre-gapping for an additional $25 -
PTE – Precision Turbochargers
$2,234.49 – $4,428.99VTT is proud to offer PTE Turbocharger products! -
VTT “DCS” EWG System for TurboSmart Straight Gates
$799.99 – $1,499.99VTT is proud to offer our EWG "Direct Control System" or DCS! This is a completely new innovation for people looking to control the highest-flowing wastegate on the market using an existing BMW electronic actuator. This system will allow BMW owners who have a vehicle with Electronic Wastegates from the factory to utilize this system to control an externally wastegated turbo system, AND it will ALSO allow ANY vehicle to use this setup to control your own custom turbo system. This is done by utilizing our custom 7075 Billet aluminum bracket coupled with a Turbosmart Straight gate, and if needed an EWG controller made for us by DCCD Pro. This allows direct external wastegate control over any turbocharger system with or without EWG for the factory. Features:- Utilizes the most current wastegate technology the Turbosmart Straight Gate. This gate allows maximum flow with minimal restriction, low drive pressure, and much more. Full details can be found here - https://www.turbosmart.com/product/electronic-straightgate-esg50-external-wastegate/
- Can be configured in multiple ways, and angles based on how you mount the adapter
- The adapter is 7075 Aluminum which has the strength of steel and weight of aluminum
- All connection fittings, are made from Nitronic 60 which has extremely high temperature and wear properties
- Zero Drive Pressure, no springs, no poppet valves, direct control over the gate using factory ECU logic
- Adaptable to ANY turbo system on any car to provide the ultimate in boost control!
-
VTT is proud to offer our "OBD-LOCK" OBD port locking tool. This tool is made from billet 6061-T6 aluminum and is designed to completely lock out your OBD port from being accessed. This is useful for people who do not want dealers, techs, etc from accessing their OBD port, and possibly changing a tune, etc. This is also perfect for anti-theft prevention as it will not allow a would-be thief to hook up to the car's OBD port, duplicate a key, etc. The OBD-LOCK cannot be removed without physically destroying the OBD port if you do not have the proper tools. VTT uses 5 types of screw head designs for every 200 OBD-LOCKS made. This means that worldwide only 40 OBD-LOCKS are using the same head design. For each batch of 200, we redesign the screw heads meaning every batch of 200 OBD-LOCKS will use different screw heads and tools. Each OBD-LOCK sent has its head design chosen at random. After Extensive testing, we have found that our OBD lock fits EVERY SINGLE OBD port we have tried, this means it will fit every single OBD port currently on the market from a high-end BMW to a Ford F150 diesel. If you order one, and find it does not fit, PLEASE let us know.
FITMENT: We have TWO versions one for ALL GM vehicles and one for ALL NON-GM Vehicles. Please order the one you
-
Show off your VTT support and get a good laugh from people with our "We Like To Party" License plate bracket. Born from the infamous quote in Talladega nights
-
Looking to protect your single turbo investment, dont have a ton of room, and need a low profile filter that can flow what you need? VTT Has you covered with our Low Profile Single turbo Air Filters. These filters are custom-made for VTT. They are made with a heat-resistant silicone base, and a high-flowing cotton weave element with a pre-oiled design to catch contaminates but allow free flow. We currently offer them in Black, and 3 flange sizes. 3", 4" and 5" flange. With two filter heights. Tested at over 1200WHP with no loss of power observed. Filter Options - Offered in White, and Black with the following dimensions Short - 3.75" Tall, 7.5" OD Large end, 5" Small end 3", 4", or 5" Flange Tall - 4.5" Tall, 7.5" OD Large end, 5" Small end 3", 4", or 5" Flange
-
Sale!
VTT 15″/17″ Drag Pack Wheels for BMW/Toyota/VAG
$269.99 – $349.99Looking for a Lightweight, AFFORDABLE drag pack that looks amazing for your BMW, Toyota, or VAG platform? Look no further! VTT is proud to announce our lineup of Drag pack wheels for various BMW/Toyota/VAG fitments! We teamed up with Rota and had them open custom molds for us of their extremely popular Grid design. With these molds, we have an exclusive on 15X10, 17X10, and 17X4.5 wheels in our exact specs. The wheels currently are offered in the colors and sizes belowWe chose ET45 across the board on the rear as this is a universally easy offset to fit and can be made to fit just about any application with the use of a spacer. - VTT Spacers can be found here - https://vargasturbo.com/product/vtt-billet-wheel-spacers/
Wheels are priced EACH, meaning per wheel
PLEASE NOTE! CHECK FITMENT CAREFULLY. ANY WHEELS THAT HAVE HAD TIRES MOUNTED OR ARE DAMAGED DURING TEST FITTING ETC ARE NOT RETURNABLE!
We make NO CLAIM these fit ANY PLATFORM, or ANY factory brake set up. It is YOUR JOB to measure, and make sure they will fit BEFORE you mount tires or install them. WE NEVER suggest shaving down brake calipers to fit a smaller wheel. If they do not fit. GET A SMALL BRAKE KIT!
Colors offered:- Satin Black
- Gloss Black
- Bronze,
- Gun Metallic
- 15x10 ET45 (wheel weight 16 lbs)
- 17x10 ET45 (wheel weight 19lbs)
- 17x4.5 ET-20 (wheel weight 16lbs)
- 15x10 ET45 - (wheel weight 16 lbs)
- 17x10 ET45 (wheel weight 19 lbs)
- 17x4.5 ET-20 (wheel weight 16 lbs)
-
Looking to remove your BOV either for leak testing, or dont want to run one, and your charge pipe or housing has a flange on it. You can use this billet plate to block off the BOV flange. Uses the O-ring from the BOV to seal, and removes the BOV. Fitment: Tial BOV Turbosmart BOV with female flange like Tial
-
Looking to adapt your wheel bore size to a smaller hub bore? VTT has you covered with our hub-centric adapters. These adapters are made from Billet 6061-T6 aluminum, and anodized in black. We have these sizes currently
- 57.1mm hub to 60.1mm wheel bore
- 57.1mm hub to 64.1mm wheel bore
- 57.1mm hub to 66.1mm wheel bore
- 57.1mm hub to 66.6mm wheel bore
- 57.1mm hub to 67.1mm wheel bore
- 57.1mm hub to 70.3mm wheel bore
- 57.1mm hub to 71.6mm wheel bore
- 57.1mm hub to 72.6mm wheel bore
- 57.1mm hub to 73mm wheel bore
- 57.1mm hub to 74mm wheel bore
- 57.1mm hub to 74.1mm wheel bore
- 64.1mm hub to 72.6mm wheel bore
- 66.6mm hub to 72.6mm wheel bore
They are sold in sets of two, order TWO SETS for a full car, or one set per axle.
-
VTT is Proud to offer our Billet Aluminum DCT Transmission pan. This pan does away with the factory plastic pan and upgrades it to 6061-T6 aluminum anodized in a variety of colors. This pan increases fluid capacity by 80% or almost DOUBLE the stock pan, has a US-made reusable Viton Gasket, a rare earth magnet built in to pull metal from the fluid, machined external fins to help aid in cooling, and a -6 ORB drain plug. Product Features:
- Billet construction using 6061-T6 aluminum for long life, and added strength
- 80% or Almost DOUBLE the factory fluid capacity at 2000ML compared to 1150ML
- Machined fins for improved cooling
- Rare Erath magnet built in to pull metal from the fluid
- US-Made Viton Gasket
- -6 ORB drain plug for easy service
-
VTT Billet CNC oil caps add a nice touch of quality to an otherwise plastic-filled BMW engine bay. We offer these in red, black, blue Purple, gold, and clear anodizing. Made from 6061-T6 aircraft aluminum with stainless steel locking tabs. Fits ALL BMWs with a two-prong locking tab design, including but not limited to. N54, N55, S55, S54, N20, S63, S63TU, M54, B58, N63, S65, S85, M57 DieselTHIS CAP DOES NOT FIT, B58TU, S58, A90/91 SUPRA, THIS ONLY FITS 2 PRONG CAP STYLE
-
VTT is proud to offer our billet replacement for the factory plastic Coolant Reservoir cap. This cap does away with the weak plastic cap while adding some pop, and color to your engine bay. These Coolant caps retain ALL of the factory provisions by simply allowing you to snap the factory pressure-relief into the new Billet Cap We also designed these caps to complement our N5X Billet Oil caps, N5XBillet Oil filter housing caps, and Billet Power Steering cap and so all 4 will have the same design. We offer these caps in 4 colors - Red, Black, Blue, and Clear anodize, as well as a choice of custom anodize at a cost of $100 extra.
