• Sale!

    VTT Billet Check Valves

    $24.99$29.99
    VTT CNC Billet check valve that can be used for a variety of uses including a vacuum/boost check valve when removing the stock PCV system, and still wanting to run vacuum to the crankcase. Rated at over 100 psi, with a cracking psi of .25psi.

  • VTT Ignition Coil Kits

    $159.99$209.99
    VTT is proud to offer ignition coil replacements for the N5X platforms, as well as B5X, and many VAG platforms. We started our quest for coils by contacting multiple coil manufacturing companies, paying for individual coils to be made then putting them through rigorous testing in the USA to ensure they matched or exceeded factory output. Once we were satisfied with the testing, we had the best performing coils made to our colors and specs. We offer these coils as complete sets for the N54, B58/S58, and the VAG platforms in either 4, or 5 cylinders. We also offer upgraded plugs which are highly recommended to change when doing coil replacements These coils come in 3 colors, Red, Black, and Blue, and are not simply an aesthetic upgrade but match or exceed the factory secondary spark energy. The VAG coil, is extremely potent, and the tester was so impressed with it compared to the factory coil, he called it a "BEAST" of a coil

    Note:  To extract maximum performance from VTT coils minor tune changes are required to optimize dwell periods. See recommended Dwell times below

  • Sale!

    VTT VAG Billet One Way Crankcase Breather

    VTT is happy to introduce the first and only available plug and play crankcase breather kits for ALL VAG (VW/AUDI/Porsche) applications that use the latch type in the photos(full application list below). With this breather simply remove your oil cap, install the breather, and instantly free up horsepower, improve turbo draining, remove crankcase pressure, all while adding a cool look to your engine bay.

  • Need a replacement filter for your VTT Billet Crankcase breather? You can order on here. We offer them in 3 heights, low 48mm, medium58mm, and tall 68mm. This is measured from base to top. The filter will include a new clamp. For reference: N54/55 mostly use the low A90 Supra use Medium Most Audi applications can fit a tall, but measure your filter before ordering.

  • VTT offers silicone hoses in various Push-lock sizes, we use these for our catch can kits, but they are also suitable for coolant, vacuum, boost, etc. Do not use with fuel. We offer: -10 Push Lock 24", and 18" -8 Push Lock 24", and 19.5" -6 Push Lock 24"

  • Not available for single can external PCV Valve.

  • VTT is proud to offer our "OBD-LOCK" OBD port locking tool. This tool is made from billet 6061-T6 aluminum and is designed to completely lock out your OBD port from being accessed. This is useful for people who do not want dealers, techs, etc from accessing their OBD port, and possibly changing a tune, etc. This is also perfect for anti-theft prevention as it will not allow a would-be thief to hook up to the car's OBD port, duplicate a key, etc. The OBD-LOCK cannot be removed without physically destroying the OBD port if you do not have the proper tools. VTT uses 5 types of screw head designs for every 200 OBD-LOCKS made. This means that worldwide only 40 OBD-LOCKS are using the same head design. For each batch of 200, we redesign the screw heads meaning every batch of 200 OBD-LOCKS will use different screw heads and tools. Each OBD-LOCK sent has its head design chosen at random. After Extensive testing, we have found that our OBD lock fits EVERY SINGLE OBD port we have tried, this means it will fit every single OBD port currently on the market from a high-end BMW to a Ford F150 diesel. If you order one, and find it does not fit, PLEASE let us know.

    FITMENT: We have TWO versions one for ALL GM vehicles and one for ALL NON-GM Vehicles. Please order the one you

  • Tired of your Dragy flying all over the car as you try to do runs? Tired of low sats or no sats warning due to improper location of the Dragy in the vehicle? Well say goodbye to those issues with our new Carbon Fiber and Plastic Dragy holders. These are made from either 100% Pre-Preg Carbon Fiber, or molded plastic for a perfect fit. The carbon fiber gives it just the right look to add to your performance vehicle! Each holder has dual Suction cups and will stick to any smooth surface. We suggest mounting them in the upper left or right corner of your windshield with a full view of the sky. Dragy holder features  
    • Stop your Dragy from flying off the dash, and having to search for it
    • Position your Dragy in the optimal position for the best satellite coverage
    • VTT Dragy holder exposes the entire top of the Dragy so nothing is blocking the receiver from the Satellite
    • The charging port is not blocked and can be accessed with the cover on
    • Choose from REAL Carbon Fiber or Molded Plastic
         

  • Looking to go above 31PSI on your VAG vehicle that uses SENT map sensors? If so you will need this 4-bar SENT sensor with integrated IAT. These are plug and play for most 2.5L engines including DAZA, and DNWA(US VERSION), as well as some other VAG platforms. You will need to have your tuner rescale your map for the sensor, but that is the only change needed. We offer them in pairs only, which is needed on most vehicles.

  • VTT is proud to offer the very best charge pipe solution for the VAG MK7 Golf/Jetta/A3 platforms. This system completely does away with the restrictive, and muli-connection stock charge pipe system, and replaces it with two single 6-ply, Heat Resistant, Wire reinforced silicone charge pipes rated at over 200 psi.  They are molded for the perfect fit in your engine bay, while not sacrificing anything in the way of flow or size.

  • Sale!
    Looking to spice up the engine bay of your Audi/VW or Porsche without spending a ton of money. Our Billet Oil caps come in 5 colors and will look great in any engine bay. CNC machined from a billet of 6061-T6 Aircraft aluminum they sport a factory fit and finish with a Viton O-ring for long a leak-free life. They fit a WIDE variety of vehicles and directly replace your factory oil cap.  

  • Show off your VTT support and get a good laugh from people with our "We Like To Party" License plate bracket. Born from the infamous quote in Talladega nights

  • Building a kit using Mac solenoids to control boost? Need an easy way to mount it? VTT-FAB has you covered with our billet Mac Solenoid brackets. Machined from 6061 billet and anodized in 3 colors, these are the perfect way to mount your Mac valve and look good while doing it. Each kit includes:
    • One Mac Solenoid bracket (3-Port or 4-Port)
    • 2 Allen screws to hold the valve to the bracket
    • M6 Mounting Bolt

  • Sale!
    With the VTT COMPLETE Catch can set up, we completely address the low AND high sides, by separating them, and running each side into its own chamber in the catch can. We do this using a custom PCV plate, that organizes the HIGH and LOW sides into nice short hose runs and uses strategically placed check valves to keep boost out of your crankcase, and in the manifold where it belongs. Our opening in the PCV plate is baffled, and the plate chambers themselves are filled with Stainless mesh to knock down any oil mist, and the catch can is also filled with this mesh. This means any oil is knocked out of the air BEFORE it gets to your intake ports or turbocharger inlet. We completely redesigned what people think of then they see an MQB catch can set up. VOLUME in the PCV system is just as important as the vacuum itself. Every set on the market runs lines across the ENTIRE engine bay, this long run, mean vacuum drop, and volume loss, this equals poor PCV operation. Our system mounts the can directly over the cold side of the turbocharger against the firewall, and the longest hose run is only a little over 9". We also use all custom CNC aluminum Banjo fittings, and Banjo Bolts, even our check valves are custom fitted into banjo Fittings. The -6 Banjo that pulls vacuum for the low side also serves as a place to run a boost tap if wanted. This makes it easy to run a boost reference for BOV, Boost gauge, 1:1 FPR reference, etc.

  • VTT Virtual Gift Card

    $50.00$1,000.00

    Please Note: This is a Virtual Gift Card.  After purchase you will receive an email with your Gift Card code

  • Need a Tee fitting for plumbing Vacuum, or Boost lines, Don't want to use cheap plastic ones that can get soft when hard, and brittle after they heat cycle? We didn't either, which is why we machined these high-quality billet tees to solve this issue. Machine from 6061-T6 aluminum, and anodized in black for a long-lasting corrosion-free finish, these tees look great, and will you never have to worry about one failing. We offer them in two sizes, each size has 12mm legs and 3 barbs:
    • 7.60mm / -4 Push Lock for people looking to use -4 push lock hose or -4 AN hose. This is a perfect fit for those.
    • 1/4" For people looking to use 1/4" vacuum tube

  • VTT is proud to offer our EWG "Direct Control System" or DCS! This is a completely new innovation for people looking to control the highest-flowing wastegate on the market using an existing BMW electronic actuator. This system will allow BMW owners who have a vehicle with Electronic Wastegates from the factory to utilize this system to control an externally wastegated turbo system, AND it will ALSO allow ANY vehicle to use this setup to control your own custom turbo system. This is done by utilizing our custom 7075 Billet aluminum bracket coupled with a Turbosmart Straight gate, and if needed an EWG controller made for us by DCCD Pro. This allows direct external wastegate control over any turbocharger system with or without EWG for the factory. Features:
    • Utilizes the most current wastegate technology the Turbosmart Straight Gate. This gate allows maximum flow with minimal restriction, low drive pressure, and much more. Full details can be found here - https://www.turbosmart.com/product/electronic-straightgate-esg50-external-wastegate/
    • Can be configured in multiple ways, and angles based on how you mount the adapter
    • The adapter is 7075 Aluminum which has the strength of steel and weight of aluminum
    • All connection fittings, are made from Nitronic 60 which has extremely high temperature and wear properties
    • Zero Drive Pressure, no springs, no poppet valves, direct control over the gate using factory ECU logic
    • Adaptable to ANY turbo system on any car to provide the ultimate in boost control!

  • VTT is proud to offer the very best EASY-TO-INSTALL charge pipe solution for the 2013-2018 Cummins platform. This system completely does away with the restrictive, and muli-connection stock charge pipe system, and replaces it with two single 7-ply, Heat Resistant, Wire reinforced silicone charge pipes rated at over 250 psi. DON'T struggle trying to install aftermarket hard pipes with 8 clamps, and cuss-worthy space to try to squeeze them in! These are molded for the perfect fit in your engine bay, while not sacrificing anything in the way of flow or size. They also completely isolate your charge air from any additional heat soak coming in from the engine or ambient heat. The stock hot side pipes have many irregular shapes and turns causing turbulence as well as carrying heat.

  • Looking to protect your single turbo investment, dont have a ton of room, and need a low profile filter that can flow what you need? VTT Has you covered with our Low Profile Single turbo Air Filters. These filters are custom-made for VTT. They are made with a heat-resistant silicone base, and a high-flowing cotton weave element with a pre-oiled design to catch contaminates but allow free flow.  We currently offer them in Black, and 3 flange sizes. 3", 4" and 5" flange. With two filter heights. Tested at over 1200WHP with no loss of power observed. Filter Options - Offered in White, and Black with the following dimensions Short - 3.75" Tall, 7.5" OD Large end, 5" Small end 3", 4", or 5" Flange Tall - 4.5" Tall, 7.5" OD Large end, 5" Small end 3", 4", or 5" Flange

  • VTT Physical Gift Cards

    $50.00$1,000.00

    Give the Gift of VTT! Looking to get your friends, or family some go-fast parts, and no idea what they need, only that they love VTT? Well, our Gift Cards have you covered! They come in $50, $100, $250, $500, and $1000 increments. Each gift card is precision cut out of plastic in the shape of the VTT logo and has the dollar amount and the code on the back. Each gift code is unique and is locked to that card. To redeem simply enter the code during check out it will remove that amount, and if you have any leftover it will go back to the card.

    You can choose to have your card physically mailed to you, or a virtual card where we can send you a scan of your card.

Title

Go to Top