-
VTT Universal Turbo Fittings – Oil & Coolant Solutions for BMW Turbo Builds!
Looking to fabricate your own turbo kit for BMW platforms? Need an easy solution to block off water lines or create custom feed and drain fittings? Look no further! VTT offers a wide range of high-quality oil and coolant fittings to simplify your build. Our fittings are designed for most late-model BMW platforms, providing a plug-and-play solution for custom turbo setups. 📌 Available Fitting Options: 🔹 Oil Feed – -4 AN Male 🔹 Oil Drain – -10 AN Male 🔹 Coolant Fittings – Barbed Male or Block-Off Options -
Looking for a high-quality extended turbo drain in a straight or 45-degree angle for Garrett GT, GTX, G series, and T3/T4 (precision, etc). We got you covered with these high-quality billet drain adapters. Flanges available:
- VTT-FAB-062 T3/T4 square opening, Garrett GT/GTX40+/G40+ 3.5" neck, All precision -10AN Male
- VTT-FAB-063 Garrett GT/GTX25-35/G25-G35 3.5" neck -10AN Male
- VTT-FAB-064 Garrett GT/GTX25-35/G25-G35 4" neck -3/4" hose barb
- VTT-FAB-081 T3/T4 square opening, Garrett GT/GTX40+/G40+ 2.5" 45-degree neck, All precision -10AN Male
- VTT-FAB-082 T3/T4 square opening, Garrett GT/GTX40+/G40+ 2.5" 45-degree neck, All precision 3/4" Hose Barb
- VTT-FAB-083 T3/T4 square opening, Garrett GT/GTX40+/G40+ 1" neck, All precision -10AN Male
- VTT-FAB-084 Garrett GT/GTX25-35/G25-G35 2.5" 45-degree neck -10AN Male
- VTT-FAB-085 Garrett GT/GTX25-35/G25-G35 2.5" 45-degree neck -3/4" hose barb
- VTT-FAB-086 Garrett GT/GTX25-35/G25-G35 1" neck -10AN Male
-
Looking to go above 45 psi in your BMW-powered vehicle? Looking for a plug-and-play solution? We have you covered with our BMW 5 bar sensor. These will allow 58 psi to be read and are factory plug-and-play. Simply remove your old sensor, replace it with the 5 bar, and have your tuner rescale your map values in both your DME tune and your PI tune if applicable.
These are GENUINE BMW sensors directly from BMW.
PLEASE NOTE: These are GENUINE BMW sensors directly from THE BMW DEALERSHIP, BMW IS PUTTING A BMW STICKER OVER A DENSO BOX, AND SELLING THEM. THESE DO NOT HAVE BMW STAMPS ON THEM. WE HAVE ZERO CONTROL OVER THIS.
-
Building a kit using Mac solenoids to control boost? Need an easy way to mount it? VTT-FAB has you covered with our billet Mac Solenoid brackets. Machined from 6061 billet and anodized in 3 colors, these are the perfect way to mount your Mac valve and look good while doing it. Each kit includes:
- One Mac Solenoid bracket (3-Port or 4-Port)
- 2 Allen screws to hold the valve to the bracket
- M6 Mounting Bolt
-
Need a Tee fitting for plumbing Vacuum, or Boost lines, Don't want to use cheap plastic ones that can get soft when hard, and brittle after they heat cycle? We didn't either, which is why we machined these high-quality billet tees to solve this issue. Machine from 6061-T6 aluminum, and anodized in black for a long-lasting corrosion-free finish, these tees look great, and will you never have to worry about one failing. We offer them in two sizes, each size has 12mm legs and 3 barbs:
- 7.60mm / -4 Push Lock for people looking to use -4 push lock hose or -4 AN hose. This is a perfect fit for those.
- 1/4" For people looking to use 1/4" vacuum tube
-
Looking for charge pipe weld flanges / Sensor adapters for your custom single turbo kit? We got you covered with some of the more popular flanges, adapters. Features:
- Billet 6061 T6 aluminum
- Raw finish for easy welding
-
Heat is the enemy of power, and the last thing you want is hot coolant heating your charge air even further right before it enters the charge cooler, but this is what BMW has done on the S58. This is done for emissions and quick warm-up purposes. However, If you are looking to make power on the S58, and are upgrading your charge cooler, or adding PI. While you are there, it takes 30 seconds to remove the coolant lines from the TB connections and replace them with our billet coolant delete kit. This completely removes the coolant from the Throttle body and provides a bypass for the coolant. Simply remove the two lines going to the throttle body, and run our hose in their place. You leave the coolant fittings on the TB open and avoid any unwanted heat being introduced into your charge tract. In our opinion a must for full effort builds. We take the work out of it for you. Kit included:
- One Plug and Play TB Coolant Delete Hose
- Billet 6061 Anodized coolant fittings for long leak-free life
- Reinforced 7-ply silicone hose for strength and longevity
- Vibration-resistant crimp clamps
- 100% plug and play, NO cutting or removing factory clamps or hoses. Fully reversible
-
Looking for Mac solenoids for your build? We got em here at VTT-FAB so you can get everything in one place. We have 3-port, and 4-port in stock!
-
We have a variety of fittings in stock to help you get your turbo system plumbed up! Available are:
- 1/8" NPT to -6 AN Male (Great for water lines, or anywhere you need a small 1/8" NPT to -6 Male AN)
- M14x1.5 to -6 AN Male (Great for water lines on Garrett turbos GT, GTX, and G-Series, or anything that has a metric M14x1.5 thread and you need a -6AN male)
- .035" Turbo feed restrictors. These are for Garrett turbochargers and will fit GT, GTX, and G- Series up to G35
- Garret GT, GTX, and G-Series up to G35 -8 An drain adapter. For those that want a low profile -8 drain for their GT-G-Series Garrett. (Comes with two bolts, and a gasket)
-
High-Boost Crankcase Ventilation Adapter for BMW Engines Building or running a high-boost, high-powered BMW engine? Boost increases crankcase pressure, which, if left unchecked, can lead to issues such as smoking, power loss, and even engine failure. Adequate venting is essential for optimal performance and engine health. These are designed to connect directly to S58/B58(TU) stock VC, or screw into ANY VTT Billet or Cast VC While some believe a -10AN vent is sufficient for these builds, the truth is: it’s not. To address this, we developed a larger, more effective solution for our builds—now available for everyone. Our Oil Cap adapter securely snaps in place, replacing your oil cap and providing a platform for a -16ORB fitting in a variety of configurations. Choose from -12AN to -20AN fittings, depending on your build’s needs. This cap is thicker than our low-profile option so care must be taken when planning hood clearance for the versatile venting options.
Key Features:
- Attractive Oil cap design
- Connects to stock S58/B58(TU) VC or VTT Billet/Cast VC
- Vented, comes with multi-hole venting to knock down large oil droplets before they make their way into the catch can system
- High-performance venting: Supports configurations from -12AN to -20AN fittings.
- Customizable: Compatible with various fittings to suit your build.
Important Notes:
- This kit requires you to supply your own hose, hose ends, and catch can to complete the system.
- Some fitting options may require 4–5 days for shipping, as we keep only select configurations in stock.
- Also fits other platforms such as B48, B46, Mini, etc. DOES NOT FIT Gen 1 B58
-
High-Boost Crankcase Ventilation Adapter for S58/B58 Engines Building or running a high-boost, high-powered S58 or B58 engine? Boost increases crankcase pressure, which, if left unchecked, can lead to issues such as smoking, power loss, and even engine failure. Adequate venting is essential for optimal performance and engine health. While some believe a -10AN vent is sufficient for these builds, the truth is: it’s not. To address this, we developed a larger, more effective solution for our builds—now available for everyone. Our low-profile adapter securely snaps in place, replacing your oil cap and providing a platform for a -16ORB fitting in a variety of configurations. Choose from -12AN to -20AN fittings, depending on your build’s needs. At just 10mm thick, this adapter maximizes hood clearance for versatile venting options.
Key Features:
- Low-profile design: Only 10mm thick for maximum hood clearance.
- High-performance venting: Supports configurations from -12AN to -20AN fittings.
- Customizable: Compatible with various fittings to suit your build.
Important Notes:
- This kit requires you to supply your own hose, hose ends, and catch can to complete the system.
- Some fitting options may require 4–5 days for shipping, as we keep only select configurations in stock.
- Also fits other platforms such as B48, B46, Mini, etc. DOES NOT FIT Gen 1 B58
-
VTT-FAB is proud to present the finest V-Band heat sinks available on the market. These heat sinks are designed to enhance your welding experience by efficiently dissipating heat away from the V-band flange, thereby minimizing or eliminating warping and pulling.Crafted from 100% billet-machined 6061-T6 aluminum, these V-bands feature precisely machined fins that facilitate rapid heat release. Additionally, they are equipped with dual 1/8" NPT ports on both the top and bottom, with the interior port incorporating a built-in diffuser to ensure optimal gas flow during back purging.Our V-Band heat sinks are available in a range of sizes, including 2", 3.5", 3", and 4", as well as various types to accommodate different V-bands.Features:
- - 100% billet-machined from 6061-T6 aluminum
- - Dual 1/8" NPT ports on top and bottom
- - Built-in diffuser for perfect gas flow during back purging
- - Available in various sizes and styles
SEE BELOW FOR FULL FITMENT SPECS
-
Fabbing up a custom single turbo or twin turbo kit that requires a custom water neck adapter to clear. We got you covered. These are machined from billet 6061-T6 and come in raw aluminum for easy welding.
