-
Sale!
VTT Billet Check Valves
$24.99 – $29.99VTT CNC Billet check valve that can be used for a variety of uses including a vacuum/boost check valve when removing the stock PCV system, and still wanting to run vacuum to the crankcase. Rated at over 100 psi, with a cracking psi of .25psi. -
VTT Ignition Coil Kits
$159.99 – $209.99VTT is proud to offer ignition coil replacements for the N5X platforms, as well as B5X, and many VAG platforms. We started our quest for coils by contacting multiple coil manufacturing companies, paying for individual coils to be made then putting them through rigorous testing in the USA to ensure they matched or exceeded factory output. Once we were satisfied with the testing, we had the best performing coils made to our colors and specs. We offer these coils as complete sets for the N54, B58/S58, and the VAG platforms in either 4, or 5 cylinders. We also offer upgraded plugs which are highly recommended to change when doing coil replacements These coils come in 3 colors, Red, Black, and Blue, and are not simply an aesthetic upgrade but match or exceed the factory secondary spark energy. The VAG coil, is extremely potent, and the tester was so impressed with it compared to the factory coil, he called it a "BEAST" of a coilNote: To extract maximum performance from VTT coils minor tune changes are required to optimize dwell periods. See recommended Dwell times below
-
Sale!
VTT B58TU A90/91 Supra One Way Crankcase Breather
$129.00$119.99VTT B58 A90/91 Supra Billet One Way Crankcase Breather
VTT is happy to introduce the first and only available plug-and-play ONE-WAY crankcase breather kit for BMW B58TU A90/91 Supra applications. The B58 engine is known for poor PCV and crankcase pressure issues. With this breather simply remove your oil cap, install the breather, and instantly free up horsepower, improve turbo draining, remove crankcase pressure, all while adding a cool look to your engine bay. FITS with the engine cover on. Engine cover can be removed, and installed without removing the breather. -
NGK 94201 Spark plug set for all S58/B58/48 applications, and ALSO for N54/55 running the new B58 coil upgrade. We recommend these for running 100% e85, and high boost on many BMW applications including N54, N55, S55, if you upgrade to the B58 coils. These are also great maintenance replacements for your S58/B58/48 powered vehicle at a much better price than most. Plugs can be bought as a set of 6. You can add pre-gapping for an additional $25
-
Replacement Gasket for VTT Valve Covers
$29.99 – $64.99Need to replace the gasket on your VTT Aluminum VC? Simply choose your model from the dropdowns to ensure you get the correct version. -
VTT Billet Crankcase Breather replacement filter
$19.99 – $24.99Need a replacement filter for your VTT Billet Crankcase breather? You can order on here. We offer them in 3 heights, low 48mm, medium58mm, and tall 68mm. This is measured from base to top. The filter will include a new clamp. For reference: N54/55 mostly use the low A90 Supra use Medium Most Audi applications can fit a tall, but measure your filter before ordering. -
VTT is proud to offer a Titanium hardware upgrade for all our Billet and Cast VC's. This will come with M6x30 Ti bolts N54 /N55/S55/B58 Gen 1/ B58 TU it will be an Umbrella head with a 16.3mm head. These bolts weigh half as much as comparable steel hardware and look amazing. Colors to choose from will be Burnt, Black, and Natural (silver)
-
VTT Reinforced Universal Silicone Hoses
$9.99 – $14.99VTT offers silicone hoses in various Push-lock sizes, we use these for our catch can kits, but they are also suitable for coolant, vacuum, boost, etc. Do not use with fuel. We offer: -10 Push Lock 24", and 18" -8 Push Lock 24", and 19.5" -6 Push Lock 24" -
VTA Breather
$39.99Not available for single can external PCV Valve. -
VTT Billet BMW B58 Vacuum/Boost Adapter
$49.99 – $64.99We are happy to release our BMWB58 (Fits ALL B58 models including TU found in the A90/A91 Toyota Supra) vacuum/boost adapter. These go inline with the intake manifold fitting and provide a full boost/vacuum signal from the manifold. This fitting adds two 1/8NPT bungs to accept any fitting that has 1/8" NPT threads. You can choose options, Fitting by itself, 1/4" barb, as well as 1/8NPT plugs if you only want one barb, etc. You can choose straight or 90-degree barbs. Once installed it tucks perfectly under your engine cover. These are perfect for running your PI switch off manifold pressure which is much more accurate than charge pipe, and they are also great for BOV running the proper size line without having to drill a hole in your manifold. These do space out any sensors etc giving inaccurate readings like some of the other brands do. They are made from 6061-T6 anodized black, with steel plugs, and Blue Anodized barbed fittings. You can choose to order in a few ways. Adapter alone - $40 Basic kit - 1 Adapter, 1 barb, and one plug $45.00 Dual Barb kit - 1 Adapter, 2 barbs, $55.00 -
VTT is proud to offer our "OBD-LOCK" OBD port locking tool. This tool is made from billet 6061-T6 aluminum and is designed to completely lock out your OBD port from being accessed. This is useful for people who do not want dealers, techs, etc from accessing their OBD port, and possibly changing a tune, etc. This is also perfect for anti-theft prevention as it will not allow a would-be thief to hook up to the car's OBD port, duplicate a key, etc. The OBD-LOCK cannot be removed without physically destroying the OBD port if you do not have the proper tools. VTT uses 5 types of screw head designs for every 200 OBD-LOCKS made. This means that worldwide only 40 OBD-LOCKS are using the same head design. For each batch of 200, we redesign the screw heads meaning every batch of 200 OBD-LOCKS will use different screw heads and tools. Each OBD-LOCK sent has its head design chosen at random. After Extensive testing, we have found that our OBD lock fits EVERY SINGLE OBD port we have tried, this means it will fit every single OBD port currently on the market from a high-end BMW to a Ford F150 diesel. If you order one, and find it does not fit, PLEASE let us know.
FITMENT: We have TWO versions one for ALL GM vehicles and one for ALL NON-GM Vehicles. Please order the one you
-
VTT-FAB Billet Oil/Coolant Fittings, and block offs
$20.00 – $40.00Looking to fab your own turbo kit for BMW platforms, and need an easy solution to block off water lines, or create feed and drain fittings. Look no further, we offer a wide range of oil/coolant fitting options for most late-model BMW platforms. See the Full description below for a full part number breakdown -
Do you work on a lot of BMW engines from various platforms? Tired of having to adjust universal engine stand plates to fit your engine? Hate not having access to the flywheel end with the engine on the stand? We answered yes to all of those things, we made a tool for anyone that works on BMWs often, and wanted a strong bolt-on engine stand plate that keeps the flywheel end of the engine open! These engine stand plates are machined from a solid billet of 6061-T6 aluminum and anodized in 5 colors for long-lasting corrosion resistance. The engine stand plates currently fit the following engines, N54, N55, S55, B58, S58 with more to come! These are lightweight, and rated for over 1200 lbs! Key Features:
- Lightweight and strong billet 6061-T6, anodized for a long-lasting finish
- Direct bolt on to the intake side motor mount location
- Clears all accessories when installed for easy engine assembly when on stand INCLUDING flywheel or flex plate
- Provisions for location pin, and bar to spin the engine on the stand
-
Sale!
VTT-FAB M7 Copper Locking Exhaust Nuts
$3.00$1.49Are you building a single kit for the N54, N55, or S55 platform? M7 Locking exhaust nuts is not easy. So we made our own to combat the issue. These are the perfect solution to the problem of hard-to-find M7 lock nuts. Sold individually so order the number you need.Note: This is nuts ONLY Stud not included, by our extended M7 studs here - https://vargasturbo.com/product/vtt-fab-extended-m7-n54-n55-s55-b58-2-port-head-studs/
-
Soft bushings are the enemy of launching hard, and keeping your drivetrain together. The BMW Transfer Case bushings are notoriously soft, and that is the opposite of what you want when launching a car hard. You can replace the bushing with a solid one, but this is time-consuming usually requires lowering or removing the transfer case, and results in a lot of added NVH. The best path is simply to reduce the amount of flex of the factory bushing so you keep the nice manners when cruising around town, and at idle, but when its time to the launch the transfer case cannot move as it could without the insert. These come as a set of two with 2 bolts to keep them in place. Install time once you get to them is about 2-3 minutes. Could not be easier. Put some lube on them, push them in, and tighten the screws. These are a MUST for high-power G8X, and F9X X3/X4M Builds. All platforms they fit are below. Features:
- 6061- T6 aluminum construction
- Easy to install
- Fully reversible
- Do not add NVH
-
Looking to make sure all metal contaminates that are possibly in your oil are not circulated? VTT has you covered with our Titanium Magnetic oil drain plugs for BMW, and any other vehicle that uses an M12x1.5 drain plug. This drain plug will capture any ferrous metal particles in your oil, and capture them to be cleaned during your next oil change. It also is stronger than a Steel or Aluminum drain plug, and looks cool! These are made from GR5 Titanium and use a rare earth magnet to capture metal particles in your oil... Kit includes:
- 1 Titanium Drain Plug
- 1 M12 Crush Washer
-
VTT Carbon Fiber Dragy Holder
$19.99 – $49.00Tired of your Dragy flying all over the car as you try to do runs? Tired of low sats or no sats warning due to improper location of the Dragy in the vehicle? Well say goodbye to those issues with our new Carbon Fiber and Plastic Dragy holders. These are made from either 100% Pre-Preg Carbon Fiber, or molded plastic for a perfect fit. The carbon fiber gives it just the right look to add to your performance vehicle! Each holder has dual Suction cups and will stick to any smooth surface. We suggest mounting them in the upper left or right corner of your windshield with a full view of the sky. Dragy holder features- Stop your Dragy from flying off the dash, and having to search for it
- Position your Dragy in the optimal position for the best satellite coverage
- VTT Dragy holder exposes the entire top of the Dragy so nothing is blocking the receiver from the Satellite
- The charging port is not blocked and can be accessed with the cover on
- Choose from REAL Carbon Fiber or Molded Plastic
-
Sale!
VTT A90/91 Supra Engine Catch Can
$399.99$349.99VTT is proud to announce our A90/91 Supra engine catch can set up. This kit uses our already extremely popular modular catch can, and couples it with a custom CNC 6061 bracket, VTT CNC banjo fittings, VTT 5 ply silicone hose, and Push lock fittings. Install is simple, takes about 30 minutes to 2 hours depending on your skill level, and requires removing one factory hose to install the VTT hoses. Giving an OEM fit and finished when installed This catch can fits all known intake variations we have seen, including stock intake. Kit Break down is as follows:- One Catch Can
- One CNC 6061 bracket
- Two -10 Low Profile CNC Banjo Fittings
- Two -10 VTT 5-Ply silicone Vacuum hoses
- Two -10 Push Lock Fittings
- Two spring clamps
- Available with an optional Drain fitting, allowing quick draining
-
VTT is proud to offer our billet replacement for the BMW B58 factory plastic Oil filter housing cap. This cap does away with the weak plastic cap while adding a strong magnet to pull metal from the oil, and some pop/color to your engine bay. These oil filter housing caps retain ALL of the factory provisions for the filter basket, including the lower pins which are important for the proper function of pressure bypass, etc. We offer these caps in 4 anodized colors - Red, Black, Blue, and Clear
-
Sale!
VTT B58 Engine Lifting hook
$15.99$14.99Need to work on the B58 engine outside of the car? Lift it to put on an engine stand etc? BMW makes an engine lifting tab but it costs $25, and they do not always have them in stock. We made our own, to avoid the high cost, and possibly long wait time. The perfect tool when you want to lift the engine balanced in the place BMW designed for it to be lifted. Made out of coated steel for high strength, long life, and corrosion resistance. Fits all B58 models, and possibly S58 -
Sale!Are you building a single kit for the N54, N55, or S55 platform? The stock studs are usually a little bit short for most single-head flanges, and finding M7 studs is not easy. So we made our own longer studs to combat the issue. Made from 10.9 grade steel, and coated in black oxide, these are the perfect solution to the short stud problem. Sold individually so order the number you need. Stud details are as follows
- Overall length 47mm (stock 39mm)
- 3mm shoulder
- 6mm head which is 5mm hex
- 14mm short end
- 24mm long end (stock 15mm)
Dont forget our M7 copper lock nuts as well to complete the job - https://vargasturbo.com/product/vtt-fab-m7-copper-locking-exhaust-nuts/
-
Toyota Supra A90/91 Carbon Fiber Strut Braces
$269.99 – $319.99We took our popular Billet G8X strut bars and redesigned them for use on the A90/91 Supra. No metal with ugly carbon overlay. This is a real carbon fiber strut bar with ends are CNC machined from 6061-T6 aluminum or T2 Titanium, and anodized in Black, Red, Blue, or genuine T2 Titanium with a rainbow finish. -
Improve engine/shifting feel without a huge increase in NVH or high cost! VTT A9X billet motor mount inserts upgrade mounts the way BMW does it, allowing a minimal increase in NVH while stiffening up the engine/shifting feel, and getting rid of excessive engine movement
-
Looking to go above 45 psi in your BMW-powered vehicle? Looking for a plug-and-play solution? We have you covered with our BMW 5 bar sensor. These will allow 58 psi to be read and are factory plug, and play. Simply remove your old sensor, replace it with the 5 bar, and have your tuner rescale your map values in both your DME tune and your PI tune if applicable. These are GENUINE BMW sensors directly from BMW.
-
The Factory B58 TU water neck is plastic and is right in the path of your charge pipe if you lose a connection and it blows off. If this does happen to you it can break the plastic neck emptying your coolant in seconds causing you in the best-case scenario to be stranded, and in the worst-case scenario expensive engine damage. Add some cheap insurance with our Billet Water neck.
-
Tired of getting off the dyno, and having your drivetrain malfunction light on due to a broken plastic ride height bracket? So were we, after we broke 3 of them, we knew it was time to make our own to combat the issue. This bracket is cut from 6061-T6 for strength and anodized black for a long-lasting finish.
-
Show off your VTT support and get a good laugh from people with our "We Like To Party" License plate bracket. Born from the infamous quote in Talladega nights
