-
A90/91 Supra / G – Series BMW “GC” Front Drag Brake Kit
$1,219.99 – $1,849.99Looking to make your A90/91 Supra faster in the 1/4 mile or 1/2 mile racing? Want to run 17", (or 15" wheels with suspension modifications), and skinnies in the front? Want to drop OVER 70lbs of unsprung weight off the front of the car at the same time? Do not want to break the bank while doing so? Look no further than the VTT "GC" Front Drag kit for the A90/91 Toyota Supra. This kit will allow you to run the wheel/tire combo you need to drop your ET's all while putting the car on a significant diet over the stock front brake set up. The kit is a true plug-and-play kit using Genuine Wilwood parts, coupled with DOT-approved brake lines, CNC 7075 rotor hats/brackets, and a CEL eliminator harness for the brake sensor. This kit comes in 2 different variations, with two different caliper sizes for each Fits all 2020+ Supra, and some G-Series BMW. We have confirmed fitment on M340iDisclaimer: The HD kits are designed for street use, and drag racing. Never use for heavy braking racing environments such as Auto-X or Road Racing. Scalloped kits should never be used for street driving, and are ONE-PASS COOL DOWN DRAG RACING ONLY, EVEN IN THIS ENVIRONMENT, THEY MAY CRACK IF USED TOO AGGRESSIVELY. Always drive within your limits!
-
A90/91 Supra / G – Series BMW “GC” Rear Drag Brake Kit
$1,219.99 – $1,329.99Looking to make your A90/91 Supra faster in the 1/4 mile or 1/2 mile racing? Want to run 17", or 15" wheels with a very minor suspension modification? Want to drop 43lbs of unsprung weight off the Rear of the car at the same time? Do not want to break the bank while doing so? Look no further than the VTT "GC" Rear Drag kit for the A90/91 Toyota Supra. This kit will allow you to run the wheel/tire combo you need to drop your ET's all while putting the car on a significant diet over the stock rear brake set up. Fits all 2020+ Supra, and some G-Series BMW. We have confirmed fitment on M340i -
Improve engine/shifting feel without a huge increase in NVH or high cost! VTT A9X billet motor mount inserts upgrade mounts the way BMW does it, allowing a minimal increase in NVH while stiffening up the engine/shifting feel, and getting rid of excessive engine movement
-
B58 CP-CARRILLO CONNECTING ROD, SET (6)
$1,739.99 – $2,209.99Carrillo connecting rods are well known within pro racing and street performance circles for good reason; they produce a premium product that winning racers around the world depend on. -
B58 CP-CARRILLO FORGED PISTON SET
$1,419.99 – $1,469.99These are the same premium pistons we use in our winning race and high-performance street engines around the world! We feel that these are the best pistons for your high performance or racing engine. -
The Factory B58 TU water neck is plastic and is right in the path of your charge pipe if you lose a connection and it blows off. If this does happen to you it can break the plastic neck emptying your coolant in seconds causing you in the best-case scenario to be stranded, and in the worst-case scenario expensive engine damage. Add some cheap insurance with our Billet Water neck.
-
The Factory B58 TU Upper Cylinder head hose is plastic and is right in the path of your charge pipe if you lose a connection and it blows off. If this does happen to you it can break the plastic neck emptying your coolant in seconds causing you in the best-case scenario to be stranded, and in the worst-case scenario expensive engine damage. Add some cheap insurance with our Billet Upper Cylinder head hose, this sits right above the plastic water neck. Product Details:
- Plug and play direct factory replacement
- 6061-T6 Billet aluminum with black anodizing for a corrosion-free life
- 7-Ply Silicone in 3 colors
- Cheap insurance against a blown charge pipe which could turn into a blown motor
-
Sale!
BMW Factory OEM EWG Actuator Replacement – 11 65 8 691 853
$499.00$349.00Looking to replace your damaged factory BMW Actuator part number - 11658691853 VTT has located and ordered in bulk these actuators, and offer them at a discounted price. These are 100% FACTORY BMW OEM actuators, not aftermarket. Fitment is for the following, but they work to replace basically any BMW Actuator. -
Sale!
BMW/Toyota 5×112 to 5×114 Bolt Pattern Conversion Kits
$69.99 – $129.99Looking to convert your 5x112 M14x1.25 vehicle such as A90/91 Toyota Supra, and 2020+ BMW G-series to 5x114 to open up your wheel options? We got covered with our VTT wheel stud conversion kits. These kits are forged cold-rolled steel in 10.9 class, with corrosion-resistant coating for years of use, and convert your vehicle to M12x1.50 wheel studs which allow you to fit 5x114 wheels with no other changes.PLEASE NOTE – THESE STUDS WILL ONLY WORK IF YOUR WHEELS ARE DRILLED M14 THESE WILL NOT WORK FOR WHEELS DRILLED M12!
DO NOT USE ANY HUB-CENTERING SLEEVES WITH THESE CONVERSION STUDS, THE LUGS WILL CENTER THE WHEELS. THE USE OF A CENTERING SLEEVE MAY LEAD TO STUDS BREAKING. FOR INSTALLATION YOU MUST SNUG EACH LUG UP SLOWLY, AND IN A STAR PATTERN TO GET THE WHEEL CENTERED ON THE LUGS, FAILURE TO DO SO CAN ALSO LEAD TO FAILURE.
-
Sale!
BMW/Toyota M14x1.25 to M14x1.50 Wheel Stud conversion Kits
$69.99 – $129.99Looking to convert your Supra or G Series BMW to wheel studs. Want to get rid of the difficult to find M14x1.25 ultra-fine thread and convert it to M14x1.15? We got covered with our VTT wheel stud conversion kits. These kits are forged cold rolled steel in 10.9 class, with corrosion-resistant coating for years of use, and convert your M14x1.25 vehicle to M14x1.50 wheel studs. -
Unsure of the state of your CHRA's, whether brand new from a questionable source or rebuilt? DON'T install them without having a proper High-Speed balance done! This is the #1 most critical factor when building a turbocharger, and is even more important for performance turbochargers or small twins that see a LOT of RPM. We use a Turbo Technics VS3 balancer, and balance most units down to under .5G Not all turbos will be able to pass a high-speed balancing test for any number of reasons (usually poor assembly, bent shaft, etc), if they will not pass, we will send you the specs they are in, and as close as we could get them. We then will give you the option to send them back, or we can disassemble, and rebuild them in-house using our other balancing, and assembly tools to ensure a properly built/balanced unit. The service is $79.99 each for most turbos, and we have the capabilities to balance most units. If sending in twins please choose TWO as the quantity
UNITS MUST BE SENT IN WITH NO HOUSINGS, AND IN A CONDITION READY TO BE BALANCED, IF YOU NEED TO SEND IN COMPLETE TURBOS, WE CAN DISASSEMBLE, AND BALANCE FOR YOU, BUT AN EXTRA CHARGE WILL APPLY. IF THE UNITS ARE SENT IN A CONDITION WHERE THEY CAN NOT BE BALANCED WE WILL LET YOU KNOW THE PRICE TO GET THEM TO A STATE WHERE THEY CAN BE
-
NGK 94201 Spark plug set for all S58/B58/48 applications, and ALSO for N54/55 running the new B58 coil upgrade. We recommend these for running 100% e85, and high boost on many BMW applications including N54, N55, S55, if you upgrade to the B58 coils. These are also great maintenance replacements for your S58/B58/48 powered vehicle at a much better price than most. Plugs can be bought as a set of 6. You can add pre-gapping for an additional $25
-
PFS is proud to offer a true drop-in 800-1000WHP+ capable LPFP for A90/91 Toyota Supras. This LPFP needs NO additional pumps, wiring harnesses, etc etc. It will support up to 800WHP on Ethanol percentages as high as E98 and will support much higher power levels with less E content as long as you have the octane to support it. For the pump, we start with a factory bucket, we modify it extensively to accept our custom PFS Brushless fuel pump. We then re-terminate the factory wiring to accept the new pump. No wiring splices, done the same way the factory does -the right way.
-
PFS B58 Port Injection Kit
$689.99 – $2,299.99Looking for some more fuel for your B58 powered BMW? Not looking to break the bank on overpriced PI kits? PFS has you covered with its Plug, and play PI kit for the B58. -
PFS Supra upgraded LPFP Line
$89.99VTT is proud to offer the PFS A90/91 Supra upgraded LPFP line. This line replaces the factory line from the tank to the hard-line under the drivers feet with a line which increases diameter 22%, and volume/area 56% over factory line. The factory line is just under 8mm ID the PFS line uses genuine Parker 801-6 hose which is 10mm ID. This is a plug-and-play option. Remove your factory line, and install this line in its place, it will fit in all the line holders. -
PTE – Precision Turbochargers
$2,234.49 – $4,428.99VTT is proud to offer PTE Turbocharger products! -
Replacement Gasket for VTT Valve Covers
$29.99 – $64.99Need to replace the gasket on your VTT Aluminum VC? Simply choose your model from the dropdowns to ensure you get the correct version. -
Skunk 2 B58 TU Camshafts
$1,545.00Skunk2 Ultra Series Stage 1 Camshafts for Toyota Supra MK5/BMW B58TU /// FEATURES • Billet 8660 Alloy Steel Camshafts • Improved Efficiency/Power • Widest Possible Power Band • Smooth Driveability & Idle • Retains Double VANOS + Valvetronic Functionality -
Sale!
TOYOTA B58B30 STROKER KITS
$7,229.99 – $7,559.99VTT Is proud to offer the BC stroker kit for the Toyota B58B30 engine platform that incorporates a 100mm stroke, steel billet crank, BC 4340 Pro Series Heavy-Duty connecting rods rated to 1600+ horsepower. -
Toyota Supra A90/91 Carbon Fiber Strut Braces
$269.99 – $319.99We took our popular Billet G8X strut bars and redesigned them for use on the A90/91 Supra. No metal with ugly carbon overlay. This is a real carbon fiber strut bar with ends are CNC machined from 6061-T6 aluminum or T2 Titanium, and anodized in Black, Red, Blue, or genuine T2 Titanium with a rainbow finish. -
VTA Breather
$39.99Not available for single can external PCV Valve. -
VTT “DCS” EWG System for TurboSmart Straight Gates
$799.99 – $1,499.99VTT is proud to offer our EWG "Direct Control System" or DCS! This is a completely new innovation for people looking to control the highest-flowing wastegate on the market using an existing BMW electronic actuator. This system will allow BMW owners who have a vehicle with Electronic Wastegates from the factory to utilize this system to control an externally wastegated turbo system, AND it will ALSO allow ANY vehicle to use this setup to control your own custom turbo system. This is done by utilizing our custom 7075 Billet aluminum bracket coupled with a Turbosmart Straight gate, and if needed an EWG controller made for us by DCCD Pro. This allows direct external wastegate control over any turbocharger system with or without EWG for the factory. Features:- Utilizes the most current wastegate technology the Turbosmart Straight Gate. This gate allows maximum flow with minimal restriction, low drive pressure, and much more. Full details can be found here - https://www.turbosmart.com/product/electronic-straightgate-esg50-external-wastegate/
- Can be configured in multiple ways, and angles based on how you mount the adapter
- The adapter is 7075 Aluminum which has the strength of steel and weight of aluminum
- All connection fittings, are made from Nitronic 60 which has extremely high temperature and wear properties
- Zero Drive Pressure, no springs, no poppet valves, direct control over the gate using factory ECU logic
- Adaptable to ANY turbo system on any car to provide the ultimate in boost control!
-
VTT is proud to offer our "OBD-LOCK" OBD port locking tool. This tool is made from billet 6061-T6 aluminum and is designed to completely lock out your OBD port from being accessed. This is useful for people who do not want dealers, techs, etc from accessing their OBD port, and possibly changing a tune, etc. This is also perfect for anti-theft prevention as it will not allow a would-be thief to hook up to the car's OBD port, duplicate a key, etc. The OBD-LOCK cannot be removed without physically destroying the OBD port if you do not have the proper tools. VTT uses 5 types of screw head designs for every 200 OBD-LOCKS made. This means that worldwide only 40 OBD-LOCKS are using the same head design. For each batch of 200, we redesign the screw heads meaning every batch of 200 OBD-LOCKS will use different screw heads and tools. Each OBD-LOCK sent has its head design chosen at random. After Extensive testing, we have found that our OBD lock fits EVERY SINGLE OBD port we have tried, this means it will fit every single OBD port currently on the market from a high-end BMW to a Ford F150 diesel. If you order one, and find it does not fit, PLEASE let us know.
FITMENT: We have TWO versions one for ALL GM vehicles and one for ALL NON-GM Vehicles. Please order the one you
-
Show off your VTT support and get a good laugh from people with our "We Like To Party" License plate bracket. Born from the infamous quote in Talladega nights
-
Looking to protect your single turbo investment, dont have a ton of room, and need a low profile filter that can flow what you need? VTT Has you covered with our Low Profile Single turbo Air Filters. These filters are custom-made for VTT. They are made with a heat-resistant silicone base, and a high-flowing cotton weave element with a pre-oiled design to catch contaminates but allow free flow. We currently offer them in Black, and 3 flange sizes. 3", 4" and 5" flange. With two filter heights. Tested at over 1200WHP with no loss of power observed. Filter Options - Offered in White, and Black with the following dimensions Short - 3.75" Tall, 7.5" OD Large end, 5" Small end 3", 4", or 5" Flange Tall - 4.5" Tall, 7.5" OD Large end, 5" Small end 3", 4", or 5" Flange
