-
VTT CNC Billet check valve that can be used for a variety of uses including a vacuum/boost check valve when removing the stock PCV system, and still wanting to run vacuum to the crankcase. Rated at over 100 psi, with a cracking psi of .25psi.
-
VTT/PFS Stainless Steel Fuel Strainer for Walbro In-Tank Pumps
The fuel system is one of the most critical components of your entire build—it delivers the fuel that translates into big power and fast times! Without proper filtration, your Walbro 274, 285, or 295 fuel pump can ingest contaminants, leading to premature failure. However, choosing the right strainer or pre-filter is just as important as post-filtration. 🚨 Why Does Your Fuel Pump Need the Right Strainer? ✅ Too fine of a filter can restrict flow and cause the inlet to collapse. ✅ Too coarse of a filter can allow debris to pass through, damaging the pump and engine. ✅ Low-quality materials can break down, collapse, or cause fueling issues—leading to potential engine failure.The VTT/PFS Stainless Steel Fuel Strainer – The Ultimate Solution
-
Need a Tee fitting for plumbing Vacuum, or Boost lines, Don't want to use cheap plastic ones that can get soft when hard, and brittle after they heat cycle? We didn't either, which is why we machined these high-quality billet tees to solve this issue. Machine from 6061-T6 aluminum, and anodized in black for a long-lasting corrosion-free finish, these tees look great, and will you never have to worry about one failing. We offer them in two sizes, each size has 12mm legs and 3 barbs:
- 7.60mm / -4 Push Lock for people looking to use -4 push lock hose or -4 AN hose. This is a perfect fit for those.
- 1/4" For people looking to use 1/4" vacuum tube
-
Tired of your Dragy flying all over the car as you try to do runs? Tired of low sats or no sats warning due to improper location of the Dragy in the vehicle? Well say goodbye to those issues with our new Carbon Fiber and Plastic Dragy holders. These are made from either 100% Pre-Preg Carbon Fiber, or molded plastic for a perfect fit. The carbon fiber gives it just the right look to add to your performance vehicle! Each holder has dual Suction cups and will stick to any smooth surface. We suggest mounting them in the upper left or right corner of your windshield with a full view of the sky. Dragy holder features
- Stop your Dragy from flying off the dash, and having to search for it
- Position your Dragy in the optimal position for the best satellite coverage
- VTT Dragy holder exposes the entire top of the Dragy so nothing is blocking the receiver from the Satellite
- The charging port is not blocked and can be accessed with the cover on
- Choose from REAL Carbon Fiber or Molded Plastic
-
VTT is happy to offer our very unique and universal billet mount to fit any roll bar or cage with 1.5", 1.75", or 2" diameter tubing. These mounts are designed from 6061-T6 aluminum and are made to SECURELY hold a JBL Flip version 3 - Version 6 and allows you to bring music into your race car, off-road vehicle, rock crawler, boat, basically anything that has a length of tubing this will allow you to have an easy way to have tunes without having to install and mount a stereo system. They can also be used as a single mount to hold things such as a helmet, steering wheel, or anything you want to quickly hang for easy access once seated. For the JBL flip you will need TWO mounts, simply install them loosely, snap in your JBL Flip to get the proper spacing, and tighten down. The device is then securely mounted and can be removed easily. We offer these in a variety of anodized colors for a long-lasting durable finish including Black, Red, Blue, Clear, Orange, and Green Mounts are sold individually Features:
- Billet 6061-T6 Aluminum construction anodized in a variety of colors
- Can be used to SECURELY mount a JBL Flip 3-6 to anything that has a length of 1.5", 1.75" or 2" tubing
- Can also be used as a universal mount for anything you need to hang in your race car, off-road vehicle, etc
- Completely reversible, and can be moved from vehicle to vehicle
-
Unsure of the state of your CHRA's, whether brand new from a questionable source or rebuilt? Don't install them without having a proper High-Speed balance done! This is the #1 most critical factor when building a turbocharger, and is even more important for performance turbochargers or small twins that see a LOT of RPM. We use a Turbo Technics VS3 balancer, and balance most units down to under .5G Not all turbos will be able to pass a high-speed balancing test for any number of reasons (usually poor assembly, bent shaft, etc), if they will not pass, we will send you the specs they are in, and as close as we could get them. We then will give you the option to send them back, or we can disassemble, and rebuild them in-house using our other balancing, and assembly tools to ensure a properly built/balanced unit. The service is for most turbos, and we have the capability to balance most units, NOT ALL. If sending in twins please choose TWO as the quantity
UNITS MUST BE SENT IN WITH NO HOUSINGS, AND IN A CONDITION READY TO BE BALANCED, IF YOU NEED TO SEND IN COMPLETE TURBOS, WE CAN DISASSEMBLE, AND BALANCE FOR YOU, BUT AN EXTRA CHARGE WILL APPLY. IF THE UNITS ARE SENT IN A CONDITION WHERE THEY CAN NOT BE BALANCED WE WILL LET YOU KNOW THE PRICE TO GET THEM TO A STATE WHERE THEY CAN BE
-
Please Note: This is a Virtual Gift Card. After purchase you will receive an email with your Gift Card code
-
VTT -16 Billet HIGH-FLOW Catch Can System
Maximum Venting for Maximum Power
VTT is proud to introduce our -16 Billet High-Flow Catch Can System — designed from the ground up for high-horsepower applications requiring serious crankcase ventilation. Whether you're pushing over 900WHP or beyond 2000WHP, this system delivers unmatched performance, reliability, and engine bay cleanliness.
Key Features:
-
Supports -16 AN lines (with optional -12 or -20 fittings)
- 20 Fluid OZ capacity
-
Engineered for big-power builds needing high crankcase pressure relief
-
Triple-stage filtration system to eliminate oil mist — even in the event of engine failure
-
Designed, tested, and proven to keep oil inside the catch can — not in your engine bay
Triple Filtration Technology:
-
Stage 1 - Stainless steel filter – captures 95% of oil mist on entry
-
Stage 2 - Perforated diffuser plate – further disperses and slows down airflow
-
Stage 3 - Final stainless mesh layer – scrubs out any remaining vapor before venting
This advanced system has been tested with over 200 PSI of pressure and more than half a quart of oil without releasing a trace of oil mist. As long as the catch can is properly serviced and not overfilled, even catastrophic engine failure won’t result in a mess under your hood.
Application-Specific Kits Available:
We offer plug-and-play kits for popular platforms, including:
-
G8X M2/M3/M4 (S58) SINGLE TURBO ONLY
-
F9X X3M/X4M SINGLE SINGLE TURBO ONLY
-
A9X Toyota Supra
Each Plug and play kit includes everything needed for installation: catch can, vehicle-specific bracket, fittings, hoses, and optional drain. Again, plug-and-play kits include ALL required parts. Bracket, fittings, line, etc. No additional fittings are required except the drain if wanted.
-
-
Give the Gift of VTT! Looking to get your friends, or family some go-fast parts, and no idea what they need, only that they love VTT? Well, our Gift Cards have you covered! They come in $50, $100, $250, $500, and $1000 increments. Each gift card is precision cut out of plastic in the shape of the VTT logo and has the dollar amount and the code on the back. Each gift code is unique and is locked to that card. To redeem simply enter the code during check out it will remove that amount, and if you have any leftover it will go back to the card.
You can choose to have your card physically mailed to you, or a virtual card where we can send you a scan of your card.
