-
Introducing the VTT OBD-LOCK – Enhanced Security & Improved Design!
We are excited to announce our OBD-LOCK! This latest version has been completely redesigned for improved strength, ease of installation, and enhanced protection. Key upgrades include:
No more OBD port penetration – eliminates any risk of damage
Revised thread style – prevents stripping for a secure fit
Stronger, more durable design – ensures maximum securityUltimate OBD Port Protection
The VTT OBD-LOCK is precision-machined from billet 6061-T6 aluminum and is engineered to completely lock out your OBD port, preventing unauthorized access.
Anti-Theft Protection – Prevents thieves from accessing the OBD port to duplicate keys or disable security systems
Dealer/Tech Lockout – Stops unauthorized tune changes or system modifications
Tamper-Proof Design – Cannot be removed without physically destroying the OBD port unless the correct tool is usedVTT OBD-LOCK – Version 2 NON-GM
Universal Fit for All Non-GM (General Motors) VehiclesThis device is compatible with all non-GM vehicles, including but not limited to:
-
All VAG group vehicles (VW, Audi, Bentley, etc.) — including recessed port VW/Audi models
-
Ford, Nissan, Honda, Toyota, Porsche, Dodge, Ram, Jeep, Kia, Subaru, and more
Not compatible with GM (General Motors) vehicles.
VTT OBD-LOCK – Version 2 GM
Universal Fit for GM (General Motors) Vehicles ONLYThis version is specifically designed for General Motors vehicles, including GM, Chevrolet, Cadillac, Holden, and other GM-branded models.
If your vehicle is anything other than a General Motors product, you will need the Non-GM version.
-
-
VTT/PFS Stainless Steel Fuel Strainer for Walbro In-Tank Pumps
The fuel system is one of the most critical components of your entire build—it delivers the fuel that translates into big power and fast times! Without proper filtration, your Walbro 274, 285, or 295 fuel pump can ingest contaminants, leading to premature failure. However, choosing the right strainer or pre-filter is just as important as post-filtration. 🚨 Why Does Your Fuel Pump Need the Right Strainer? ✅ Too fine of a filter can restrict flow and cause the inlet to collapse. ✅ Too coarse of a filter can allow debris to pass through, damaging the pump and engine. ✅ Low-quality materials can break down, collapse, or cause fueling issues—leading to potential engine failure.The VTT/PFS Stainless Steel Fuel Strainer – The Ultimate Solution
-
Building a kit using Mac solenoids to control boost? Need an easy way to mount it? VTT-FAB has you covered with our billet Mac Solenoid brackets. Machined from 6061 billet and anodized in 3 colors, these are the perfect way to mount your Mac valve and look good while doing it. Each kit includes:
- One Mac Solenoid bracket (3-Port or 4-Port)
- 2 Allen screws to hold the valve to the bracket
- M6 Mounting Bolt
-
Need a Tee fitting for plumbing Vacuum, or Boost lines, Don't want to use cheap plastic ones that can get soft when hard, and brittle after they heat cycle? We didn't either, which is why we machined these high-quality billet tees to solve this issue. Machine from 6061-T6 aluminum, and anodized in black for a long-lasting corrosion-free finish, these tees look great, and will you never have to worry about one failing. We offer them in two sizes, each size has 12mm legs and 3 barbs:
- 7.60mm / -4 Push Lock for people looking to use -4 push lock hose or -4 AN hose. This is a perfect fit for those.
- 1/4" For people looking to use 1/4" vacuum tube
-
Tired of your Dragy flying all over the car as you try to do runs? Tired of low sats or no sats warning due to improper location of the Dragy in the vehicle? Well say goodbye to those issues with our new Carbon Fiber and Plastic Dragy holders. These are made from either 100% Pre-Preg Carbon Fiber, or molded plastic for a perfect fit. The carbon fiber gives it just the right look to add to your performance vehicle! Each holder has dual Suction cups and will stick to any smooth surface. We suggest mounting them in the upper left or right corner of your windshield with a full view of the sky. Dragy holder features
- Stop your Dragy from flying off the dash, and having to search for it
- Position your Dragy in the optimal position for the best satellite coverage
- VTT Dragy holder exposes the entire top of the Dragy so nothing is blocking the receiver from the Satellite
- The charging port is not blocked and can be accessed with the cover on
- Choose from REAL Carbon Fiber or Molded Plastic
-
VTT is happy to offer our very unique and universal billet mount to fit any roll bar or cage with 1.5", 1.75", or 2" diameter tubing. These mounts are designed from 6061-T6 aluminum and are made to SECURELY hold a JBL Flip version 3 - Version 6 and allows you to bring music into your race car, off-road vehicle, rock crawler, boat, basically anything that has a length of tubing this will allow you to have an easy way to have tunes without having to install and mount a stereo system. They can also be used as a single mount to hold things such as a helmet, steering wheel, or anything you want to quickly hang for easy access once seated. For the JBL flip you will need TWO mounts, simply install them loosely, snap in your JBL Flip to get the proper spacing, and tighten down. The device is then securely mounted and can be removed easily. We offer these in a variety of anodized colors for a long-lasting durable finish including Black, Red, Blue, Clear, Orange, and Green Mounts are sold individually Features:
- Billet 6061-T6 Aluminum construction anodized in a variety of colors
- Can be used to SECURELY mount a JBL Flip 3-6 to anything that has a length of 1.5", 1.75" or 2" tubing
- Can also be used as a universal mount for anything you need to hang in your race car, off-road vehicle, etc
- Completely reversible, and can be moved from vehicle to vehicle
-
Looking for Mac solenoids for your build? We got em here at VTT-FAB so you can get everything in one place. We have 3-port, and 4-port in stock!
-
Unsure of the state of your CHRA's, whether brand new from a questionable source or rebuilt? Don't install them without having a proper High-Speed balance done! This is the #1 most critical factor when building a turbocharger, and is even more important for performance turbochargers or small twins that see a LOT of RPM. We use a Turbo Technics VS3 balancer, and balance most units down to under .5G Not all turbos will be able to pass a high-speed balancing test for any number of reasons (usually poor assembly, bent shaft, etc), if they will not pass, we will send you the specs they are in, and as close as we could get them. We then will give you the option to send them back, or we can disassemble, and rebuild them in-house using our other balancing, and assembly tools to ensure a properly built/balanced unit. The service is for most turbos, and we have the capability to balance most units, NOT ALL. If sending in twins please choose TWO as the quantity
UNITS MUST BE SENT IN WITH NO HOUSINGS, AND IN A CONDITION READY TO BE BALANCED, IF YOU NEED TO SEND IN COMPLETE TURBOS, WE CAN DISASSEMBLE, AND BALANCE FOR YOU, BUT AN EXTRA CHARGE WILL APPLY. IF THE UNITS ARE SENT IN A CONDITION WHERE THEY CAN NOT BE BALANCED WE WILL LET YOU KNOW THE PRICE TO GET THEM TO A STATE WHERE THEY CAN BE
-
VTT Billet Velocity Stack (V-Stack)
3" • 4" • 5" Inlet Sizes
Running an open turbo and want to straighten airflow into the compressor for maximum efficiency? The VTT Billet Velocity Stack is exactly what you need.
Backed by fluid-dynamics principles, a proper bellmouth / velocity stack smooths incoming airflow, reduces turbulence, and improves air entry into the turbocharger—or intake on naturally aspirated applications. Unlike thin, stamped alternatives, our V-Stacks are precision-machined for strength, consistency, and performance.
Each unit is CNC-machined from 6061-T6 billet aluminum and anodized for durability and corrosion resistance. Available in 3", 4", and 5" inlet sizes, these stacks are designed to fit any intake tubing or turbocharger inlet of the corresponding diameter.
-
VTT EVO X Billet One-Way Crankcase Breather
VTT is happy to introduce the first and only available plug-and-play ONE-WAY crankcase breather kit for the 2008-2015 EVO X applications. With this breather simply remove your oil cap, install the breather, and instantly free up horsepower, improve turbo draining, and remove crankcase pressure, all while adding a cool look to your engine bay.Can be used by itself with the stock PCV system to eliminate crankcase pressure, or with any number of PCV setups, including our VTT Engine catch cans, and billet Valve CoverMade from 6061-T6 Aircraft aluminum anodized black for a long-lasting finish, 4 stainless steel baffles for complete oil control, a PTFE one-way check ball, a high-quality filter, and a clamp all work together to keep crankcase pressure where it belongs, out of your crankcase.This is a SERVICE item, it is designed to capture and hold oil that is pulled from the spent gasses when it gets saturated, it must be cleaned
-
Secure Your AN Fittings the Right Way – Without the Damage
VTT now offers a complete line of precision Billet 6061-T6 Aluminum AN Wrenches, designed to grip without marring your fittings. Whether you're working with -3 or -20 AN sizes, we've got you covered.These wrenches are lightweight, durable, and anodized in 8 vibrant colors for a long-lasting finish and easy size identification.
Available Options:
-
Full Kit: Includes all sizes from -3 to -20
-
Common Size Kit: Includes -4, -6, -8, -10, and -12
-
Individual Wrenches: Purchase only the sizes you need
-
-
VTT -16 Billet HIGH-FLOW Catch Can System
Maximum Venting for Maximum Power
VTT is proud to introduce our -16 Billet High-Flow Catch Can System — designed from the ground up for high-horsepower applications requiring serious crankcase ventilation. Whether you're pushing over 900WHP or beyond 2000WHP, this system delivers unmatched performance, reliability, and engine bay cleanliness.
Key Features:
-
Supports -16 AN lines (with optional -12 or -20 fittings)
- 20 Fluid OZ capacity
-
Engineered for big-power builds needing high crankcase pressure relief
-
Triple-stage filtration system to eliminate oil mist — even in the event of engine failure
-
Designed, tested, and proven to keep oil inside the catch can — not in your engine bay
Triple Filtration Technology:
-
Stage 1 - Stainless steel filter – captures 95% of oil mist on entry
-
Stage 2 - Perforated diffuser plate – further disperses and slows down airflow
-
Stage 3 - Final stainless mesh layer – scrubs out any remaining vapor before venting
This advanced system has been tested with over 200 PSI of pressure and more than half a quart of oil without releasing a trace of oil mist. As long as the catch can is properly serviced and not overfilled, even catastrophic engine failure won’t result in a mess under your hood.
Application-Specific Kits Available:
We offer plug-and-play kits for popular platforms, including:
-
G8X M2/M3/M4 (S58) SINGLE TURBO ONLY
-
F9X X3M/X4M SINGLE SINGLE TURBO ONLY
-
A9X Toyota Supra
Each Plug and play kit includes everything needed for installation: catch can, vehicle-specific bracket, fittings, hoses, and optional drain. Again, plug-and-play kits include ALL required parts. Bracket, fittings, line, etc. No additional fittings are required except the drain if wanted.
-
-
VTT is proud to offer PTE Turbocharger products! Please Note: All Precision Turbos have a 2-3 week shipping time
-
Sale!
VTT x PFS EBS (External Brushless System) Fuel System
VTT, in collaboration with Performance Fueling Solutions (PFS), is proud to introduce the PFS EBS — External Brushless System.
The EBS is a fully stand-alone, next-generation brushless fuel system available in both platform-specific and universal fitments. Built around state-of-the-art Protec brushless pump technology, this system is capable of supporting up to 2,500 HP on ethanol-based fuels — and even more on gasoline or ethanol blends.
With its compact 15" x 10" footprint and ultra-lightweight construction, the PFS EBS is engineered for performance without compromise. The complete system — including pumps, surge tank, FPR, controllers, and wiring harness — weighs in at under 10 lbs (dry), thanks to a carbon fiber mounting plate and carefully chosen lightweight materials.
EBS Bench Testing Video:
EBS Bench Test Video
