-
Unsure of the state of your CHRA's, whether brand new from a questionable source or rebuilt? DON'T install them without having a proper High-Speed balance done! This is the #1 most critical factor when building a turbocharger, and is even more important for performance turbochargers or small twins that see a LOT of RPM. We use a Turbo Technics VS3 balancer, and balance most units down to under .5G Not all turbos will be able to pass a high-speed balancing test for any number of reasons (usually poor assembly, bent shaft, etc), if they will not pass, we will send you the specs they are in, and as close as we could get them. We then will give you the option to send them back, or we can disassemble, and rebuild them in-house using our other balancing, and assembly tools to ensure a properly built/balanced unit. The service is $79.99 each for most turbos, and we have the capabilities to balance most units. If sending in twins please choose TWO as the quantity
UNITS MUST BE SENT IN WITH NO HOUSINGS, AND IN A CONDITION READY TO BE BALANCED, IF YOU NEED TO SEND IN COMPLETE TURBOS, WE CAN DISASSEMBLE, AND BALANCE FOR YOU, BUT AN EXTRA CHARGE WILL APPLY. IF THE UNITS ARE SENT IN A CONDITION WHERE THEY CAN NOT BE BALANCED WE WILL LET YOU KNOW THE PRICE TO GET THEM TO A STATE WHERE THEY CAN BE
-
Sale!
VTT BMW E9/8X Double Adjust Drag Shock Kit
$1,199.99$1,109.99Looking to maximize your E9/8X Series BMW for drag racing? Want to be able to dial in the perfect amount of compression or rebound on your launch? The VTT Double adjust drag shock kit is just want the doctor ordered! -
VTT E9/8X Rear Drag Brake Conversion Kit
$839.99 – $1,009.99VTT ultimate E8/9X ultimate rear brake conversion kit VTT is happy to announce its new rear brake conversion kits for the E8X/E9X platforms. We take what already exists on the market, and make it much more complete, and much more performance-oriented while keeping the clearance for those 15” wheels. This kit replaces your rear brake rotors and calipers to fit 15″ wheels. It includes lightweight Wilwood calipers to go from the single-piston factory caliper to race-inspired 4 Piston calipers. While dropping up to a whopping 20 LBS of unsprung weight off the back of your vehicle! -
VTT Virtual Gift Card
$50.00 – $1,000.00Please Note: This is a Virtual Gift Card. After purchase you will receive an email with your Gift Card code
-
VTT BMW TITANIUM 5×112 to 5×114 Bolt Pattern Conversion Kits
$189.99 – $369.99Looking to convert your 5x112 M14x1.25 BMW vehicle to 5x114 to open up your wheel options? Want to drop 60% of the weight off steel options? We got covered with our VTT TITANIUM wheel stud conversion kits. These kits are Grade 5 Titanium studs, rated at more than 135,000PSI Tensile Strength, with Grade 5 Titanium nuts with a 60-degree cone seat to fit most all aftermarket wheel applications and convert your vehicle to M12x1.5 wheel studs which allow you to fit 5x114 wheels with no other changes.PLEASE NOTE – THESE STUDS WILL ONLY WORK IF YOUR WHEELS ARE DRILLED M14 THESE WILL NOT WORK FOR WHEELS DRILLED M12!
DO NOT USE ANY HUB-CENTERING SLEEVES WITH THESE CONVERSION STUDS, THE LUGS WILL CENTER THE WHEELS. THE USE OF A CENTERING SLEEVE MAY LEAD TO STUDS BREAKING. FOR INSTALLATION YOU MUST SNUG EACH LUB UP SLOWLY, AND IN A STAR PATTERN TO GET THE WHEEL CENTERED ON THE LUGS, FAILURE TO DO SO CAN ALSO LEAD TO FAILURE.
-
VTT is Proud to offer our Billet Aluminum DCT Transmission pan. This pan does away with the factory plastic pan and upgrades it to 6061-T6 aluminum anodized in a variety of colors. This pan increases fluid capacity by 80% or almost DOUBLE the stock pan, has a US-made reusable Viton Gasket, a rare earth magnet built in to pull metal from the fluid, machined external fins to help aid in cooling, and a -6 ORB drain plug. Product Features:
- Billet construction using 6061-T6 aluminum for long life, and added strength
- 80% or Almost DOUBLE the factory fluid capacity at 2000ML compared to 1150ML
- Machined fins for improved cooling
- Rare Erath magnet built in to pull metal from the fluid
- US-Made Viton Gasket
- -6 ORB drain plug for easy service
-
Need a Tee fitting for plumbing Vacuum, or Boost lines, Don't want to use cheap plastic ones that can get soft when hard, and brittle after they heat cycle? We didn't either, which is why we machined these high-quality billet tees to solve this issue. Machine from 6061-T6 aluminum, and anodized in black for a long-lasting corrosion-free finish, these tees look great, and will you never have to worry about one failing. We offer them in two sizes, each size has 12mm legs and 3 barbs:
- 7.60mm / -4 Push Lock for people looking to use -4 push lock hose or -4 AN hose. This is a perfect fit for those.
- 1/4" For people looking to use 1/4" vacuum tube
-
Adding a Front-facing manifold to your N54, and need to extend your map sensor harness? We got you covered with our 24" extension harness. High-quality wiring, with seating, and our own 3D printed connectors ensure a perfect fit. Fits all N54, and very early N55, please check your plug connection on your map sensor before ordering
-
VTT E90 Carbon Fiber Headlight Duct
$579.99 – $629.99VTT Carbon Fiber headlight duct for the E90 will complete any racecar or streetcar build helping to get rid of weight and add functionality with a working 6″ velocity stack to run your turbocharger into for optimal flow, and ram air. 100% multi-layer prepreg Carbon Fiber, with a UV resistant clear coat for the ultimate in strength, and durability! We offer them in the following varieties: Passenger side duct with 6″ Velocity stack 3″ hose connection Passenger side duct with 6″ Velocity stack 4″ hose connectionFITMENT: PLEASE NOTE IT FITS ALL E90, AND E91 MODELS INCLUDING M3, ETC. THIS LIGHT HAS NOT BEEN TEST FIT ON AN LCI VEHICLE, AND WE CAN NOT CONFIRM IT FITS LCI. WE CAN ONLY CONFIRM PRE-LCI FITMENT AT THIS TIME.
-
VTT-FAB Billet Velocity Stack
$39.99 – $49.99Running an open turbo, and want to straight out the airflow to the compressor for extra efficiency. Our billet velocity stack is what you need. Backed by physics a Bellmouth or velocity stack will help smooth the air coming into the turbocharger or on NA cars. These are made from 6061-T6, and anodized in a variety of colors and sizes. Currently, we offer 3", 4", and 5" These are suitable to fit any intake tubing or turbocharger inlet with that size. These are available with or without a silicone connector and clamps. Our V-Stacks are also made to extend down on the outside so you can attach a Vibrant S&B or other compatible 7" Filter on the 3"/4" version. Features:- Smooth air before it enters the turbocharger or Intake
- Very low profile, only sticking 2.5" above the turbocharger inlet. Even if you have no room for a filter these will fit
- Fits all turbochargers with a 3", 4" or 5" inlet including PTE Sportsman Cover!
- 3" and 4" version works with Vibrant #10961 7" filter or S&B 1032 Filter if you have room
- 100% billet construction for high-strength
- Anodized for long life, and durability
-
VTT “DCS” EWG System for TurboSmart Straight Gates
$799.99 – $1,499.99VTT is proud to offer our EWG "Direct Control System" or DCS! This is a completely new innovation for people looking to control the highest-flowing wastegate on the market using an existing BMW electronic actuator. This system will allow BMW owners who have a vehicle with Electronic Wastegates from the factory to utilize this system to control an externally wastegated turbo system, AND it will ALSO allow ANY vehicle to use this setup to control your own custom turbo system. This is done by utilizing our custom 7075 Billet aluminum bracket coupled with a Turbosmart Straight gate, and if needed an EWG controller made for us by DCCD Pro. This allows direct external wastegate control over any turbocharger system with or without EWG for the factory. Features:- Utilizes the most current wastegate technology the Turbosmart Straight Gate. This gate allows maximum flow with minimal restriction, low drive pressure, and much more. Full details can be found here - https://www.turbosmart.com/product/electronic-straightgate-esg50-external-wastegate/
- Can be configured in multiple ways, and angles based on how you mount the adapter
- The adapter is 7075 Aluminum which has the strength of steel and weight of aluminum
- All connection fittings, are made from Nitronic 60 which has extremely high temperature and wear properties
- Zero Drive Pressure, no springs, no poppet valves, direct control over the gate using factory ECU logic
- Adaptable to ANY turbo system on any car to provide the ultimate in boost control!
-
Looking to adapt your wheel bore size to a smaller hub bore? VTT has you covered with our hub-centric adapters. These adapters are made from Billet 6061-T6 aluminum, and anodized in black. We have these sizes currently
- 57.1mm hub to 60.1mm wheel bore
- 57.1mm hub to 64.1mm wheel bore
- 57.1mm hub to 66.1mm wheel bore
- 57.1mm hub to 66.6mm wheel bore
- 57.1mm hub to 67.1mm wheel bore
- 57.1mm hub to 70.3mm wheel bore
- 57.1mm hub to 71.6mm wheel bore
- 57.1mm hub to 72.6mm wheel bore
- 57.1mm hub to 73mm wheel bore
- 57.1mm hub to 74mm wheel bore
- 57.1mm hub to 74.1mm wheel bore
- 64.1mm hub to 72.6mm wheel bore
- 66.6mm hub to 72.6mm wheel bore
They are sold in sets of two, order TWO SETS for a full car, or one set per axle.
-
VTT-FAB Carbon Fiber Turbo Blanket
$64.99 – $99.00Looking to keep the underhood heat down on your single turbo car, or build? We got you covered with our VTT-FAB Carbon Fiber Turbo Blankets. The outer shell is made of Carbon Fiber, and the inner shell is Silica Fiber. For 2500F intermittent / 1800 direct heat rating. We have them in 2 sizes T3, and T4. See fitment below Kit included:- 1 Carbon Blanket of choice
- 2 install springs
-
Sale!
VTT BMW Wireless Plug, and Play Line Lock Kit
$649.00$599.00VTT is proud to offer a truly plug-and-play line lock kit for select BMW vehicles that does NOT require running wiring inside the car, mounted switches, holes in the dash, etc. Our newly designed and released line lock kits use a 40amp wireless remote control switch with 4 different modes that allow you to tailor your line lock setup exactly as you prefer. You simply install the solenoids, install the harness with the switch which has all the wiring terminated, bleed the brakes, and you are ready for effortless burnouts which will not be interfered with by the DME because you are holding the brakes, nor wear your rear brake pads. You can store the remote anywhere in your vehicle, center console, cup holder, door cup holder, etc., and when you need to do a burnout to heat your race tires it's in arm's reach without running any wiring into the vehicle. Fitment is confirmed for G8X M3/4, A9X Supra - The kit itself including lines, solenoids, etc will fit most all late model BMW Chassis including F8X, F3X, G2X, etc. The main concern will be mounting the wireless switch in the passenger cowl area. The kit includes:- Line lock solenoids with weather pack connectors
- Two Parker 90-degree -3 an fittings
- Two Stainless Steel adapter fittings
- Two DOT Approved Stainless Steel brake lines
- One complete wiring harness
- One Remote control switch with TWO remotes
-
PTE – Precision Turbochargers
$2,234.49 – $4,428.99VTT is proud to offer PTE Turbocharger products! -
Looking to remove your BOV either for leak testing, or dont want to run one, and your charge pipe or housing has a flange on it. You can use this billet plate to block off the BOV flange. Uses the O-ring from the BOV to seal, and removes the BOV. Fitment: Tial BOV Turbosmart BOV with female flange like Tial
-
VTT is happy to offer custom tig welded 304 Stainless N54/N55 equal-length turbo manifolds. These are perfect for someone trying to fabricate a twin-turbo setup, and needs manifolds. The flange will fit any Garret turbo from GT series, GTX series, and G-Series G25, and G30 V-band.
These are sold as a set of TWO
-
Looking to protect your single turbo investment, dont have a ton of room, and need a low profile filter that can flow what you need? VTT Has you covered with our Low Profile Single turbo Air Filters. These filters are custom-made for VTT. They are made with a heat-resistant silicone base, and a high-flowing cotton weave element with a pre-oiled design to catch contaminates but allow free flow. We currently offer them in Black, and 3 flange sizes. 3", 4" and 5" flange. With two filter heights. Tested at over 1200WHP with no loss of power observed. Filter Options - Offered in White, and Black with the following dimensions Short - 3.75" Tall, 7.5" OD Large end, 5" Small end 3", 4", or 5" Flange Tall - 4.5" Tall, 7.5" OD Large end, 5" Small end 3", 4", or 5" Flange
-
Sale!
BMW Factory OEM EWG Actuator Replacement – 11 65 8 691 853
$499.00$349.00Looking to replace your damaged factory BMW Actuator part number - 11658691853 VTT has located and ordered in bulk these actuators, and offer them at a discounted price. These are 100% FACTORY BMW OEM actuators, not aftermarket. Fitment is for the following, but they work to replace basically any BMW Actuator. -
VTT Crank Hub Install Special!
$2,000.00VTT is happy to announce our Spline lock Crnak Hub special! We are offering COMPLETE crank hub service for N54, N55, And S55 using our Spline Lock hubs for $2000 out the door, this includes all parts, and labor required. The usual turnaround time is 2 days, but we can get them done in one day if early morning drop-off is done. Our shop is in Hayward, CA 94541, and we are currently taking appointments to fill up our calendar through the holidays!If you are interested, please email [email protected] with the words "Crank Hub Appointment" in the title, and we can get back to you with an open time slot ASAP. Thank you!
AGAIN: Once purchased you MUST email [email protected] to schedule an appointment. You CANNOT show up until you have appointment CONFIRMATION.
-
VTT Physical Gift Cards
$50.00 – $1,000.00Give the Gift of VTT! Looking to get your friends, or family some go-fast parts, and no idea what they need, only that they love VTT? Well, our Gift Cards have you covered! They come in $50, $100, $250, $500, and $1000 increments. Each gift card is precision cut out of plastic in the shape of the VTT logo and has the dollar amount and the code on the back. Each gift code is unique and is locked to that card. To redeem simply enter the code during check out it will remove that amount, and if you have any leftover it will go back to the card.
You can choose to have your card physically mailed to you, or a virtual card where we can send you a scan of your card.
