-
Looking to remove your BOV either for leak testing, or dont want to run one, and your charge pipe or housing has a flange on it. You can use this billet plate to block off the BOV flange. Uses the O-ring from the BOV to seal, and removes the BOV. Fitment: Tial BOV Turbosmart BOV with female flange like Tial
-
VTT “DCS” EWG System for TurboSmart Straight Gates
$799.99 – $1,499.99VTT is proud to offer our EWG "Direct Control System" or DCS! This is a completely new innovation for people looking to control the highest-flowing wastegate on the market using an existing BMW electronic actuator. This system will allow BMW owners who have a vehicle with Electronic Wastegates from the factory to utilize this system to control an externally wastegated turbo system, AND it will ALSO allow ANY vehicle to use this setup to control your own custom turbo system. This is done by utilizing our custom 7075 Billet aluminum bracket coupled with a Turbosmart Straight gate, and if needed an EWG controller made for us by DCCD Pro. This allows direct external wastegate control over any turbocharger system with or without EWG for the factory. Features:- Utilizes the most current wastegate technology the Turbosmart Straight Gate. This gate allows maximum flow with minimal restriction, low drive pressure, and much more. Full details can be found here - https://www.turbosmart.com/product/electronic-straightgate-esg50-external-wastegate/
- Can be configured in multiple ways, and angles based on how you mount the adapter
- The adapter is 7075 Aluminum which has the strength of steel and weight of aluminum
- All connection fittings, are made from Nitronic 60 which has extremely high temperature and wear properties
- Zero Drive Pressure, no springs, no poppet valves, direct control over the gate using factory ECU logic
- Adaptable to ANY turbo system on any car to provide the ultimate in boost control!
-
Looking to protect your single turbo investment, dont have a ton of room, and need a low profile filter that can flow what you need? VTT Has you covered with our Low Profile Single turbo Air Filters. These filters are custom-made for VTT. They are made with a heat-resistant silicone base, and a high-flowing cotton weave element with a pre-oiled design to catch contaminates but allow free flow. We currently offer them in Black, and 3 flange sizes. 3", 4" and 5" flange. With two filter heights. Tested at over 1200WHP with no loss of power observed. Filter Options - Offered in White, and Black with the following dimensions Short - 3.75" Tall, 7.5" OD Large end, 5" Small end 3", 4", or 5" Flange Tall - 4.5" Tall, 7.5" OD Large end, 5" Small end 3", 4", or 5" Flange
-
VTT is proud to offer our "OBD-LOCK" OBD port locking tool. This tool is made from billet 6061-T6 aluminum and is designed to completely lock out your OBD port from being accessed. This is useful for people who do not want dealers, techs, etc from accessing their OBD port, and possibly changing a tune, etc. This is also perfect for anti-theft prevention as it will not allow a would-be thief to hook up to the car's OBD port, duplicate a key, etc. The OBD-LOCK cannot be removed without physically destroying the OBD port if you do not have the proper tools. VTT uses 5 types of screw head designs for every 200 OBD-LOCKS made. This means that worldwide only 40 OBD-LOCKS are using the same head design. For each batch of 200, we redesign the screw heads meaning every batch of 200 OBD-LOCKS will use different screw heads and tools. Each OBD-LOCK sent has its head design chosen at random. After Extensive testing, we have found that our OBD lock fits EVERY SINGLE OBD port we have tried, this means it will fit every single OBD port currently on the market from a high-end BMW to a Ford F150 diesel. If you order one, and find it does not fit, PLEASE let us know.
FITMENT: We have TWO versions one for ALL GM vehicles and one for ALL NON-GM Vehicles. Please order the one you
-
Sale!
BMW Factory OEM EWG Actuator Replacement – 11 65 8 691 853
$499.00$349.00Looking to replace your damaged factory BMW Actuator part number - 11658691853 VTT has located and ordered in bulk these actuators, and offer them at a discounted price. These are 100% FACTORY BMW OEM actuators, not aftermarket. Fitment is for the following, but they work to replace basically any BMW Actuator. -
VTT-FAB Billet Oil/Coolant Fittings, and block offs
$20.00 – $40.00Looking to fab your own turbo kit for BMW platforms, and need an easy solution to block off water lines, or create feed and drain fittings. Look no further, we offer a wide range of oil/coolant fitting options for most late-model BMW platforms. See the Full description below for a full part number breakdown -
Soft bushings are the enemy of launching hard, and keeping your drivetrain together. The BMW Transfer Case bushings are notoriously soft, and that is the opposite of what you want when launching a car hard. You can replace the bushing with a solid one, but this is time-consuming usually requires lowering or removing the transfer case, and results in a lot of added NVH. The best path is simply to reduce the amount of flex of the factory bushing so you keep the nice manners when cruising around town, and at idle, but when its time to the launch the transfer case cannot move as it could without the insert. These come as a set of two with 2 bolts to keep them in place. Install time once you get to them is about 2-3 minutes. Could not be easier. Put some lube on them, push them in, and tighten the screws. These are a MUST for high-power G8X, and F9X X3/X4M Builds. All platforms they fit are below. Features:
- 6061- T6 aluminum construction
- Easy to install
- Fully reversible
- Do not add NVH
-
Sale!
VTT Billet Large Capacity BMW ZF8HP Transmission Pan
$699.00$599.00VTT is Proud to offer our Billet Aluminum ZF8HP 8-speed Transmission pan. This pan does away with the factory plastic or cast aluminum pan and upgrades it to 6061-T6 aluminum anodized in a variety of colors. This pan increases fluid capacity to 5.7 QTs compared to the stock pan which holds 3.7 QTs, has a US-made reusable Viton Gasket, a rare earth magnet that sits under the filter to not only support it, but pulls metal from the fluid, machined external fins to help aid in cooling, and a -6 ORB magnetic drain plug. Clearance is NOT increased on G8X, X3/4M, or F90 M5, if used on smaller model ZF8HP with the plastic pan, the pan DOES fit but has reduced clearance. Product Features:- Billet construction using 6061-T6 aluminum for long life, and added strength
- Add a full 2 QTs fluid capacity at 5450ML (5.7QTs) compared to 3500ML (3.7QTs)
- Machined fins for improved cooling
- Rare Erath magnet built in to pull metal from the fluid
- US-Made Viton Gasket
- -6 ORB magnetic drain plug for easy service
-
Sale!
VTT-FAB M7 Copper Locking Exhaust Nuts
$3.00$1.49Are you building a single kit for the N54, N55, or S55 platform? M7 Locking exhaust nuts is not easy. So we made our own to combat the issue. These are the perfect solution to the problem of hard-to-find M7 lock nuts. Sold individually so order the number you need.Note: This is nuts ONLY Stud not included, by our extended M7 studs here - https://vargasturbo.com/product/vtt-fab-extended-m7-n54-n55-s55-b58-2-port-head-studs/
-
Sale!Are you building a single kit for the N54, N55, or S55 platform? The stock studs are usually a little bit short for most single-head flanges, and finding M7 studs is not easy. So we made our own longer studs to combat the issue. Made from 10.9 grade steel, and coated in black oxide, these are the perfect solution to the short stud problem. Sold individually so order the number you need. Stud details are as follows
- Overall length 47mm (stock 39mm)
- 3mm shoulder
- 6mm head which is 5mm hex
- 14mm short end
- 24mm long end (stock 15mm)
Dont forget our M7 copper lock nuts as well to complete the job - https://vargasturbo.com/product/vtt-fab-m7-copper-locking-exhaust-nuts/
-
VTT-FAB Billet Velocity Stack
$39.99 – $49.99Running an open turbo, and want to straight out the airflow to the compressor for extra efficiency. Our billet velocity stack is what you need. Backed by physics a Bellmouth or velocity stack will help smooth the air coming into the turbocharger or on NA cars. These are made from 6061-T6, and anodized in a variety of colors and sizes. Currently, we offer 3", 4", and 5" These are suitable to fit any intake tubing or turbocharger inlet with that size. These are available with or without a silicone connector and clamps. Our V-Stacks are also made to extend down on the outside so you can attach a Vibrant S&B or other compatible 7" Filter on the 3"/4" version. Features:- Smooth air before it enters the turbocharger or Intake
- Very low profile, only sticking 2.5" above the turbocharger inlet. Even if you have no room for a filter these will fit
- Fits all turbochargers with a 3", 4" or 5" inlet including PTE Sportsman Cover!
- 3" and 4" version works with Vibrant #10961 7" filter or S&B 1032 Filter if you have room
- 100% billet construction for high-strength
- Anodized for long life, and durability
-
VTT BMW TITANIUM 5×112 to 5×114 Bolt Pattern Conversion Kits
$189.99 – $369.99Looking to convert your 5x112 M14x1.25 BMW vehicle to 5x114 to open up your wheel options? Want to drop 60% of the weight off steel options? We got covered with our VTT TITANIUM wheel stud conversion kits. These kits are Grade 5 Titanium studs, rated at more than 135,000PSI Tensile Strength, with Grade 5 Titanium nuts with a 60-degree cone seat to fit most all aftermarket wheel applications and convert your vehicle to M12x1.5 wheel studs which allow you to fit 5x114 wheels with no other changes.PLEASE NOTE – THESE STUDS WILL ONLY WORK IF YOUR WHEELS ARE DRILLED M14 THESE WILL NOT WORK FOR WHEELS DRILLED M12!
DO NOT USE ANY HUB-CENTERING SLEEVES WITH THESE CONVERSION STUDS, THE LUGS WILL CENTER THE WHEELS. THE USE OF A CENTERING SLEEVE MAY LEAD TO STUDS BREAKING. FOR INSTALLATION YOU MUST SNUG EACH LUB UP SLOWLY, AND IN A STAR PATTERN TO GET THE WHEEL CENTERED ON THE LUGS, FAILURE TO DO SO CAN ALSO LEAD TO FAILURE.
-
Looking to go above 45 psi in your BMW-powered vehicle? Looking for a plug-and-play solution? We have you covered with our BMW 5 bar sensor. These will allow 58 psi to be read and are factory plug, and play. Simply remove your old sensor, replace it with the 5 bar, and have your tuner rescale your map values in both your DME tune and your PI tune if applicable. These are GENUINE BMW sensors directly from BMW.
-
VTT is happy to offer our very unique and universal billet mount to fit any roll bar or cage with 1.5", 1.75", or 2" diameter tubing. These mounts are designed from 6061-T6 aluminum and are made to SECURELY hold a JBL Flip version 3 - Version 6 and allows you to bring music into your race car, off-road vehicle, rock crawler, boat, basically anything that has a length of tubing this will allow you to have an easy way to have tunes without having to install and mount a stereo system. They can also be used as a single mount to hold things such as a helmet, steering wheel, or anything you want to quickly hang for easy access once seated. For the JBL flip you will need TWO mounts, simply install them loosely, snap in your JBL Flip to get the proper spacing, and tighten down. The device is then securely mounted and can be removed easily. We offer these in a variety of anodized colors for a long-lasting durable finish including Black, Red, Blue, Clear, Orange, and Green Mounts are sold individually Features:
- Billet 6061-T6 Aluminum construction anodized in a variety of colors
- Can be used to SECURELY mount a JBL Flip 3-6 to anything that has a length of 1.5", 1.75" or 2" tubing
- Can also be used as a universal mount for anything you need to hang in your race car, off-road vehicle, etc
- Completely reversible, and can be moved from vehicle to vehicle
