-
Sale!
BMW Factory OEM EWG Actuator Replacement – 11 65 8 691 853
$499.00$349.00Looking to replace your damaged factory BMW Actuator part number - 11658691853 VTT has located and ordered in bulk these actuators, and offer them at a discounted price. These are 100% FACTORY BMW OEM actuators, not aftermarket. Fitment is for the following, but they work to replace basically any BMW Actuator. -
Sale!
BMW/Toyota 5×112 to 5×114 Bolt Pattern Conversion Kits
$69.99 – $129.99Looking to convert your 5x112 M14x1.25 vehicle such as A90/91 Toyota Supra, and 2020+ BMW G-series to 5x114 to open up your wheel options? We got covered with our VTT wheel stud conversion kits. These kits are forged cold-rolled steel in 10.9 class, with corrosion-resistant coating for years of use, and convert your vehicle to M12x1.50 wheel studs which allow you to fit 5x114 wheels with no other changes.PLEASE NOTE – THESE STUDS WILL ONLY WORK IF YOUR WHEELS ARE DRILLED M14 THESE WILL NOT WORK FOR WHEELS DRILLED M12!
DO NOT USE ANY HUB-CENTERING SLEEVES WITH THESE CONVERSION STUDS, THE LUGS WILL CENTER THE WHEELS. THE USE OF A CENTERING SLEEVE MAY LEAD TO STUDS BREAKING. FOR INSTALLATION YOU MUST SNUG EACH LUG UP SLOWLY, AND IN A STAR PATTERN TO GET THE WHEEL CENTERED ON THE LUGS, FAILURE TO DO SO CAN ALSO LEAD TO FAILURE.
-
Sale!
BMW/Toyota M14x1.25 to M14x1.50 Wheel Stud conversion Kits
$69.99 – $129.99Looking to convert your Supra or G Series BMW to wheel studs. Want to get rid of the difficult to find M14x1.25 ultra-fine thread and convert it to M14x1.15? We got covered with our VTT wheel stud conversion kits. These kits are forged cold rolled steel in 10.9 class, with corrosion-resistant coating for years of use, and convert your M14x1.25 vehicle to M14x1.50 wheel studs. -
Unsure of the state of your CHRA's, whether brand new from a questionable source or rebuilt? DON'T install them without having a proper High-Speed balance done! This is the #1 most critical factor when building a turbocharger, and is even more important for performance turbochargers or small twins that see a LOT of RPM. We use a Turbo Technics VS3 balancer, and balance most units down to under .5G Not all turbos will be able to pass a high-speed balancing test for any number of reasons (usually poor assembly, bent shaft, etc), if they will not pass, we will send you the specs they are in, and as close as we could get them. We then will give you the option to send them back, or we can disassemble, and rebuild them in-house using our other balancing, and assembly tools to ensure a properly built/balanced unit. The service is $79.99 each for most turbos, and we have the capabilities to balance most units. If sending in twins please choose TWO as the quantity
UNITS MUST BE SENT IN WITH NO HOUSINGS, AND IN A CONDITION READY TO BE BALANCED, IF YOU NEED TO SEND IN COMPLETE TURBOS, WE CAN DISASSEMBLE, AND BALANCE FOR YOU, BUT AN EXTRA CHARGE WILL APPLY. IF THE UNITS ARE SENT IN A CONDITION WHERE THEY CAN NOT BE BALANCED WE WILL LET YOU KNOW THE PRICE TO GET THEM TO A STATE WHERE THEY CAN BE
-
NGK 94201 Spark plug set for all S58/B58/48 applications, and ALSO for N54/55 running the new B58 coil upgrade. We recommend these for running 100% e85, and high boost on many BMW applications including N54, N55, S55, if you upgrade to the B58 coils. These are also great maintenance replacements for your S58/B58/48 powered vehicle at a much better price than most. Plugs can be bought as a set of 6. You can add pre-gapping for an additional $25
-
NGK 97506 Pre-Gapped Spark Plug Set
$104.99 – $139.99NGK 95706 Spark plug set required for running 100% e85, and high boost on many BMW application including N54, N55, S55, etc. Plugs can be bought as a set of 6. You can add pre-gapping for an additional $25 -
One Ethanol Racing Fuel
$69.99 – $559.99Please note: Due to heavy increases in freight costs we have had to raise prices by $50 on 54-gallon drums, and $15 on pails.
VTT is proud to be the West Coast dealer for One Ethanol racing fuel.
We have two blends available in 5-gallon pails and 54-gallon drums. See below for descriptions of both fuels
Fuel is available for local pick up only unless you email, and make arrangements for freight shipping. Be aware fuel is considered hazmat and the freight charges are equal to or more than the fuel in all instances. Fuel CANNOT be shipped normal shipping methods such as UPS, FED EX, etc
-
PFS is proud to offer a true drop-in LPFP for S55-powered BMWs. This LPFP needs NO additional pumps, wiring harnesses, controllers, etc. Capability is 850whp on E85 and up to 1000whp on race fuel. We start with a factory bucket, we modify it to accept our high-flow brushless fuel pump. We then re-terminate the factory wiring to accept the new pump. No wiring splices, done the same way the factory does -the right way. Every pump is fully tested on our flow bench to ensure proper function before shipping -you're going to be installing a product that has already proven itself. This pump is a true drop-in meaning you pull the factory unit out, install this pump, plug the factory plug into the hat, and you are done. The stock ECU controls the pump fully, and NO tune changes are required to take advantage of it. Installation is easy for the DIY'er, and if you use a performance shop it'll be easy for them -just tell them to remove the old and replace it with new same as factory pump.
-
PTE – Precision Turbochargers
$2,234.49 – $4,428.99VTT is proud to offer PTE Turbocharger products! -
Replacement Gasket for VTT Valve Covers
$29.99 – $64.99Need to replace the gasket on your VTT Aluminum VC? Simply choose your model from the dropdowns to ensure you get the correct version. -
S55 “GC” Turbocharger Upgrade Kit
From: $3,859.99WHP Level supported (with proper fuel, upgrades, and tuning) Stock-800WHP VTT S55 GC Turbochargers. GC stands for "Game Changers" and that is exactly what these do! They bring a fully new casting Stainless Steel turbine manifold/housing, all new compressor housing with single piece high flow inlet, as well as our tried, and true V2 GC CHRA with a Mar-M246 GTX28 profile turbine wheel, and custom compressor wheel. These turbos have NO core charges, keep your stock turbos, sell them, hold them if you want to go back to stock, etc. The turbos will come with custom VTT silicone inlet hoses to mate up with all inlets on the market making them 100% plug, and play. There is no better, more powerful, or well thought out upgrade on the market at any price point! -
S55 M3/M4 Silicone Charge Pipes Bundle
From: $389.99VTT silicone Charge Pipes are the premiere choice for your EBM Charge Pipe needs. Made from high quality, wire impregnated silicone, these inlets are a full 6mm thick, and can withstand even the harshest underhood conditions. -
S55 Turbocharger Install Kit
$309.99Everything needed to a successful install without having to make a trip to the dealer.
