-
VTT Physical Gift Cards
$50.00 – $1,000.00Give the Gift of VTT! Looking to get your friends, or family some go-fast parts, and no idea what they need, only that they love VTT? Well, our Gift Cards have you covered! They come in $50, $100, $250, $500, and $1000 increments. Each gift card is precision cut out of plastic in the shape of the VTT logo and has the dollar amount and the code on the back. Each gift code is unique and is locked to that card. To redeem simply enter the code during check out it will remove that amount, and if you have any leftover it will go back to the card.
You can choose to have your card physically mailed to you, or a virtual card where we can send you a scan of your card.
-
VTT Crank Hub Install Special!
$2,000.00VTT is happy to announce our Spline lock Crnak Hub special! We are offering COMPLETE crank hub service for N54, N55, And S55 using our Spline Lock hubs for $2000 out the door, this includes all parts, and labor required. The usual turnaround time is 2 days, but we can get them done in one day if early morning drop-off is done. Our shop is in Hayward, CA 94541, and we are currently taking appointments to fill up our calendar through the holidays!If you are interested, please email [email protected] with the words "Crank Hub Appointment" in the title, and we can get back to you with an open time slot ASAP. Thank you!
AGAIN: Once purchased you MUST email [email protected] to schedule an appointment. You CANNOT show up until you have appointment CONFIRMATION.
-
Sale!
BMW Factory OEM EWG Actuator Replacement – 11 65 8 691 853
$499.00$349.00Looking to replace your damaged factory BMW Actuator part number - 11658691853 VTT has located and ordered in bulk these actuators, and offer them at a discounted price. These are 100% FACTORY BMW OEM actuators, not aftermarket. Fitment is for the following, but they work to replace basically any BMW Actuator. -
Looking to protect your single turbo investment, dont have a ton of room, and need a low profile filter that can flow what you need? VTT Has you covered with our Low Profile Single turbo Air Filters. These filters are custom-made for VTT. They are made with a heat-resistant silicone base, and a high-flowing cotton weave element with a pre-oiled design to catch contaminates but allow free flow. We currently offer them in Black, and 3 flange sizes. 3", 4" and 5" flange. With two filter heights. Tested at over 1200WHP with no loss of power observed. Filter Options - Offered in White, and Black with the following dimensions Short - 3.75" Tall, 7.5" OD Large end, 5" Small end 3", 4", or 5" Flange Tall - 4.5" Tall, 7.5" OD Large end, 5" Small end 3", 4", or 5" Flange
-
VTT is happy to offer custom tig welded 304 Stainless N54/N55 equal-length turbo manifolds. These are perfect for someone trying to fabricate a twin-turbo setup, and needs manifolds. The flange will fit any Garret turbo from GT series, GTX series, and G-Series G25, and G30 V-band.
These are sold as a set of TWO
-
VTT-FAB Carbon Fiber Turbo Blanket
$64.99 – $99.00Looking to keep the underhood heat down on your single turbo car, or build? We got you covered with our VTT-FAB Carbon Fiber Turbo Blankets. The outer shell is made of Carbon Fiber, and the inner shell is Silica Fiber. For 2500F intermittent / 1800 direct heat rating. We have them in 2 sizes T3, and T4. See fitment below Kit included:- 1 Carbon Blanket of choice
- 2 install springs
-
VTT “DCS” EWG System for TurboSmart Straight Gates
$799.99 – $1,499.99VTT is proud to offer our EWG "Direct Control System" or DCS! This is a completely new innovation for people looking to control the highest-flowing wastegate on the market using an existing BMW electronic actuator. This system will allow BMW owners who have a vehicle with Electronic Wastegates from the factory to utilize this system to control an externally wastegated turbo system, AND it will ALSO allow ANY vehicle to use this setup to control your own custom turbo system. This is done by utilizing our custom 7075 Billet aluminum bracket coupled with a Turbosmart Straight gate, and if needed an EWG controller made for us by DCCD Pro. This allows direct external wastegate control over any turbocharger system with or without EWG for the factory. Features:- Utilizes the most current wastegate technology the Turbosmart Straight Gate. This gate allows maximum flow with minimal restriction, low drive pressure, and much more. Full details can be found here - https://www.turbosmart.com/product/electronic-straightgate-esg50-external-wastegate/
- Can be configured in multiple ways, and angles based on how you mount the adapter
- The adapter is 7075 Aluminum which has the strength of steel and weight of aluminum
- All connection fittings, are made from Nitronic 60 which has extremely high temperature and wear properties
- Zero Drive Pressure, no springs, no poppet valves, direct control over the gate using factory ECU logic
- Adaptable to ANY turbo system on any car to provide the ultimate in boost control!
-
Looking to remove your BOV either for leak testing, or dont want to run one, and your charge pipe or housing has a flange on it. You can use this billet plate to block off the BOV flange. Uses the O-ring from the BOV to seal, and removes the BOV. Fitment: Tial BOV Turbosmart BOV with female flange like Tial
-
VTT E90 Carbon Fiber Headlight Duct
$579.99 – $629.99VTT Carbon Fiber headlight duct for the E90 will complete any racecar or streetcar build helping to get rid of weight and add functionality with a working 6″ velocity stack to run your turbocharger into for optimal flow, and ram air. 100% multi-layer prepreg Carbon Fiber, with a UV resistant clear coat for the ultimate in strength, and durability! We offer them in the following varieties: Passenger side duct with 6″ Velocity stack 3″ hose connection Passenger side duct with 6″ Velocity stack 4″ hose connectionFITMENT: PLEASE NOTE IT FITS ALL E90, AND E91 MODELS INCLUDING M3, ETC. THIS LIGHT HAS NOT BEEN TEST FIT ON AN LCI VEHICLE, AND WE CAN NOT CONFIRM IT FITS LCI. WE CAN ONLY CONFIRM PRE-LCI FITMENT AT THIS TIME.
-
Adding a Front-facing manifold to your N54, and need to extend your map sensor harness? We got you covered with our 24" extension harness. High-quality wiring, with seating, and our own 3D printed connectors ensure a perfect fit. Fits all N54, and very early N55, please check your plug connection on your map sensor before ordering
-
Need a Tee fitting for plumbing Vacuum, or Boost lines, Don't want to use cheap plastic ones that can get soft when hard, and brittle after they heat cycle? We didn't either, which is why we machined these high-quality billet tees to solve this issue. Machine from 6061-T6 aluminum, and anodized in black for a long-lasting corrosion-free finish, these tees look great, and will you never have to worry about one failing. We offer them in two sizes, each size has 12mm legs and 3 barbs:
- 7.60mm / -4 Push Lock for people looking to use -4 push lock hose or -4 AN hose. This is a perfect fit for those.
- 1/4" For people looking to use 1/4" vacuum tube
-
VTT is Proud to offer our Billet Aluminum DCT Transmission pan. This pan does away with the factory plastic pan and upgrades it to 6061-T6 aluminum anodized in a variety of colors. This pan increases fluid capacity by 80% or almost DOUBLE the stock pan, has a US-made reusable Viton Gasket, a rare earth magnet built in to pull metal from the fluid, machined external fins to help aid in cooling, and a -6 ORB drain plug. Product Features:
- Billet construction using 6061-T6 aluminum for long life, and added strength
- 80% or Almost DOUBLE the factory fluid capacity at 2000ML compared to 1150ML
- Machined fins for improved cooling
- Rare Erath magnet built in to pull metal from the fluid
- US-Made Viton Gasket
- -6 ORB drain plug for easy service
-
VTT Virtual Gift Card
$50.00 – $1,000.00Please Note: This is a Virtual Gift Card. After purchase you will receive an email with your Gift Card code
-
Do you work on a lot of BMW engines from various platforms? Do you ever struggle with heavy cylinder heads, either lifting off the engine or simply moving around? Ever ruined an EXPENSIVE multi-layer head gasket while trying to install a cylinder head due to no secure way to hold it without two people? We answered yes to all of those things, and came up with a tool for anyone that works on BMWs often, and needs a way to simply, and easily remove/install, or simply move around a cylinder head. These cylinder head tools are machined from a solid billet of 6061-T6 aluminum and anodized in 4 colors for long-lasting corrosion resistance. They are knurled for a non-slip grip when oily or wet, and positioned so the head is balanced when lifting The Head Handler fits the following engines, N54, N55, S55, B58, S58 and we offer short extensions for installation with no cams/Cam ledges on the head, or long extensions for people that want to install or remove a head with cams still installed. (B58 only requires short extensions)
-
VTT-FAB Billet Mac Solenoid brackets
$45.99 – $49.99Building a kit using Mac solenoids to control boost? Need an easy way to mount it? VTT-FAB has you covered with our billet Mac Solenoid brackets. Machined from 6061 billet and anodized in 3 colors, these are the perfect way to mount your Mac valve and look good while doing it. Each kit includes:- One Mac Solenoid bracket (3-Port or 4-Port)
- 2 Allen screws to hold the valve to the bracket
- M6 Mounting Bolt
