-
Sale!
VTT S55 / N55 Crank Bolt Capture
$129.00$119.99The VTT S55 crank bolt capture. slips over the head of the crank bolt fully encapsulating it, and locks it to the crank hub, meaning it cannot back out no matter what. -
VTT BILLET BMW N54/N55/S55 Crank Seal Guard
$79.99 – $169.99VTT BILLET BMW N54/55 Crank Seal Guard.
It is a well-known issue on the BMW N54/N55/S55 platforms that your serpentine belt can fail for various reasons, when this happens you have a high chance of the belt getting sucked behind the front damper, and then being pushed past the crank seal into your oil pan. From there it can get sucked into the oil pick up causing total engine failure, even if you do not lose the engine it is a COSTLY repair to remove the sub-frame and drop the oil pan to remove the belt. The best way to combat this is to watch for oil leaks and keep up on your maintenance. BUT Even with those preventative measures, pre-mature belt failure can occur. This crank seal guard installs over your front crank seal and will keep the belt from being sucked in if a belt failure does occur. This is a cheap way to ensure you do not end up having to replace your motor from oil starvation due to an ingested belt. -
Sale!
VTT Billet Check Valves
$24.99 – $29.99VTT CNC Billet check valve that can be used for a variety of uses including a vacuum/boost check valve when removing the stock PCV system, and still wanting to run vacuum to the crankcase. Rated at over 100 psi, with a cracking psi of .25psi. -
VTT Billet CNC oil caps add a nice touch of quality to an otherwise plastic-filled BMW engine bay. We offer these in red, black, blue Purple, gold, and clear anodizing. Made from 6061-T6 aircraft aluminum with stainless steel locking tabs. Fits ALL BMWs with a two-prong locking tab design, including but not limited to. N54, N55, S55, S54, N20, S63, S63TU, M54, B58, N63, S65, S85, M57 DieselTHIS CAP DOES NOT FIT, B58TU, S58, A90/91 SUPRA, THIS ONLY FITS 2 PRONG CAP STYLE
-
VTT Ignition Coil Kits
$159.99 – $209.99VTT is proud to offer ignition coil replacements for the N5X platforms, as well as B5X, and many VAG platforms. We started our quest for coils by contacting multiple coil manufacturing companies, paying for individual coils to be made then putting them through rigorous testing in the USA to ensure they matched or exceeded factory output. Once we were satisfied with the testing, we had the best performing coils made to our colors and specs. We offer these coils as complete sets for the N54, B58/S58, and the VAG platforms in either 4, or 5 cylinders. We also offer upgraded plugs which are highly recommended to change when doing coil replacements These coils come in 3 colors, Red, Black, and Blue, and are not simply an aesthetic upgrade but match or exceed the factory secondary spark energy. The VAG coil, is extremely potent, and the tester was so impressed with it compared to the factory coil, he called it a "BEAST" of a coilNote: To extract maximum performance from VTT coils minor tune changes are required to optimize dwell periods. See recommended Dwell times below
-
A well-known issue with the N54 and early N55 with Hydraulic power steering is the plastic pulley either hitting the subframe or simply breaking on its own. This can cause the belt to be ejected from the pulley, and leave you stranded with no serpentine belt. To top it off, if you continue to run the vehicle with the belt off, you also have a good chance of sucking the belt into the engine through the front seal. Put an end to the dreaded plastic PS pulley issues with our 100% Billet Aluminum PS pulley. We make these from 6061-T6 aluminum and anodize them in one of 4 colors (Black, Red, Blue, and Clear) for a great look, and long-lasting finish. These weigh 11Oz, very close to the weight of a stock pulley, and are lighter than the cast aluminum versions on the market.
-
Sale!
VTT Cold Side Charge Pipe
$89.99 – $119.99Whenever upgrading your N54 we suggest going to a true BOV like a Turbosmart Raceport. This cold side charge pipe allows you to do that while getting rid of the prone to cracking plastic charge pipe, and plastic DV's. If you do want to keep the DV set up, we also offer a DV charge pipe. Also available for N55 with no bungs at all, as the DV is on the turbo. Looking for the Charge Pipe & BOV Combo? Click Here -
NGK 94201 Spark plug set for all S58/B58/48 applications, and ALSO for N54/55 running the new B58 coil upgrade. We recommend these for running 100% e85, and high boost on many BMW applications including N54, N55, S55, if you upgrade to the B58 coils. These are also great maintenance replacements for your S58/B58/48 powered vehicle at a much better price than most. Plugs can be bought as a set of 6. You can add pre-gapping for an additional $25
-
Sale!
VTT VAG/BMW/TOYOTA Billet Wheel Spacers
$19.99 – $34.99VTT is proud to offer billet wheel spacers for most VAG, BMW, and the A90/91 Toyota Supra platforms. These spacers are CNC machined from 6061-T6 aluminum and hard anodized black for long corrosion-free life.THESE ARE SOLD INDIVIDUALLY, FOR ONE AXLE ORDER TWO FOR A COMPLETE SET ORDER FOUR.
ANYTHING OVER 5MM WILL REQUIRE LONGER BOLTS OR STUDS, YOU CAN CHOOSE TO ADD A VTT WHEEL STUD KIT FROM THE OPTIONS.
PLEASE DOUBLE CHECK YOUR BOLT PATTERN, AND HUB BORE BEFORE YOU ORDER. INSTALLED SPACERS CANNOT BE RETURNED!
-
NGK 97506 Pre-Gapped Spark Plug Set
$104.99 – $139.99NGK 95706 Spark plug set required for running 100% e85, and high boost on many BMW application including N54, N55, S55, etc. Plugs can be bought as a set of 6. You can add pre-gapping for an additional $25 -
VTT is proud to offer our billet replacement for the factory plastic Oil filter housing cap. This cap does away with the weak plastic cap, and the need for a special tool for removal, while adding some pop, and color to your engine bay. These oil filter housing caps retain ALL of the factory provisions for the filter basket, including the lower pins which are important for the proper function of pressure bypass, etc. They also have cooling fins to help with oil temps. We also designed these caps to complement our Billet Oil caps, and upcoming Billet Power Steering caps, so all 3 will have the same design. Order all 3 - Oil Cap, Oil Filter housing Cap, and Power steering cap for $175 - 10% savings We offer these caps in 4 colors - Red, Black, Blue, and Clear anodize. The cap has a 19mm hex for easy installation, and removal, and includes a new sealing O-ring, and a small O-ring for the oil filter cage.
-
Replacement Gasket for VTT Valve Covers
$29.99 – $64.99Need to replace the gasket on your VTT Aluminum VC? Simply choose your model from the dropdowns to ensure you get the correct version. -
VTT is proud to offer our billet replacement for the factory plastic Coolant Reservoir cap. This cap does away with the weak plastic cap while adding some pop, and color to your engine bay. These Coolant caps retain ALL of the factory provisions by simply allowing you to snap the factory pressure-relief into the new Billet Cap We also designed these caps to complement our N5X Billet Oil caps, N5XBillet Oil filter housing caps, and Billet Power Steering cap and so all 4 will have the same design. We offer these caps in 4 colors - Red, Black, Blue, and Clear anodize, as well as a choice of custom anodize at a cost of $100 extra.
-
VTT is proud to offer our billet replacement for the factory plastic Power steering cap. This cap does away with the weak plastic cap, while adding some pop, and color to your engine bay. These Power Steering caps retain ALL of the factory provisions including dipstick, and vent hole We also designed these caps to complement our N5X Billet Oil caps, and N5XBillet Oil filter Caps caps, so all 3 will have the same design. Order all 3 - Oil Cap, Oil Filter housing Cap, and Power steering cap for $175 We offer these caps in 4 colors - Red, Black, Blue, and Clear anodize
-
One Ethanol Racing Fuel
$69.99 – $559.99Please note: Due to heavy increases in freight costs we have had to raise prices by $50 on 54-gallon drums, and $15 on pails.
VTT is proud to be the West Coast dealer for One Ethanol racing fuel.
We have two blends available in 5-gallon pails and 54-gallon drums. See below for descriptions of both fuels
Fuel is available for local pick up only unless you email, and make arrangements for freight shipping. Be aware fuel is considered hazmat and the freight charges are equal to or more than the fuel in all instances. Fuel CANNOT be shipped normal shipping methods such as UPS, FED EX, etc
-
N55 Stage 1 JB Upgrade Kit (NEW)
From:$1,199.00$1,109.99WHP Level supported (with proper fuel, upgrades, and tuning) Stock – 425WHP -
VTT N54, N55, S55, N20, B58 Billet Motor Mount Inserts
$169.99 – $449.99 -
Looking for a little extra clearance on your coolant tank fitting due to relocation for single turbo, forward-facing intake manifold, etc. This 90-degree fitting will allow you to run the hose straight down instead of straight out, and increase your clearance, and routing choices. Made of 6061-T6 and anodized black for a long-lasting finish. Comes with fitting, and 1 clamp.
-
VTT Billet Crankcase Breather replacement filter
$19.99 – $24.99Need a replacement filter for your VTT Billet Crankcase breather? You can order on here. We offer them in 3 heights, low 48mm, medium58mm, and tall 68mm. This is measured from base to top. The filter will include a new clamp. For reference: N54/55 mostly use the low A90 Supra use Medium Most Audi applications can fit a tall, but measure your filter before ordering. -
VTT Billet N54/N55 Vacuum/Boost Adapter
$49.99 – $64.99We are happy to release our BMW B54/N55 (Limited N55 Fitment) vacuum/boost adapter. These go inline with the Throttle Body fitting and provide a full boost/vacuum signal from the manifold. This fitting adds two 1/8NPT bungs to accept any fitting that has 1/8" NPT threads. You can choose options, 1/4" barb, as well as 1/8NPT plugs if you only want one barb, etc. These are perfect for running your PI off manifold pressure which is much more accurate than charge pipe, and they are also great for BOV running the proper size line without having to drill a hole in your manifold. These do space out any sensors etc giving inaccurate readings like some of the other brands do. They are made from 6061-T6 anodized black, with steel plugs, and Blue Anodized barbed fittings. You can choose to order in a few ways. You can choose straight or 90-degree barbs. Adapter alone - $40 Basic kit - 1 Adapter, 1 barb, and one plug, one vacuum cap, and one zip tie $45.00 Dual Barb kit - 1 Adapter, 2 barbs, one vacuum cap, and one zip tie $55.00 -
The stock outlet adapter on the N54/55 is NOTORIOUS for cracking when removing. This Billet replacement ensures no leaks, and no more cracked adapters. Available in 6 colors! Black, Red, Clear, Blue, Purple, Gold
-
VTT is proud to offer a Titanium hardware upgrade for all our Billet and Cast VC's. This will come with M6x30 Ti bolts N54 /N55/S55/B58 Gen 1/ B58 TU it will be an Umbrella head with a 16.3mm head. These bolts weigh half as much as comparable steel hardware and look amazing. Colors to choose from will be Burnt, Black, and Natural (silver)
-
VTT M14/M12 Titanium Wheel Stud kits
$159.99 – $319.99VTT is proud to offer Titanium wheel stud kits for the owner looking for the lowest possible unsprung weight while maintaining high strength, and good looks as all come with an amazing burnt finish. This kit is 60% lighter than factory steel studs and nuts with a total kit of 20 nuts, and studs being 3.1LBS. Sets of 10 are 1.55 lbs -
VTT Reinforced Universal Silicone Hoses
$9.99 – $14.99VTT offers silicone hoses in various Push-lock sizes, we use these for our catch can kits, but they are also suitable for coolant, vacuum, boost, etc. Do not use with fuel. We offer: -10 Push Lock 24", and 18" -8 Push Lock 24", and 19.5" -6 Push Lock 24" -
VTA Breather
$39.99Not available for single can external PCV Valve. -
VTT is proud to offer our "OBD-LOCK" OBD port locking tool. This tool is made from billet 6061-T6 aluminum and is designed to completely lock out your OBD port from being accessed. This is useful for people who do not want dealers, techs, etc from accessing their OBD port, and possibly changing a tune, etc. This is also perfect for anti-theft prevention as it will not allow a would-be thief to hook up to the car's OBD port, duplicate a key, etc. The OBD-LOCK cannot be removed without physically destroying the OBD port if you do not have the proper tools. VTT uses 5 types of screw head designs for every 200 OBD-LOCKS made. This means that worldwide only 40 OBD-LOCKS are using the same head design. For each batch of 200, we redesign the screw heads meaning every batch of 200 OBD-LOCKS will use different screw heads and tools. Each OBD-LOCK sent has its head design chosen at random. After Extensive testing, we have found that our OBD lock fits EVERY SINGLE OBD port we have tried, this means it will fit every single OBD port currently on the market from a high-end BMW to a Ford F150 diesel. If you order one, and find it does not fit, PLEASE let us know.
FITMENT: We have TWO versions one for ALL GM vehicles and one for ALL NON-GM Vehicles. Please order the one you
-
Sale!
VTT-FAB M7 Copper Locking Exhaust Nuts
$3.00$1.49Are you building a single kit for the N54, N55, or S55 platform? M7 Locking exhaust nuts is not easy. So we made our own to combat the issue. These are the perfect solution to the problem of hard-to-find M7 lock nuts. Sold individually so order the number you need.Note: This is nuts ONLY Stud not included, by our extended M7 studs here - https://vargasturbo.com/product/vtt-fab-extended-m7-n54-n55-s55-b58-2-port-head-studs/
-
VTT-FAB Billet Oil/Coolant Fittings, and block offs
$20.00 – $40.00Looking to fab your own turbo kit for BMW platforms, and need an easy solution to block off water lines, or create feed and drain fittings. Look no further, we offer a wide range of oil/coolant fitting options for most late-model BMW platforms. See the Full description below for a full part number breakdown -
Do you work on a lot of BMW engines from various platforms? Tired of having to adjust universal engine stand plates to fit your engine? Hate not having access to the flywheel end with the engine on the stand? We answered yes to all of those things, we made a tool for anyone that works on BMWs often, and wanted a strong bolt-on engine stand plate that keeps the flywheel end of the engine open! These engine stand plates are machined from a solid billet of 6061-T6 aluminum and anodized in 5 colors for long-lasting corrosion resistance. The engine stand plates currently fit the following engines, N54, N55, S55, B58, S58 with more to come! These are lightweight, and rated for over 1200 lbs! Key Features:
- Lightweight and strong billet 6061-T6, anodized for a long-lasting finish
- Direct bolt on to the intake side motor mount location
- Clears all accessories when installed for easy engine assembly when on stand INCLUDING flywheel or flex plate
- Provisions for location pin, and bar to spin the engine on the stand
-
N55 VR9 TurboSmart KOMPACT EM DV
$239.99 – $269.99VTT Is proud to offer the Turbosmart Kompact EM DV for the N55 The award-winning Kompact EM series Diverter Valves, are the world’s first truly plug and play Diverter Valves. Simply unplug and unbolt your OEM Diverter Valve, and install ours in its place. No adapters, hoses, or extra assembly required. All this while retaining complete OE control of the DV’s operation.
