-
Looking to remove your BOV either for leak testing, or dont want to run one, and your charge pipe or housing has a flange on it. You can use this billet plate to block off the BOV flange. Uses the O-ring from the BOV to seal, and removes the BOV. Fitment: Tial BOV Turbosmart BOV with female flange like Tial
-
VTT “DCS” EWG System for TurboSmart Straight Gates
$799.99 – $1,499.99VTT is proud to offer our EWG "Direct Control System" or DCS! This is a completely new innovation for people looking to control the highest-flowing wastegate on the market using an existing BMW electronic actuator. This system will allow BMW owners who have a vehicle with Electronic Wastegates from the factory to utilize this system to control an externally wastegated turbo system, AND it will ALSO allow ANY vehicle to use this setup to control your own custom turbo system. This is done by utilizing our custom 7075 Billet aluminum bracket coupled with a Turbosmart Straight gate, and if needed an EWG controller made for us by DCCD Pro. This allows direct external wastegate control over any turbocharger system with or without EWG for the factory. Features:- Utilizes the most current wastegate technology the Turbosmart Straight Gate. This gate allows maximum flow with minimal restriction, low drive pressure, and much more. Full details can be found here - https://www.turbosmart.com/product/electronic-straightgate-esg50-external-wastegate/
- Can be configured in multiple ways, and angles based on how you mount the adapter
- The adapter is 7075 Aluminum which has the strength of steel and weight of aluminum
- All connection fittings, are made from Nitronic 60 which has extremely high temperature and wear properties
- Zero Drive Pressure, no springs, no poppet valves, direct control over the gate using factory ECU logic
- Adaptable to ANY turbo system on any car to provide the ultimate in boost control!
-
Looking to protect your single turbo investment, dont have a ton of room, and need a low profile filter that can flow what you need? VTT Has you covered with our Low Profile Single turbo Air Filters. These filters are custom-made for VTT. They are made with a heat-resistant silicone base, and a high-flowing cotton weave element with a pre-oiled design to catch contaminates but allow free flow. We currently offer them in Black, and 3 flange sizes. 3", 4" and 5" flange. With two filter heights. Tested at over 1200WHP with no loss of power observed. Filter Options - Offered in White, and Black with the following dimensions Short - 3.75" Tall, 7.5" OD Large end, 5" Small end 3", 4", or 5" Flange Tall - 4.5" Tall, 7.5" OD Large end, 5" Small end 3", 4", or 5" Flange
-
VTT is proud to offer our "OBD-LOCK" OBD port locking tool. This tool is made from billet 6061-T6 aluminum and is designed to completely lock out your OBD port from being accessed. This is useful for people who do not want dealers, techs, etc from accessing their OBD port, and possibly changing a tune, etc. This is also perfect for anti-theft prevention as it will not allow a would-be thief to hook up to the car's OBD port, duplicate a key, etc. The OBD-LOCK cannot be removed without physically destroying the OBD port if you do not have the proper tools. VTT uses 5 types of screw head designs for every 200 OBD-LOCKS made. This means that worldwide only 40 OBD-LOCKS are using the same head design. For each batch of 200, we redesign the screw heads meaning every batch of 200 OBD-LOCKS will use different screw heads and tools. Each OBD-LOCK sent has its head design chosen at random. After Extensive testing, we have found that our OBD lock fits EVERY SINGLE OBD port we have tried, this means it will fit every single OBD port currently on the market from a high-end BMW to a Ford F150 diesel. If you order one, and find it does not fit, PLEASE let us know.
FITMENT: We have TWO versions one for ALL GM vehicles and one for ALL NON-GM Vehicles. Please order the one you
-
Sale!
BMW Factory OEM EWG Actuator Replacement – 11 65 8 691 853
$499.00$349.00Looking to replace your damaged factory BMW Actuator part number - 11658691853 VTT has located and ordered in bulk these actuators, and offer them at a discounted price. These are 100% FACTORY BMW OEM actuators, not aftermarket. Fitment is for the following, but they work to replace basically any BMW Actuator. -
VTT-FAB Billet Velocity Stack
$39.99 – $49.99Running an open turbo, and want to straight out the airflow to the compressor for extra efficiency. Our billet velocity stack is what you need. Backed by physics a Bellmouth or velocity stack will help smooth the air coming into the turbocharger or on NA cars. These are made from 6061-T6, and anodized in a variety of colors and sizes. Currently, we offer 3", 4", and 5" These are suitable to fit any intake tubing or turbocharger inlet with that size. These are available with or without a silicone connector and clamps. Our V-Stacks are also made to extend down on the outside so you can attach a Vibrant S&B or other compatible 7" Filter on the 3"/4" version. Features:- Smooth air before it enters the turbocharger or Intake
- Very low profile, only sticking 2.5" above the turbocharger inlet. Even if you have no room for a filter these will fit
- Fits all turbochargers with a 3", 4" or 5" inlet including PTE Sportsman Cover!
- 3" and 4" version works with Vibrant #10961 7" filter or S&B 1032 Filter if you have room
- 100% billet construction for high-strength
- Anodized for long life, and durability
-
VTT BMW TITANIUM 5×112 to 5×114 Bolt Pattern Conversion Kits
$189.99 – $369.99Looking to convert your 5x112 M14x1.25 BMW vehicle to 5x114 to open up your wheel options? Want to drop 60% of the weight off steel options? We got covered with our VTT TITANIUM wheel stud conversion kits. These kits are Grade 5 Titanium studs, rated at more than 135,000PSI Tensile Strength, with Grade 5 Titanium nuts with a 60-degree cone seat to fit most all aftermarket wheel applications and convert your vehicle to M12x1.5 wheel studs which allow you to fit 5x114 wheels with no other changes.PLEASE NOTE – THESE STUDS WILL ONLY WORK IF YOUR WHEELS ARE DRILLED M14 THESE WILL NOT WORK FOR WHEELS DRILLED M12!
DO NOT USE ANY HUB-CENTERING SLEEVES WITH THESE CONVERSION STUDS, THE LUGS WILL CENTER THE WHEELS. THE USE OF A CENTERING SLEEVE MAY LEAD TO STUDS BREAKING. FOR INSTALLATION YOU MUST SNUG EACH LUB UP SLOWLY, AND IN A STAR PATTERN TO GET THE WHEEL CENTERED ON THE LUGS, FAILURE TO DO SO CAN ALSO LEAD TO FAILURE.
-
Sale!
VTT BMW Wireless Plug, and Play Line Lock Kit
$649.00$599.00VTT is proud to offer a truly plug-and-play line lock kit for select BMW vehicles that does NOT require running wiring inside the car, mounted switches, holes in the dash, etc. Our newly designed and released line lock kits use a 40amp wireless remote control switch with 4 different modes that allow you to tailor your line lock setup exactly as you prefer. You simply install the solenoids, install the harness with the switch which has all the wiring terminated, bleed the brakes, and you are ready for effortless burnouts which will not be interfered with by the DME because you are holding the brakes, nor wear your rear brake pads. You can store the remote anywhere in your vehicle, center console, cup holder, door cup holder, etc., and when you need to do a burnout to heat your race tires it's in arm's reach without running any wiring into the vehicle. Fitment is confirmed for G8X M3/4, A9X Supra - The kit itself including lines, solenoids, etc will fit most all late model BMW Chassis including F8X, F3X, G2X, etc. The main concern will be mounting the wireless switch in the passenger cowl area. The kit includes:- Line lock solenoids with weather pack connectors
- Two Parker 90-degree -3 an fittings
- Two Stainless Steel adapter fittings
- Two DOT Approved Stainless Steel brake lines
- One complete wiring harness
- One Remote control switch with TWO remotes
-
VTT BMW/Toyota Conversion Wheel Spacers
$54.99 – $69.99Looking to convert your 5×120 or 5x112 vehicle to 5x114.3 wheels, or 5x120 wheels, and open up your wheel options DRAMATICALLY? We got covered with our VTT wheel spacer conversion kits. These kits are machined from billet 6061-T6 aluminum and anodized for a long-lasting finish. We then press in 10.9 class studs, with corrosion-resistant zinc coating for years of use. The spacer then accepts either a 5x114 wheel or a 5x120 wheel. The 5x114 use M14 studs, and the 5x120 use M12 studs. All the spacers have either a 66.6mm or 72.6mm Hub bore size to fit 99% of BMW applications. We offer Hub-Centric adapter rings to fit other wheel bore sizes No wobble bolts or redrilling here. We offer these in 4 thicknesses 15mm, 17.5mm, 20mm, and 25mm. The studs coming out of the spacer are 40″ total length and come with Black Lugnuts. Spacers that convert to 5x120 have M12 studs, ALL others have M14x1.5 -
Need a Tee fitting for plumbing Vacuum, or Boost lines, Don't want to use cheap plastic ones that can get soft when hard, and brittle after they heat cycle? We didn't either, which is why we machined these high-quality billet tees to solve this issue. Machine from 6061-T6 aluminum, and anodized in black for a long-lasting corrosion-free finish, these tees look great, and will you never have to worry about one failing. We offer them in two sizes, each size has 12mm legs and 3 barbs:
- 7.60mm / -4 Push Lock for people looking to use -4 push lock hose or -4 AN hose. This is a perfect fit for those.
- 1/4" For people looking to use 1/4" vacuum tube
-
VTT-FAB Billet Mac Solenoid brackets
$45.99 – $49.99Building a kit using Mac solenoids to control boost? Need an easy way to mount it? VTT-FAB has you covered with our billet Mac Solenoid brackets. Machined from 6061 billet and anodized in 3 colors, these are the perfect way to mount your Mac valve and look good while doing it. Each kit includes:- One Mac Solenoid bracket (3-Port or 4-Port)
- 2 Allen screws to hold the valve to the bracket
- M6 Mounting Bolt
-
VTT is Proud to offer our Billet Aluminum DCT Transmission pan. This pan does away with the factory plastic pan and upgrades it to 6061-T6 aluminum anodized in a variety of colors. This pan increases fluid capacity by 80% or almost DOUBLE the stock pan, has a US-made reusable Viton Gasket, a rare earth magnet built in to pull metal from the fluid, machined external fins to help aid in cooling, and a -6 ORB drain plug. Product Features:
- Billet construction using 6061-T6 aluminum for long life, and added strength
- 80% or Almost DOUBLE the factory fluid capacity at 2000ML compared to 1150ML
- Machined fins for improved cooling
- Rare Erath magnet built in to pull metal from the fluid
- US-Made Viton Gasket
- -6 ORB drain plug for easy service
-
Sale!
VTT BMW Carbon Fiber Driveshaft
$1,899.00 – $1,999.99Why overpay for a custom BMW CF Driveshaft? VTT Is proud to offer our Carbon Fiber Driveshaft for many BMW Models made exclusively for us in the USA by PST one of the leading names n CF driveshaft technology! This driveshaft is made from 3.25" CF tubing Spicer 1350 Yolks, and U-Joints. All pieces are then bonded using PST's proprietary process, and balanced to within 1/8 In/Ounce. We couple the driveshaft with VTT Custom 7075 aluminum adapters which completely eliminate any extra guibos etc. These shafts connect directly to the BMW 3 bolt flange, and our 4340 adapter in the rear to get rid of the screw in the shaft. Made in the U.S.A Each Shaft includes the following- 1 VTT/PST CF Driveshaft with attached VTT 7075 adapters
- 1 VTT 4340 Rear End Adapter
- 1 VTT Billet Adapter installation Tool
- 1 BMW Nut Repair kit
- 6 M8 Rear CV joint bolts (E9X, E46 M3 only)
- 3 M10 Rear flange bolts
- 3 M10 front flange bolts
- 1 Small tube of Loc-tite medium thread locker
CARBON DRIVESHAFTS ARE CONSIDERED CUSTOM PER ORDER AND CANNOT BE CANCELLED ONCE MADE.
PLEASE ORDER CAREFULLY!
-
VTT Carbon Fiber Dragy Holder
$19.99 – $49.00Tired of your Dragy flying all over the car as you try to do runs? Tired of low sats or no sats warning due to improper location of the Dragy in the vehicle? Well say goodbye to those issues with our new Carbon Fiber and Plastic Dragy holders. These are made from either 100% Pre-Preg Carbon Fiber, or molded plastic for a perfect fit. The carbon fiber gives it just the right look to add to your performance vehicle! Each holder has dual Suction cups and will stick to any smooth surface. We suggest mounting them in the upper left or right corner of your windshield with a full view of the sky. Dragy holder features- Stop your Dragy from flying off the dash, and having to search for it
- Position your Dragy in the optimal position for the best satellite coverage
- VTT Dragy holder exposes the entire top of the Dragy so nothing is blocking the receiver from the Satellite
- The charging port is not blocked and can be accessed with the cover on
- Choose from REAL Carbon Fiber or Molded Plastic
-
PTE – Precision Turbochargers
$2,234.49 – $4,428.99VTT is proud to offer PTE Turbocharger products! -
Looking to adapt your wheel bore size to a smaller hub bore? VTT has you covered with our hub-centric adapters. These adapters are made from Billet 6061-T6 aluminum, and anodized in black. We have these sizes currently
- 57.1mm hub to 60.1mm wheel bore
- 57.1mm hub to 64.1mm wheel bore
- 57.1mm hub to 66.1mm wheel bore
- 57.1mm hub to 66.6mm wheel bore
- 57.1mm hub to 67.1mm wheel bore
- 57.1mm hub to 70.3mm wheel bore
- 57.1mm hub to 71.6mm wheel bore
- 57.1mm hub to 72.6mm wheel bore
- 57.1mm hub to 73mm wheel bore
- 57.1mm hub to 74mm wheel bore
- 57.1mm hub to 74.1mm wheel bore
- 64.1mm hub to 72.6mm wheel bore
- 66.6mm hub to 72.6mm wheel bore
They are sold in sets of two, order TWO SETS for a full car, or one set per axle.
