-
Stop the Flex. Launch with Confidence.
Soft bushings are the enemy of hard launches and drivetrain longevity. The factory BMW transfer case bushings—especially on the G8X and F9X platforms—are notoriously soft. That’s the last thing you want when you’re putting serious power down.
Sure, you could replace the entire bushing with a solid one, but that often requires lowering or removing the transfer case—not to mention the added NVH (noise, vibration, and harshness) that comes with it.
Our transfer case bushing inserts offer a smarter solution: reduce bushing flex without sacrificing comfort. You keep smooth, quiet drivability around town and at idle—but when it’s time to launch, the transfer case stays planted.
Fitment Notice – Two Versions Available:
BMW uses two different transfer case bushing types. We now offer Version A and Version B inserts to match.
⚠️ You must physically inspect your vehicle’s bushing to determine which version you need.
We are not responsible for incorrect orders if this step is skipped. -
VTT is proud to offer Titanium wheel stud kits for the owner looking for the lowest possible unsprung weight while maintaining high strength, and good looks as all come with an amazing burnt finish. This kit is 60% lighter than factory steel studs and nuts with a total kit of 20 nuts, and studs being 3.1LBS. Sets of 10 are 1.55 lbs
-
Looking for a way to do burnouts in your ATC13-2 Equipped Xdrive BMW that doesn't have an RWD mode such as G-Series non-M vehicles, and SUVs? We were too! VTT is proud to offer the ONLY easy-to-install, plug, and-play Xdriove controller on the market. This device will allow you to turn off, and turn on again your X-drive capability from the driver seat with a remote. While other options do exist such as X-Delete, or an in-dash gauge, one is a very slow process and is not viable to use as a way to do a burnout at the drag strip, and the other is a very expensive, AND very intrusive device that requires removal of most of the dash, and installing a gauge. Our solution takes 30 seconds to install once you gain access to the underside of the vehicle, and can be removed just as easily. Once installed, you can remotely disable your Xdrive from the driver's seat to perform your burnout, and then quickly enable it again to perform your launch with AWD active. This action does NOT require a key cycle, as soon as you activate it again the car will dismiss any lights and codes generated. This truly is the best of both worlds for ease of use, practicality, and effectiveness, all while coming at a very affordable price. This device uses a BMW plug on one end, and our custom-printed male plug on the other, for a plug, and play OEM fit. NO cutting any wires!
PLEASE NOTE: WHEN ACTIVATED YOUR DASH WILL LIGHT UP WITH CODES BECAUSE YOU ARE IN ESSENCE DISCONNECTING THE TRANSFER CASE. YOU MAY ALSO EXPERIENCE SPORT STEERING DURING THIS TIME WHICH MEANS A HARDER-TO-TURN WHEEL. THIS IS ALL NORMAL. WE ONLY SUGGEST USING THE DEVICE FOR SHORT PERIODS OF TIME, SUCH A BURNOUT AT THE STAGING AREA OF A DRAG RACE. IN SOME INSTANCES, THE CAR WILL NOT ALLOW A BURNOUT IF THE BRAKE, AND THROTTLE ARE APPLIED AT THE SAME TIME DUE TO ECU LOGIC, IN THESE INSTANCES INSTALLING OUR WIRELESS LINE LOCK ELIMINATES THIS ISSUE. MANY TIMES AN AFTERMARKET TUNE WILL ALSO ELIMINATE THIS ISSUE.
THIS DEVICE CAN BE USED FOR THINGS SUCH AS DRIFTING DONUTS ETC., BUT WE DO NOT CONDONE ANY DRIVING OUTSIDE OF LEGAL GUIDELINES. PLEASE USE THIS PRODUCT RESPONSIBLY. SEE ABOVE FOR WHAT IS GOING TO HAPPEN WHEN YOU ENGAGE THIS DEVICE
THIS DOES NOT FIT F-SERIES VEHICLES
Install/User Guide is here - Install Guide
Features:- Works on any vehicle outlined below from stock to tuned
- 30-second install
- 30-second removal
- NON-intrusive ZERO cutting of wires, or taking anything apart on the vehicle TRULY plug and play
- OEM fit and finish on the plugs
-
VTT Carbon Fiber Driveshaft for BMW Applications
Why overpay for a carbon fiber BMW driveshaft?
VTT is proud to offer a premium carbon fiber driveshaft manufactured exclusively for VTT in the USA by GCDS (Gulf Coast Driveshaft) — one of the premier driveshaft manufacturers in the country with extensive experience in high-performance and drag racing applications.
Each driveshaft is constructed using 3.31" carbon fiber tubing, paired with NEAPCO Performance 1350 series U-joints, then bonded using a proprietary high-strength process and precision balanced to within 1/8 in-oz as a complete assembly.
Every shaft is torque tested in-house prior to shipping to ensure proper bonding and structural integrity. GCDS and VTT are among the few manufacturers that perform full torque testing on each shaft before it leaves the facility.
To complete the system, the driveshaft is paired with VTT-designed 7075 aluminum adapters, eliminating the factory guibos and unnecessary flex points. The shaft connects directly to the BMW 3-bolt front flange, while a VTT 4340 rear adapter replaces the factory slip-in / screw-retained shaft design for improved strength and reliability.
Proudly Made in the USA.
PLEASE NOTE! YOU MUST SEND US YOUR VIN NUMBER TO PROPERLY PROCESS YOUR ORDER, IF YOU DO NOT SEND YOUR VIN, YOU ORDER IS GOING TO BE HELD
PLEASE NOTE! Driveshafts can have UNUSUALLY LONG LEAD TIMES. We hope to reduce this with GCDS, but if the shaft shows OUT OF STOCK, expect a lead time of 4–8 weeks, unless we specifically state that it can ship sooner.
Due to the nature of these shafts being manufactured by a 3rd party, ANY ORDERS PLACED FOR VTT CF DRIVESHAFTS ARE 100% FINAL.
NO REFUNDS. NO CANCELLATIONS. FOR ANY REASON.
THIS INCLUDES LONG LEAD TIMES.
PLEASE ORDER CAREFULLY. ONCE THE ORDER IS PLACED, IT IS FINAL.
-
VTT noticed a hole in the VTT A9X Supra/BMW Z4 / G2X / G42 Billet Diff Lock Down Kit market for a high-quality, lightweight, NVH-friendly, and easy-to-install Diff Lock Down kit to improve diff stability under launching, and hard cornering. So we did something about it and went to work on a very innovative design that 100% positively locks the diff down from movement, while shielding it from adding a ton of NVH, and can be used with the stock diff, and subframe bushings. This design uses existing mounting points on the vehicle, you do NOT have to remove the subframe or the Diff to install. Simply remove 4 diff bolts, drill two holes in the subframe slightly bigger, install two M10 riv-nuts, and install the lockdown, you do not even have to move the exhaust. A typical install can be 15-30 minutes for someone who is experienced working on vehicles, an hour if you like taking it slow. You WILL need a Riv-nut tool to install the Riv-nuts, we provide a link below for what we recommend on Amazon. Features:
- Lightweight 1.5 lbs for the entire lockdown plate
- Uses FOUR connection points on the Diff, and two on the subframe for the ultimate in positive diff location, this will stop all diff movement on launch, saving your guibos, etc
- 100% Billet construction from 6061-T6 aluminum
- Anodized in 4 colors for corrosion resistance, a long-lasting finish, and good looks
- The subframe does NOT have to be removed for installation
- Uses all 12.9 grade hardware
- Does not add excessive NVH
- Positively locks down the diff to eliminate all unwanted movement under launches, acceleration, cornering, etc.
All products that are designed to stiffen or reduce drivetrain movement inherently have the tendency to increase NVH or Noise, Harness, or vibration. While these bushings inserts have been found to add little NVH in most instances. Your results and sensitivity to NVH may vary. This product is designed to reduce drivetrain movement, and that was the goal when designing and manufacturing this product. Returns for NVH are not accepted once products are installed.
-
Want to tighten up the diff on your 2021+ G8X M3/M4, A9X Supra, G42 2 Series, or G2X BMW and help eliminate any extra diff movement on hard launches? We got you covered with our Rear Billet diff insert kit. This is pressed into the factory bushing and fills the voids in the bushing. This keeps the stock bushing ride compliance but removes any unwanted movement. These are sold as a kit. To install remove the rear diff bushing, use the stock bolt in press the bushing in, and then replace it with the new bolt washer, and lock nut! Kit includes:
- One Billet Bushing insert
- Two 46mm Hardened Steel Washers
- One 12.9 M14 Bolt
- One M14 Lock nut
THIS KIT MAY REQUIRE LOWERING OF THE SUBFRAME TO GET THE STOCK BOLT OUT, AND THE NEW ONE IN
All products that are designed to stiffen or reduce drivetrain movement inherently have the tendency to increase NVH or Noise, Harness, or vibration. While these bushings inserts have been found to add little NVH in most instances. Your results and sensitivity to NVH may vary. This product is designed to reduce drivetrain movement, and that was the goal when designing and manufacturing this product. Returns for NVH are not accepted once products are installed.DOES NOT INCLUDE DIFF BUSHING IN PHOTO!
-
Want to tighten up the diff on your A9X Supra, G42 2 series, or G2X BMW and help eliminate any extra diff movement on hard launches or cornering? We got you covered with our Billet diff inserts. They are machined from 6061-T6, and anodized black for a long-lasting finish. They install easily by removing the diff bolts one at a time, lowering the diff slightly, inserting the bushing, and installing new washers, and bolts. Kit includes:
- 2 Front inserts
- 2 Rear inserts
- 2 Hardened 46mm washers
- 2 110mm M12x1.5 Bolts
All products that are designed to stiffen or reduce drivetrain movement inherently have the tendency to increase NVH or Noise, Harness, or vibration. While these bushings inserts have been found to add little NVH in most instances. Your results and sensitivity to NVH may vary. This product is designed to reduce drivetrain movement, and that was the goal when designing and manufacturing this product. Returns for NVH are not accepted once products are installed.
-
Looking to fix the diff bolt issue on your G0X X3/X4, G3X 5 Series, and G1X 7 Series chassis? VTT is proud to offer our Rear diff bushing insert kit. This is pressed into the factory bushing and fills the voids in the bushing. This keeps the stock bushing ride compliance but removes any unwanted movement. These are sold as a kit and are available in the rear side only. Kit includes:
- One Billet Bushing insert
- Two 46mm Hardened Steel Washers
- One 12.9 M14 Bolt
- One M14 Lock nut
All products that are designed to stiffen or reduce drivetrain movement inherently have the tendency to increase NVH or Noise, Harness, or vibration. While these bushings inserts have been found to add little NVH in most instances. Your results and sensitivity to NVH may vary. This product is designed to reduce drivetrain movement, and that was the goal when designing and manufacturing this product. Returns for NVH are not accepted once products are installed.
-
VTT Billet & Forged Carbon Strut Bar – BMW G2X Platform (2019+)
We took our popular VTT Billet G8X Strut Bars and redesigned them specifically for the BMW G2X platform. This is not a metal bar wrapped in carbon overlay — it’s a true forged carbon fiber strut bar engineered for both performance and appearance.
Each unit features CNC-machined billet ends crafted from 6061-T6 aluminum or Grade 2 Titanium, providing exceptional strength and precision. Every bar is anodized or polished to perfection and available in Black, Red, Blue, or genuine T2 Titanium rainbow finish.
This upgrade dramatically enhances underhood aesthetics while maintaining proper chassis rigidity and fitment across all 2019+ G2X vehicles.
Key Features
-
Real Forged Carbon Fiber Center – 100% forged carbon, not a metal core with a carbon wrap.
-
Billet Aluminum or Titanium Ends – CNC-machined from 6061-T6 aluminum or T2 Titanium for unmatched durability and strength.
-
Premium Finishes – Choose from Black, Red, Blue anodized, or genuine T2 Titanium rainbow finish.
-
Direct Bolt-On Fitment – Designed to install directly using OEM mounting points. No modification required.
-
-
Looking to maximize your F or G Series BMW for drag racing? Want to be able to dial in the perfect amount of compression or rebound on your launch? The VTT Double adjust drag shock kit is just want the doctor ordered!
-
Sale!Get the COMPLETE lockdown kit for your A9X / G2X / G42 at one low price. Order all 4 pieces together, and save 5%! Transfer Case Bushing are optional
-
Looking to convert your 5x112 M14x1.25 BMW vehicle to 5x114 to open up your wheel options? Want to drop 60% of the weight off steel options? We got covered with our VTT TITANIUM wheel stud conversion kits. These kits are Grade 5 Titanium studs, rated at more than 135,000PSI Tensile Strength, with Grade 5 Titanium nuts with a 60-degree cone seat to fit most all aftermarket wheel applications and convert your vehicle to M12x1.5 wheel studs which allow you to fit 5x114 wheels with no other changes.
PLEASE NOTE – THESE STUDS WILL ONLY WORK IF YOUR WHEELS ARE DRILLED M14 THESE WILL NOT WORK FOR WHEELS DRILLED M12!
DO NOT USE ANY HUB-CENTERING SLEEVES WITH THESE CONVERSION STUDS, THE LUGS WILL CENTER THE WHEELS. THE USE OF A CENTERING SLEEVE MAY LEAD TO STUDS BREAKING. FOR INSTALLATION YOU MUST SNUG EACH LUB UP SLOWLY, AND IN A STAR PATTERN TO GET THE WHEEL CENTERED ON THE LUGS, FAILURE TO DO SO CAN ALSO LEAD TO FAILURE.
-
Product Release: VTT Billet Installation Dowels
Ever tried wrestling a BMW transfer case into a car on your own? Or struggled to line up a transmission or subframe as you're sliding it into place? If you have, you know just how tedious—and downright frustrating—it can be.
After doing these installs hundreds of times, we used to rely on cut-off factory bolts to help guide components into place. But cutting bolts for different applications turned out to be a hassle—time-consuming, inconsistent, and often not long enough to provide the guidance needed.
So we created a better solution: VTT Billet Aluminum Installation Dowels—designed specifically to make these installations easier, faster, and more accurate.
Key Features:
-
One universal length: 6 inches
- Bull nose for easy slip into the part being installed
-
Two thread sizes
-
Three thread pitches
-
Built-in 5mm hex in the end for easy install and removal
Available Thread Options:
-
M10 Standard Pitch – Ideal for BMW transfer case installs and more
-
M12 x 1.5 Fine Thread – Perfect for most BMW front and rear subframe installations
-
M12 Standard Pitch – Designed for BMW transmission installs
-
-
VTT is proud to be an authorized reseller of Race Tech Seats. These are the premiere seats for your drag build or road race car. See Specs/Features below
-
VTT is proud to be an authorized reseller of Race Tech Seats. These are the premiere seats for your drag build or road race car. See Specs/Features below
-
VTT is proud to be an authorized reseller of Race Tech Seats. These are the premiere seats for your drag build or road race car. See Specs/Features below
