1.510.246.9977|Sales@Vargasturbo.com
  • View Cart
    Select options / Details

    VTT-FAB Billet Mac Solenoid brackets

    $45.99 – $49.99
    Building a kit using Mac solenoids to control boost? Need an easy way to mount it? VTT-FAB has you covered with our billet Mac Solenoid brackets. Machined from 6061 billet and anodized in 3 colors, these are the perfect way to mount your Mac valve and look good while doing it. Each kit includes:
    • One Mac Solenoid bracket (3-Port or 4-Port)
    • 2 Allen screws to hold the valve to the bracket
    • M6 Mounting Bolt

  • View Cart
    Select options / Details

    VTT-FAB Billet Oil/Coolant Fittings, and block offs

    $20.00 – $40.00
    Looking to fab your own turbo kit for BMW platforms, and need an easy solution to block off water lines, or create feed and drain fittings. Look no further, we offer a wide range of oil/coolant fitting options for most late-model BMW platforms. See the Full description below for a full part number breakdown

  • View Cart
    Select options / Details

    VTT-FAB Carbon Fiber Turbo Blanket

    $64.99 – $99.00
    Looking to keep the underhood heat down on your single turbo car, or build? We got you covered with our VTT-FAB Carbon Fiber Turbo Blankets. The outer shell is made of Carbon Fiber, and the inner shell is Silica Fiber. For 2500F intermittent / 1800 direct heat rating. We have them in 2 sizes T3, and T4. See fitment below Kit included:
    • 1 Carbon Blanket of choice
    • 2 install springs
    Fitment: T3 blankets are CONFIRMED to fit most T3 housings including PTE V-band, AND they fit PTE T4 V-band In/Out V-band, and PTE divided T4 1.0, 1.15AR, Garret G30/G35 with V-band housing or divided T4 T4 blankets are for larger frame T4 housings and large T4 AR Ratios

  • Sale!
    View Cart
    Add to cart / Details

    VTT-FAB Extended M7 N54/N55/S55/B58 2 Port Head studs

    $2.99
    Are you building a single kit for the N54, N55, or S55 platform? The stock studs are usually a little bit short for most single-head flanges, and finding M7 studs is not easy. So we made our own longer studs to combat the issue. Made from 10.9 grade steel, and coated in black oxide, these are the perfect solution to the short stud problem. Sold individually so order the number you need. Stud details are as follows
    • Overall length 47mm (stock 39mm)
    • 3mm shoulder
    • 6mm head which is 5mm hex
    • 14mm short end
    • 24mm long end (stock 15mm)

    Dont forget our M7 copper lock nuts as well to complete the job - https://vargasturbo.com/product/vtt-fab-m7-copper-locking-exhaust-nuts/

  • View Cart
    Select options / Details

    VTT-FAB Extension Harnesses

    $45.99 – $99.00
    Need to move your coolant expansion tank to the other side of the vehicle for a single turbo kit you are building, extend Map sensor plugs, or IAT, how about Throttle Body? Don't cut your factory wires. Just get a VTT-FAB extension harness, and plug and play! These come in various lengths and are covered in expanded sheathing with heat shrink on both ends for a long-lasting, good-looking finish. Available:
    • Coolant Extension for late model BMW 2015+ 5 ft
    • Pre-Throttle Map sensor extension harness 2 ft
    • Pre-Throttle IAT Sensor extension harness 2 ft
    • B58/S58/B48 etc Throttle body extension harness 2 ft
    • B58 to S55 Throttle conversion/extension harness 2 ft
    • EWG Actuator Extension harness, Various Lengths
    • N54 stock MAP to 3.4 N20 Map sensor extension
     

  • Sale!
    View Cart
    Add to cart / Details

    VTT-FAB M7 Copper Locking Exhaust Nuts

    $1.49
    Are you building a single kit for the N54, N55, or S55 platform?  M7 Locking exhaust nuts is not easy. So we made our own to combat the issue. These are the perfect solution to the problem of hard-to-find M7 lock nuts. Sold individually so order the number you need.

    Note:  This is nuts ONLY Stud not included, by our extended M7 studs here - https://vargasturbo.com/product/vtt-fab-extended-m7-n54-n55-s55-b58-2-port-head-studs/

Title

Go to Top