VTT F9X X3/4M COMPLETE lock down bundle

VTT noticed a hole in the F9X X3/4M market for a high-quality, lightweight, NVH-friendly, and easy-to-install Diff Lock Down kit to improve diff stability under launching, and hard cornering. So we did something about it and went to work on a very innovative design that 100% positively locks the diff down from movement, while shielding it from adding a ton of NVH, and can be used with the stock diff, and subframe bushings. This design uses existing mounting points on the vehicle, you do NOT have to remove the subframe or the Diff to install. Simply remove 4 diff bolts, drill two holes in the subframe slightly bigger, install two M8 riv-nuts, and install the lockdown, you do not even have to move the exhaust. A typical install can be 30-45 minutes for someone who is experienced working on vehicles, an hour or two if you like taking it slow. You WILL need a Riv-nut tool to install the Riv-nuts, we provide a link below for what we recommend on Amazon.

Features:

• Lightweight 1.5 lbs for the entire lockdown plate
• Uses FOUR connection points on the Diff, and three on the subframe for the ultimate in positive diff location, this will stop all diff movement on launch, saving your guibos, etc
• 100% Billet construction from 6061-T6 aluminum
• Anodized in 3 colors for corrosion resistance, a long-lasting finish, and good looks
• The subframe does NOT have to be removed for installation
• Uses all 10.9 and 12.9 grade hardware
• Does not add excessive NVH
• Positively locks down the diff to eliminate all unwanted movement under launches, acceleration, cornering, etc.

Installation Guide - https://vargasturbo.com/wp-content/uploads/2024/02/VTT-F9X-X3-4M-Diff-Lock-Down-Install-Guide.pdf

All products that are designed to stiffen or reduce drivetrain movement inherently have the tendency to increase NVH or Noise, Harness, or vibration. While these bushings inserts have been found to add little NVH in most instances. Your results and sensitivity to NVH may vary. This product is designed to reduce drivetrain movement, and that was the goal when designing and manufacturing this product. Returns for NVH are not accepted once products are installed.

Looking to fix the diff bolt issue on your F9X X3/4M? VTT has taken a 3 pronged approach by offering a triple solution, one part of the solution is the Rear diff bushing insert kit. This is pressed into the factory bushing and fills the voids in the bushing. This keeps the stock bushing ride compliance but removes any unwanted movement. These are sold as a kit and are available in rear side only, and front and rear sides both. Adding in the front side increases installation time, and difficulty as the diff will need to be dropped, and a tool will need to be used to press in the front side bushing

Kit includes:

• One Billet Bushing insert
• Two 46mm Hardened Steel Washers
• One 12.9 M14 Bolt
• One M14 Lock nut
• Optional front side bushing which will fully lock down the bushing. (requires the diff to be lowered, and the bushing pressed into the front)

All products that are designed to stiffen or reduce drivetrain movement inherently have the tendency to increase NVH or Noise, Harness, or vibration. While these bushings inserts have been found to add little NVH in most instances. Your results and sensitivity to NVH may vary. This product is designed to reduce drivetrain movement, and that was the goal when designing and manufacturing this product. Returns for NVH are not accepted once products are installed.

Looking to fix the diff bolt issue on your F9X X3/4M? VTT has taken a 3 pronged approach by offering a triple solution, one part of the solution is the front diff bushing inserts. These are pressed into the factory bushing, and fill the voids in the bushing. This keeps the stock bushing ride compliance but removes any unwanted movement. These are sold as a set

Kit includes:

• Two Billet Bushing inserts
• Two 46mm Hardened Steel Washers

Installation Guide - https://vargasturbo.com/wp-content/uploads/2024/01/VTT-F9X-X3-4M-Front-Bushing-insert-Install-Guide.pdf

All products that are designed to stiffen or reduce drivetrain movement inherently have the tendency to increase NVH or Noise, Harness, or vibration. While these bushings inserts have been found to add little NVH in most instances. Your results and sensitivity to NVH may vary. This product is designed to reduce drivetrain movement, and that was the goal when designing and manufacturing this product. Returns for NVH are not accepted once products are installed.