• Sale!
    The VTT S55 crank bolt capture. slips over the head of the crank bolt fully encapsulating it, and locks it to the crank hub, meaning it cannot back out no matter what.

  • Sale!
    VTT BMW Billet One Way Crankcase Breather VTT is happy to introduce the first and only available plug and play crankcase breather kits for ALL BMW applications that use the two-prong oil tab style oil fill caps. With this breather simply remove your oil cap, install the breather, and instantly free up horsepower, improve turbo draining, and remove crankcase pressure, all while adding a cool look to your engine bay. Can be used by itself with the stock PCV system to eliminate crankcase pressure, or with any number of PCV setups for the ultimate in crankcase pressure relieve Made from 6061-T6 Aircraft aluminum anodized black for a long-lasting finish, 4 stainless steel baffles for complete oil control, a PTFE one-way check ball, a high-quality filter, and clamp all work together to keep crankcase pressure where it belongs, out of your crankcase.

    This breather will fit MOST NOT ALL BMWs with the two-prong style oil fill cap including but not limited to N54, N55, S55, S54, S85, S63, S63TU, N63. There are factors that may stop it from fitting your platform such as valve cover style etc.

  • VTT BILLET BMW N54/55 Crank Seal Guard.

    It is a well-known issue on the BMW N54/N55/S55 platforms that your serpentine belt can fail for various reasons, when this happens you have a high chance of the belt getting sucked behind the front damper, and then being pushed past the crank seal into your oil pan. From there it can get sucked into the oil pick up causing total engine failure, even if you do not lose the engine it is a COSTLY repair to remove the sub-frame and drop the oil pan to remove the belt. The best way to combat this is to watch for oil leaks and keep up on your maintenance. BUT Even with those preventative measures, pre-mature belt failure can occur. This crank seal guard installs over your front crank seal and will keep the belt from being sucked in if a belt failure does occur. This is a cheap way to ensure you do not end up having to replace your motor from oil starvation due to an ingested belt.

  • VTT is proud to announce our N54 Billet/Silicone coolant hose upgrade kit! The factory plastic coolant connectors are prone to breaking over time, and the hoses are just your standard run of the mill coolant hose. We wanted to provide an upgrade to both areas. What we came up with is Billet 6061-T6 connectors anodized black for corrosion resistance, and 6 ply silicone molded silicone hoses in the factory shapes.

  • N54 Aluminum Turbo Outlet

    $229.99$319.99
    Looking to get the most efficient turbocharger operation out of your N54-powered BMW? The best way to do this is to remove all restrictions from the inlet and charge the tract. The factory charge pipe has a very small 1" opening and a poorly designed Y section that couples the two banks into one before entering the intercooler. This VTT N54 Aluminum outlet gets rid of those restrictions and provides a full 1.5" from the turbochargers to a smooth Y transition into a 2.5" outlet to fit most aftermarket intercoolers. Do not be fooled by companies trying to sell you oversized 2" charge pipes, these are not going to pick up any power, and will kill velocity. The smallest diameter you can run while still providing adequate flow is always best for flow velocity and reducing time to TQ.

  • Sale!

    VTT Billet Check Valves

    $24.99$29.99
    VTT CNC Billet check valve that can be used for a variety of uses including a vacuum/boost check valve when removing the stock PCV system, and still wanting to run vacuum to the crankcase. Rated at over 100 psi, with a cracking psi of .25psi.

  • Sale!
    VTT CNC Oil Block off the plate. Use these when you want to delete the stock coolers lines, and run two -10 fittings for your aftermarket oil cooler set up. These provide full flow and get rid of any restrictions. We offer these in THREE colors to match out other N54 billet engine parts such as Oil Cap, PS cap, and Oil Filter housing cap. Available as plate only, with -10 fittings, or -8 fittings

    We suggest running an aftermarket thermostat with a block-off plate to help warm the car up quickly.

  • Sale!
    Price is for Single Bung only.

  • VTT Billet CNC oil caps add a nice touch of quality to an otherwise plastic-filled BMW engine bay. We offer these in red, black, blue Purple, gold, and clear anodizing. Made from 6061-T6 aircraft aluminum with stainless steel locking tabs. Fits ALL BMWs with a two-prong locking tab design, including but not limited to. N54, N55, S55, S54, N20, S63, S63TU, M54, B58, N63, S65, S85, M57 Diesel

    THIS CAP DOES NOT FIT, B58TU, S58, A90/91 SUPRA, THIS ONLY FITS 2 PRONG CAP STYLE

  • Sale!
    VTT is proud to announce a ground-up system designed to give the end-user complete control over their valve cover/ PCV set up. Tired of being told you will run two -10 lines from your VC to your Catch Can? So were we. Now you can run them any way you want, including complete VTA, oil cap one-way breather, etc. Nothing on the market comes close to the versatility of this setup, and it truly is the ULTIMATE Valve cover, PCV combo, or Valve cover, or PCV set up. You choose how many or how few you want to run. Check out this video highlighting some of the features then rea.

  • WHP Level supported (with proper fuel, upgrades, and tuning) Stock - 500WHP

  • Sale!
    This kit comes with 1 set (both turbos) of Stainless Steel wear matched bushing, and flapper assembly, Wastegate arm, rod end, and Stainless steel 8mm C clip.

  • VTT Ignition Coil Kits

    $159.99$209.99
    VTT is proud to offer ignition coil replacements for the N5X platforms, as well as B5X, and many VAG platforms. We started our quest for coils by contacting multiple coil manufacturing companies, paying for individual coils to be made then putting them through rigorous testing in the USA to ensure they matched or exceeded factory output. Once we were satisfied with the testing, we had the best performing coils made to our colors and specs. We offer these coils as complete sets for the N54, B58/S58, and the VAG platforms in either 4, or 5 cylinders. We also offer upgraded plugs which are highly recommended to change when doing coil replacements These coils come in 3 colors, Red, Black, and Blue, and are not simply an aesthetic upgrade but match or exceed the factory secondary spark energy. The VAG coil, is extremely potent, and the tester was so impressed with it compared to the factory coil, he called it a "BEAST" of a coil

    Note:  To extract maximum performance from VTT coils minor tune changes are required to optimize dwell periods. See recommended Dwell times below

  • Buy all 5 Fittings and Save $6. This product includes all of the fittings listed below.
  • VTT B58 Gen-1/TU Billet One Way Crankcase Breather

    VTT is happy to introduce the first and only available plug and play ONE-WAY crankcase breather kit for BMW B58 applications (Supra is different please go to our Supra section if looking for a supra breather) With this breather simply remove your oil cap, install the breather, and instantly free up horsepower, improve turbo draining, remove crankcase pressure, all while adding a cool look to your engine bay. FITS with the engine cover on. Engine cover can be removed, and installed without removing the breather.

  • A well-known issue with the N54 and early N55 with Hydraulic power steering is the plastic pulley either hitting the subframe or simply breaking on its own. This can cause the belt to be ejected from the pulley, and leave you stranded with no serpentine belt. To top it off, if you continue to run the vehicle with the belt off, you also have a good chance of sucking the belt into the engine through the front seal. Put an end to the dreaded plastic PS pulley issues with our 100% Billet Aluminum PS pulley. We make these from 6061-T6 aluminum and anodize them in one of 4 colors (Black, Red, Blue, and Clear) for a great look, and long-lasting finish. These weigh 11Oz, very close to the weight of a stock pulley, and are lighter than the cast aluminum versions on the market.

  • This is a cast version of our incredibly popular Billet CNC valve cover. Instead of starting with a billet piece of aluminum. This cover is cast. then it goes through the same machining process as our billet VC. This keeps the cost down and makes for an awesome valve cover that eliminates the factory plastic cover, and its cyclonic PCV system. This also allows you to run any of our modular PCV fittings, crankcase breather, vacuum relief, billet banjos, catch can kits, etc. This truly is the best bang for your buck Valve Cover upgrade on the N54 market. High quality, low price, great looks, no cracking, and unlimited PCV plumbing options makes this a no brainer upgrade! We offer three color options. Black Wrinkle and Red Wrinkle Powder coat which will hide all casting imperfections, and look the best. There is no charge for powder coating options. We offer custom colors powder coat, at $150. (Please note: Take 2-4 weeks for custom colors)

  • Sale!

    VTT Cold Side Charge Pipe

    $89.99$119.99
    Whenever upgrading your N54 we suggest going to a true BOV like a Turbosmart Raceport. This cold side charge pipe allows you to do that while getting rid of the prone to cracking plastic charge pipe, and plastic DV's. If you do want to keep the DV set up, we also offer a DV charge pipe. Also available for N55 with no bungs at all, as the DV is on the turbo. Looking for the Charge Pipe & BOV Combo? Click Here

  • Sale!
    Made from CNC 6061-T6 Aircraft aluminum anodized black for a long-lasting finish.

  • N54 Silicone Inlets

    $329.99$339.99
    VTT silicone inlets are the premier choice for your N54 inlet needs. Made from high-quality, wire-impregnated silicone, these inlets are a full 6mm thick and can withstand even the harshest underhood conditions.

  • NGK 94201 Spark plug set for all S58/B58/48 applications, and ALSO for N54/55 running the new B58 coil upgrade. We recommend these for running 100% e85, and high boost on many BMW applications including N54, N55, S55, if you upgrade to the B58 coils. These are also great maintenance replacements for your S58/B58/48 powered vehicle at a much better price than most. Plugs can be bought as a set of 6. You can add pre-gapping for an additional $25

  • Sale!
    VTT is proud to offer billet wheel spacers for most VAG, BMW, and the A90/91 Toyota Supra platforms. These spacers are CNC machined from 6061-T6 aluminum and hard anodized black for long corrosion-free life.

    THESE ARE SOLD INDIVIDUALLY, FOR ONE AXLE ORDER TWO FOR A COMPLETE SET ORDER FOUR.

    ANYTHING OVER 5MM WILL REQUIRE LONGER BOLTS OR STUDS, YOU CAN CHOOSE TO ADD A VTT WHEEL STUD KIT FROM THE OPTIONS.

    PLEASE DOUBLE CHECK YOUR BOLT PATTERN, AND HUB BORE BEFORE YOU ORDER. INSTALLED SPACERS CANNOT BE RETURNED!

Title

Go to Top